Agilent Technologies En 45014 user manual

Summary of the content on the page No. 1

Summary of the content on the page No. 2

Summary of the content on the page No. 3

Safety Summary When you notice any of the unusual conditions listed below, immediately terminate operation and disconnect the power cable. Contact your local Agilent Technologies sales representative or authorized service company for repair of the instrument. If you continue to operate without repairing the instrument, there is a potential fire or shock hazard for the operator.
Instrument operates abnormally.
Instrument emits abnormal noise, smell, smoke or a spark-like light during the oper

Summary of the content on the page No. 4

Summary of the content on the page No. 5

Summary of the content on the page No. 6

Summary of the content on the page No. 7

Caution Do not exceed the operating input power, voltage, and current level and signal type appropriate for the instrument being used, refer to your instrument's Operation Manual. Electrostatic discharge(ESD) can damage the highly sensitive microcircuits in your instrument. ESD damage is most likely to occur as the test fixtures are being connected or disconnected. Protect them from ESD damage by wearing a grounding strap that provides a high resistance path to ground. Alternatively, ground yo

Summary of the content on the page No. 8

Summary of the content on the page No. 9

Agilent 4395A N etwork/Spectrum/Impedance Analyzer Operation Manual SERIAL NUMBERS manual applies directly instruments which have the serial number prex JP1KE and MY411. F additional important information about serial numbers , \Serial Number" Appendix D this Manual. Agilent P No . 04395-90030 Printed n i JAP December 2002 Fifth Edition AN art of in read or to This

Summary of the content on the page No. 10

Notice The information contained in this document subject change without notice . This document contains proprietary information that is protected by copyright. rights reserved. No of this document may be photocopied, reproduced, or translated to another language without the prior written consent Agilent T echnologies . Agilent T echnologies Japan, Ltd. Component T PGU-Kobe 1-3-2, Murotani, Nishi-ku, Kobe-shi, Hyogo , 651-2241 Japan c Copyright 997, 1 1998, 2000, 2001, 2002 Agilent T echnologi

Summary of the content on the page No. 11

Manual Printing History The manual printing date and part number indicate its current edition. The printing date changes when a new edition s i printed. (Minor corrections a nd updates t hat are incorporated at reprint do not cause the change .) The manual part number changes when extensive technical changes are incorporated. September 1997 : : :: :: :: :: : : : : : : : : : : : : : : : : : :: :: :: :: : : : First Edition (part number: 04395-90000) September 1998 : : :: :: :: :: : : : : : : : : :

Summary of the content on the page No. 12

Certication Agilent T echnologies certies that this product met its published specications a t the ime t of shipment from the factory . Agilent T echnologies further certies that its alibration c measurements are traceable the United States National Institute of Standards and T echnology , the extent allowed by the Institution’s calibration facility ,or to the calibration facilities of other International Standards Organization members . W arranty This Agilent T echnologies instrument produc

Summary of the content on the page No. 13

Exclusive Remedies The remedies provided herein are buyer’s sole and exclusive r emedies .A gilent T echnologies shall not be liable for any direct, indirect, special, incidental, or consequential damages , whether based on contract, tort, o r any other legal heory t . Assistance Product maintenance agreements and other customer assistance agreements are available for Agilent T echnologies products . F or assistance , contact your nearest gilent A T echnologies Sales and Service Oce . A ddresse

Summary of the content on the page No. 14

Safety Summary The following general safety precautions must be observed during a ll phases of operation, service , and repair of this instrument. F ailure o t w these precautions or with specic W ARNINGS elsewhere in this manual may mpair i the protection provided by the equipment. In addition it violates safety standards of design, manufacture , and ntended i use of the instrument. The A gilent T echnologies a ssumes no liability for the customer’s failure comply with these requirements . 439

Summary of the content on the page No. 15

Dangerous Procedure W arnings W arnings , such as the example below , precede potentially dangerous procedures throughout this manual. Instructions contained in the warnings ust m be followed. Dangerous voltages , capable of causing death, present this W arning instrument. Use extreme caution when handling, testing, and adjusting this instrument. vii in are

Summary of the content on the page No. 16

Safety Symbols General denitions of safety symbols used on equipment manuals are listed below . Instruction manual symbol: product is marked with this symbol when it is necessary for the user refer instruction manual. Alternating current. Direct current. On (Supply). O (Supply). In position of push-button switch. Out position push-button switch. Frame (or chassis) terminal. A connection t o the frame (chassis) f o the equipment which normally include all exposed metal structures . This W arnin

Summary of the content on the page No. 17

Typeface onventions C Bold Boldface type is used when a term dened. F or example: icons symbols . Italics Italic type is used for emphasis and for titles of manuals and other publications . Italic type is also used keyboard entries when a name or a must be typed in place the words italics . F or example: copy lename means to type the word copy ,to type a space , and t hen to type the name a such as file1 . Computer Computer font used on-screen prompts and messages . Labeled keys on the ins

Summary of the content on the page No. 18

Documentation Map The following manuals are available for the analyzer . Operation Manual (Agilent P art Number 04395-900x0) The peration O Manual describes all function accessed from the front panel keys and softkeys . It also provides information on options and accessories available , specications , performance , and some topics about the analyzer’s features . Programming Manual (Agilent P art Number 04395-900x1) Programming Manual shows how write and use B ASIC program control the analyzer a

Summary of the content on the page No. 19

Contents 1. Introduction About the 4395A Network/Spectrum/Impedance Analyzer . . . . . . . . . . . 1-1 About This Guide . . . . . . . . . . . . . . .. .. .. .. . . . . . . . . 1-1 Document Guide . . . . . . . . . . . . . . . .. .. .. .. . . . . . . . . 1-2 2. Installation Guide Incoming Inspection . . . . . . . . . . . . . .. .. .. . . . . . . . . . . 2-2 Replacing Fuse . . . . . . . . . . . . . . . . . . . . . . .. .. . . . 2-4 Fuse Selection . . . .. . . . . . . . . . . . . . . . . . . . . . .

Summary of the content on the page No. 20

Selecting the Input .. . . . . . . . . . . . . . .. .. .. .. .. .. . . 3-6 Setting the Frequency Range . . . . . . . . . . .. .. .. .. .. .. .. 3-7 P erforming the A utomatic Scaling . . . . . . . . .. .. .. .. .. .. .. 3-8 Step 3: Making a Calibration . . . . . . . . . .. .. .. .. .. .. .. . . 3-10 Step 4: Reading a Measurement Result . . . . . . . . .. .. .. .. .. .. 3-12 Reading a M V alue by Using Marker . . . . . . .. .. .. .. .. . Step 5: Printing Out the Measurement Result . . . . . . . .