Transition Networks CETTF10XX-200 user manual

Summary of the content on the page No. 1

User’s Guide
CETTF10xx-200
Slide-in-Module Media Converter
• Ethernet
 Copper to Fiber
 10Base-T to 10Base-FL
Transition Networks CETTF10xx-200 series Ethernet
10Base-T to 10Base-FL media converters (designed
to be installed in a PointSystem™ chassis) connect
10Base-T twisted-pair copper cable to multimode or
single mode 10Base-FL fiber-optic cable.
Part Number Port One - Copper Port Two - Fiber-Optic
10Base-T 10Base-FL
CETTF1011-200 RJ-45 ST, 850 nm multimode
100 m (328 m)* 2 km (1.2 miles)*

Summary of the content on the page No. 2

CETTF10xx-200 Installation Installation -- Continued CAUTION: Wear a grounding device and observe electrostatic discharge Install the Slide-in-Module precautions when setting the 4-position switch and the jumper. Failure to CAUTION: Wear a grounding device and observe electrostatic discharge observe this caution could result in damage to, and subsequent failure of, the precautions when installing the CETTF10xx-200 slide-in-module media media converter. converter. Failure to observe this caut

Summary of the content on the page No. 3

CETTF10xx-200 Installation -- Continued Operation Connect the Fiber Cable Status LEDs PWR 1. Locate or build IEEE 803.2™ compliant 10Base-FL fiber cable with male, Use the status LEDs to monitor the media converter two-stranded TX to RX connectors installed at both ends. operation in the network RXF LKF 2. Connect the fiber cables to the CETTF10xx-200 media converter as PWR (Power) On = Connection to external AC power. RXC LKC described: LKF (Link - fiber) On = The fiber link is up.  Connect

Summary of the content on the page No. 4

CETTF10xx-200 Operation -- Continued Cable Specifications The physical characteristics must meet or exceed IEEE 802.3™ specifications. Product Features Fiber Cable AutoCross™ Bit Error Rate: <10-9 The AutoCross feature detects and configures the twisted-pair copper port on the CETTF10xx-200 media converter to the correct straight-through (MDI) or Single mode fiber (recommended): 9 µm Multimode fiber (recommended): 62.5/125 µm crossover (MDI-X) configuration. This feature allows either MDI

Summary of the content on the page No. 5

CETTF10xx-200 Cable Specifications -- Continued Technical Specifications For use with Transition Networks Model CETTF10xx-200 or equivalent. Copper Cable Standards IEEE 802.3™ Category 3: (minimum requirement) Data Rate 10 Mb/s Gauge 24 to 22 AWG Attenuation 11.5 dB/100m @ 5-10 MHz Dimensions 3.4" x 0.86" x 5.0" (86 x 22 x 127 mm) Maximum Cable Distance 100 meters Weight 3 oz (91 g) (approximate) Power Consumption 2.3 watts Category 5: (recommended) Gauge 24 to 22 AWG MTBF 408,231 hours (MIL2

Summary of the content on the page No. 6

CETTF10xx-200 Troubleshooting Contact Us If the media converter fails, isolate and correct the failure by determining the Technical Support answers to the following questions and then taking the indicated action: Technical support is available 24 hours a day. US and Canada: 1-800-260-1312 1. Is the PWR LED illuminated? International: 00-1-952-941-7600 NO  Is the media converter slide-in-module installed properly in the Transition Now chassis? Chat live via the Web with Transition Networks Techn

Summary of the content on the page No. 7

Compliance Information CISPR22/EN55022 Class A & B + EN55204 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A & B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the i