Summary of the content on the page No. 1
NETWORK CAMERA
Model: IK-WP41A
Quick Start Guide and Important Safeguards
This guide describes the hardware installation.
Refer to the user's manual (PDF file) contained in the CD-ROM for settings, operations
and other information.
The application Adobe Reader is needed to view PDF files. If you do not have this
application, download it from the Adobe Systems Incorporated website.
http://www.adobe.com/
For information on our latest products and peripheral devices, refer to the
Summary of the content on the page No. 2
Introduction FCC (USA)-INFORMATION NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful int
Summary of the content on the page No. 3
Thank you for purchasing the IK-WP41A Network Camera. Before using the camera, read this quick start guide carefully to ensure correct usage. After reading this quick start guide, save it for future reference. The design, specifications, software, and quick start guide contents are subject to change without prior notice. Terms and Trademarks The term "OS" is used in this manual to indicate operating systems compatible with this product. -- Windows XP: Microsoft Windows XP operati
Summary of the content on the page No. 4
Table of Contents Introduction ........................................................................................................................................................ 1 FCC (USA)-INFORMATION ........................................................................................................................ 1 Important Safeguards ....................................................................................................................................... 4 Impo
Summary of the content on the page No. 5
Important Safeguards 1. Read Instructions Read all the safety and operating instructions before operating the product. 2. Retain Instructions Retain the safety instructions and user's manual for future reference. 3. Warnings Comply with all warnings on the product and in the user's manual. 4. Follow Instructions Follow all operating and use instructions. 5. Cleaning Disconnect this camera from the power supply before cleaning. 6. Attachments Do not use attachments not recommended by
Summary of the content on the page No. 6
12. Lightning For additional protection on this camera during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power supply and cable system. This will prevent damage to the camera due to lightning and power-line surges. If lightning occurs, do not touch the unit or any connected cables in order to avoid electric shock. 13. Overloading Do not overload the power supply or extension cords as this can resu
Summary of the content on the page No. 7
Important Safeguards (Cont.) CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamati
Summary of the content on the page No. 8
Notes on Use and Installation Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off. Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen. However, this is not a malfunction. Treat the camera with care Dropping or subjecting the camera to intense vibration may cause it to malfunction. Never touch internal parts Do not touch the internal parts of the camera ot
Summary of the content on the page No. 9
Setting the Network Camera Environment Items needed for network camera monitoring Administrator's personal computer The personal computer that allows setting, operating, monitoring and other functions with the network camera is called the "administrator's personal computer" in this guide. The personal computer for viewing monitored images is called the "user's personal computer" in this guide. The network camera can be viewed by more than one personal computer at the same time.
Summary of the content on the page No. 10
Package Contents IK-WP41A ---- 1 Allen wrench ---- 1 Torx wrench ---- 1 Screw (1/4-20UNC, 12mm) ---- 1 RJ45 Coupler ---- 1 Silica-gel ---- 1 CD-ROM ---- 1 Quick Start guide and Important Safeguards ---- 1 Warranty ---- 1 Physical Description Unit: mm 9
Summary of the content on the page No. 11
Hardware Installation First, use the supplied torx wrench to detach the dome cover from the camera housing. Then, follow the steps below to install the camera. NOTE: Installation should be done only by qualified personnel and conform to all local codes. The supplied torx wrench is exclusively designed to match the dome cover screws. Don’t discard the torx wrench 1. Packing material, Silica-gel and micro SD/SDHC Card 1.1 Packing material Two packing materials on the lens module are
Summary of the content on the page No. 12
Hexagonal screws Housing Lid (2) Attach a silica-gel Get out the supplied silica-gel from the aluminum foil bag, and set it as attached image. NOTE: Treat silica-gel bag with care, Don’t tear the silica-gel package. WARNING: Keep the silica-gel out of the reach of babies, infants, and children. DO NOT EAT, HARMFUL IF SWALLOWED (3) Attach a housing Lid Taking note of the arrowhead, attach a housing lid. Rotate counterclockwise, arrows are united. Both
Summary of the content on the page No. 13
2. Install to the mounting bracket IK-WP41A supports several mounting brackets like pendant mount, wall mount, etc. Select an appropriate bracket according to your location, and purchase separately. Here are major instance of installation. For more information about accessories, visit www.toshibasecurity.com. 2.1 Wall Mount (JK-WM41A) A) Drill 4 holes on the wall matching the mount holes on the plate. Diameter φ3/8” (9.5mm), depth 1/1/2” (39mm). B) Hammer 4 anchor bolts(not supplie
Summary of the content on the page No. 14
13
Summary of the content on the page No. 15
2.2 Wall Mount With Electrical Box (JK-WMB41A) A) Drill 4 holes on the wall matching the mount holes on the plate. Diameter φ3/8” (9.5mm), depth 1/1/2” (39mm) B) Hammer 4 anchor bolts (not supplied) into the holes and secure them. (Figure 1) C) Secure the electrical box to the wall with hex nuts and wrench (not supplied). (Figure 2) D) Loosen the screws of the lid with a supplied torx wrench in the bracket. (Note: Leave in a lower right screw shown in Figure 2.) E) Remove the con
Summary of the content on the page No. 16
Warning: The safety wire must be connected to the camera and wall mount bracket. This will avoid personal hazards if the unit falls from its installation. When installing the camera, secure the safety wire to the screw holes on the bracket. Make sure there are no damaged parts during assembly. A U tube B Hexagon head nuts C Screw for Safety Wire 15
Summary of the content on the page No. 17
16
Summary of the content on the page No. 18
3. Cable connection No. Connector Descriptions For Ethernet connection. Connects this port to the LAN port of Ethernet switch via supplied coupler. 1 RJ-45 Connector Supporting PoE+, this port can connect to the PoE+ switch or PoE+ injector. 24V AC Power Connect the power terminals to a 24V AC power supply and 2 Input(Black/White) and ground the green wire. Ground(Green) Using a pointed object, short both terminals to restart the 3 Reset (Orange/White) camera. Connect
Summary of the content on the page No. 19
Alarm In 5 (Blue) 6 Alarm In 6 (Green) Connect to device that responds to alarm signals. Alarm In GND (White) Alarm In 1 (Red) 7 Connect to device that triggers alarm signals. Alarm in 2 (Brown) Alarm In 3 (Yellow) 8 Connect to device that triggers alarm signals. Alarm in 4 (Orange) Using a pointed object, short both terminals for about 5 9 Default (Pink/Gray) seconds to restart the camera to the factory default. 3.1 Connect the camera to a power source, using one of the followi
Summary of the content on the page No. 20
3.2 Optional connection such as alarm in/out devices to the camera. Network Deployment 1. Connect the Camera to the Network Using an Ethernet cable (not supplied), connect one end to the RJ45 connector of the camera and the other end to the LAN port of the network switch via supplied RJ45 coupler. And connect your client PC to this network switch. 2. Install “IP Camera Finder” on your client PC To make the camera accessible to your network, you must configure appropriate network
