Summary of the content on the page No. 1
HSIM-G01/G09
User’s Guide
HSIM-G
SX LNK
9032398-04
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Only qualified personnel should perform installation procedures. NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDE
Summary of the content on the page No. 4
Notice INDUSTRY CANADA NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
Summary of the content on the page No. 5
Notice CABLETRON SOFTWARE PROGRAM LICENSE 1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions of this License Agreement. You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as authorized in writing by Cabletron. 2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program. 3. APPLICABLE LAW. This
Summary of the content on the page No. 6
Notice SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERS THE HSIM-G01/G09 GIGABIT ETHERNET MODULES USE CLASS 1 LASER TRANSCEIVERS. READ THE FOLLOWING SAFETY INFORMATION BEFORE INSTALLING OR OPERATING THESE ADAPTERS. The Class 1 laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This control loop eliminates the need for maintenance checks or adjustments. The output is factory set, and does not allow any user adjustment. Class 1 laser transceivers c
Summary of the content on the page No. 7
Notice DECLARATION OF CONFORMITY Application of Council Directive(s): 89/336/EEC 73/23/EEC Manufacturer’s Name: Cabletron Systems, Inc. Manufacturer’s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03867 European Representative Name: Mr. J. Solari European Representative Address: Cabletron Systems Limited Nexus House, Newbury Business Park London Road, Newbury Berkshire RG13 2PZ, England Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC EC Dir
Summary of the content on the page No. 8
Notice vi HSIM-G01/G09 User’s Guide
Summary of the content on the page No. 9
CONTENTS CHAPTER 1 INTRODUCTION 1.1 Using This Manual....................................................................... 1-2 1.2 Document Conventions ............................................................... 1-2 1.3 Getting Help................................................................................. 1-3 1.4 Overview...................................................................................... 1-4 1.4.1 Connectivity ...........................................
Summary of the content on the page No. 10
Contents viii HSIM-G01/G09 User’s Guide
Summary of the content on the page No. 11
CHAPTER 1 INTRODUCTION Welcome to the Cabletron Systems HSIM-G01/G09 User’s Guide. This manual describes the HSIM-G01 and HSIM-G09 and provides information concerning features, installation, troubleshooting, the use of Local Management, and specifications. The HSIM-G01 and HSIM-G09 function identically with one NOTE exception: the HSIM-G01 uses a short wavelength laser device that connects to 50 or 62.5 micron multimode fiber optics, and the HSIM-G09 uses a long wavelength laser dev
Summary of the content on the page No. 12
Chapter 1: Introduction 1.1 USING THIS MANUAL Read through this manual completely to familiarize yourself with its content and to gain an understanding of the features and capabilities of the HSIM-G. The following list provides an overview of each section of this manual: Chapter 1, Introduction, outlines the contents of this manual, describes the HSIM-G features and concludes with a list of related manuals. Chapter 2, Installation, describes how to install an HSIM-G i
Summary of the content on the page No. 13
Getting Help 1.3 GETTING HELP For additional support related to this device or document, contact Cabletron Systems using one of the following methods: World Wide Web http://www.cabletron.com/ Phone (603) 332-9400 Internet mail support@cabletron.com FTP ftp://ftp.cabletron.com/ anonymous Login Password your email address To send comments or suggestions concerning this document, contact the Cabletron Systems Technical Writing Department via the following email addre
Summary of the content on the page No. 14
Chapter 1: Introduction 1.4 OVERVIEW The HSIM-G extends the functionality of certain Cabletron Systems interface modules or standalone devices by providing high-speed uplink capability through Gigabit Ethernet technology. Section 1.4.1 and Section 1.4.2 give information on some of the features of the HSIM-G. 1.4.1 Connectivity The HSIM-G01 module supports 1000Base-SX, providing one SC fiber optic connector for 50 or 62.5 micron multimode fiber optics. The HSIM-G09 module supports
Summary of the content on the page No. 15
CHAPTER 2 INSTALLATION Only qualified personnel should install or service this unit. To install the HSIM-G you need the following items: • Antistatic wrist strap • Phillips screwdriver Before attempting to use the HSIM-G you should be familiar NOTE with the IEEE 802.3z specification. The network installation must meet the guidelines contained in the draft specification to ensure satisfactory performance of the equipment. 2.1 UNPACKING THE HSIM-G The HSIM-G and the host mo
Summary of the content on the page No. 16
Chapter 2: Installation 2.2 INSTALLING AN HSIM-G You can install an HSIM-G in any Cabletron Systems device that supports HSIM technology (e.g., 2E42-27, 6E132-25). Refer to the release notes for the version of firmware running NOTE on the host platform to ensure that the HSIM-G is supported. “Host platform” is used to designate the interface module or standalone device into which the HSIM-G is installed. The following sections provide instructions for installing an HSIM-
Summary of the content on the page No. 17
Installing an HSIM-G Standoff Screws HSIM Coverplate Faceplate Mounting Screws Host Platform coverplate Figure 2-1 Removing the HSIM Coverplate 7. Refer to Figure 2-2 and place the HSIM-G behind the module faceplate. 8. Align the HSIM connector of the HSIM-G with the HSIM pins on the module. When installing the HSIM-G, ensure that the HSIM pins on the module or device align with the HSIM-G connector to prevent ! CAUTION bending the pins. This can damage both the HSIM-G and the
Summary of the content on the page No. 18
HSIM-G SX LNK Chapter 2: Installation Ensure that the standoffs on the interface module align with the NOTE standoff screw holes on the HSIM-G. 10. Secure the HSIM-G to the module faceplate using the mounting screws saved in step 5. 11. Secure the HSIM-G to the module standoffs using the standoff screws saved in step 6. 12. Reinstall the interface module in the chassis. 13. Reattach the network cabling to the module. Standoff Screws Connector Connector Cutaway View of Connector HSIM-G HSIM
Summary of the content on the page No. 19
Installing an HSIM-G 2.2.2 Installing an HSIM-G in a Standalone Device To install an HSIM-G into a standalone device (e.g., 2E42-27), perform the following steps: 1. Power down the device and remove the power cord. To install the HSIM-G in a standalone device, the device must first be powered down. Ensure that you remove the power cord and ONLY the screws required to remove the chassis cover. 2. Disconnect any cables connected to the network ports of the device. Note the ports that have cables
Summary of the content on the page No. 20
Chapter 2: Installation 11. Secure the HSIM-G to the module standoffs using the standoff screws saved in step 6. Ensure that the chassis cover is in place before reconnecting the power cord. 12. Reattach the chassis cover to the standalone device, reconnect the power cord, and reconnect the standalone device to the network. 2.3 CONNECTING TO THE NETWORK The HSIM-G has an SC style connector for the network port. Cabletron Systems offers fiber optic cables that use SC style connectors which are
