Summary of the content on the page No. 1
User Manual
MDS932AE-10BT STANDALONE
MDS932AE-FXO STANDALONE
MDS932AE-FXS STANDALONE
MDS933AE-10BT STANDALONE
MDS932C-10BT RACK-CARD
MDS933C-10BT RACK-CARD
G.SHDSL Modem
USER MANUAL
Version 1.2
Revision 26 January 2004
Document name MDS933AE-v1.2.doc
Summary of the content on the page No. 2
Summary of the content on the page No. 3
User Manual VERSION CONTROL..........................................................................................................5 1 GENERAL INFORMATION........................................................................................6 ORDER INFORMATION .....................................................................................................7 2 DESCRIPTION OF THE DEVICE ..............................................................................8 2.1 Exterior des
Summary of the content on the page No. 4
User Manual 8.4 Line1 and Line2 Connector.............................................................................24 9 DESCRIPTION OF INTERFACE CABLES..............................................................25 9.1 Ethernet cable.................................................................................................25 9.2 DSL cable........................................................................................................25 Version: 1.2 Page. 4 of 25
Summary of the content on the page No. 5
User Manual VERSION CONTROL Version Date Major changes to previous version 1.0 31.12.2001 Initial version of the manual corresponding to version 1.2 of the device micro program 1.1 23.10.2003 New function description corresponding to software release V1.6 Corrected Connecter description 9.1 Changed DSL cable to twisted type 10.2 1.2 26.1.2004 Manual corresponding to software version 1.7 Implementation of rack card models Version: 1.2 Page. 5 of 25
Summary of the content on the page No. 6
User Manual 1 GENERAL INFORMATION • High-speed symmetrical data transmission over one physical copper twisted pair with the 135 Ohm impedance according to ETSI TS 101 135. • ITU-T G.991.2 (G.shdsl) line encoding. • Line rate in the range from 72 Kbit/s to 2320 Kbit/s in 2 wire mode Line rate in the range from 144 Kbit/s to 4624 Kbit/s in 4 wire mode • Manual or automatic mode of line-speed adjustment. • Ethernet 10/100Base-T interface, Full/Half duplex. • Transmition of VLAN packet (I
Summary of the content on the page No. 7
User Manual ORDER INFORMATION Modem AccessDSL Discovery, G.shdsl, 10/100Base-T Bridge, MDS932AE-10BT VLAN, Adapter 220 Vac Modem AccessDSL Discovery, G.shdsl, 1 or 2 pairs, up to MDS933AE-10BT 4.6Mbps, 10/100Base-T Bridge, VLAN, Adapter 220 Vac Modem AccessDSL Discovery, G.shdsl, 10/100Base-T Bridge, MDS932AE-FXS VLAN, Adapter 220 Vac, with FXS interfaces Modem AccessDSL Discovery, G.shdsl, 10/100Base-T Bridge, MDS932AE-FXO VLAN, Adapter 220 Vac, with FXO interfaces Version: 1.
Summary of the content on the page No. 8
User Manual 2 DESCRIPTION OF THE DEVICE 2.1 Exterior design Desktop models The front panel of the device has 3 LEDs: LOCAL informs the user about the status of the local device. The following four statuses are possible «blinking red» informs the user about malfunctioning of the modem’s hardware and software. In this case, the modem is out of order and should be submitted to the service center for being repaired. «red» informs the user about an urgent alarm. An abruption of
Summary of the content on the page No. 9
User Manual The back panel of the MDS932AE-10BT and MDS933AE-10BT modem has: • The grounding bolt of the modem (option); • The “AC12V” power connector. The connection of the modem to the 220 V power supply is implemented using an external power supply unit; • the “Monitor” connector to control the modem and store statistics; • “PC” and “HUB” connectors to connect the modem to the LAN using a straight Patch Cord (to the PC or HUB, respectively); • the “DSL” connector to connect the mo
Summary of the content on the page No. 10
Summary of the content on the page No. 11
User Manual Status(L) informs the user about the status of the local device. The following four statuses are possible «blinking red» informs the user about malfunctioning of the modem’s hardware and software. In this case, the modem is out of order and should be submitted to the service center for being repaired. «red» informs the user about an urgent alarm. An abruption of the connection, the correspondence of the signal-to-noise ratio which does not allow to transmit informatio
Summary of the content on the page No. 12
User Manual 3 RULES OF SWITCHING 3.1 The standalone delivery set The delivery set includes: • the subscriber access device (a modem) • the power supply source (an AC adapter) • the cables for the line connections 3.2 The rack-card delivery set The delivery set includes: • the subscriber access device (a modul) • the cables for the line connections 3.3 Connection rules During the connection of the modem stick to the following rules: • connect the modem using the “straight” Patch Co
Summary of the content on the page No. 13
User Manual To update the information on the screen use the “Enter” key. The following menu will appear on the screen. Input Password: Please enter your programmed password. The unit will be delivered with the default password “admin” After entering the password the following menu will appear. Discovery G.SHDSL Ethernet Monitor V1.7 +-----------------------+ + Main Menu + +-----------------------+ 1. Perf
Summary of the content on the page No. 14
User Manual 4 THE COMMAND SYSTEM 4.1 Basic rules After the command is typed, press . The key is used to edit commands. It is necessary to input item number, for choising menu item, You can use “PageUP”, “PageDown” and “Space” keys, for scrolling list of available value of parameters, The “Esc” key is using for channeling of new value of parameters or returning to up menu screen. 4.2 The main menu The main menu is the following: Discovery G.SHDSL
Summary of the content on the page No. 15
User Manual 4.3 Performance management submenu Upon activation of the performance management submenu the following message will be displayed. Performance Management 1.Loop Status... 4.EtherNet Status... Select item number or ESC to Upper level menu>> 4.3.1 Loop Status submenu Upon activation of the performance management submenu the following message will be displayed.
Summary of the content on the page No. 16
User Manual 4.3.2 Ethernet Status submenu Upon activation of the performance management submenu the following message will be displayed. Performance Management->EtherNet Status Link:Link down Link Speed:---- Link Duplex:---- Used Entries:0 Tx Packets:0 Rx Packets:0 Fwd Packets:0 Drop Packets:0 Speed:Auto Duplex:Auto MAC Address:00-00-00-00-00-00
Summary of the content on the page No. 17
User Manual 4.4.1 DSL Setup In this menu you can setup the DSL link. When you have selected that menu, the following will appear: Configuration Management->DSL Setup 1.[Loop 1 Operation Mode]:Slave 2.[Loop 1 Auto/Fixed]:Fixed 5.[Loop 1 Fixed Connection Speed]:2312K(36N) 6.[Loop 1 Annex]:A/B 7.[Loop 1 Tx Level Adjustment]:0 dB 18.[2W/4W]:2W
Summary of the content on the page No. 18
User Manual 4.4.1.4 Fixed Connection Speed (only if Fixed is selected) • In the Fixed Connection Speed menu, you can specify your desired speed in the range of 72 kbps to 2312 kbps for 2wire units and 144 kbps to 4624 kbps for 4wire models 4.4.1.5 Annex • With the Appendix menu you can choose between A, B, A / B. If you don’t know what Annex you have to setup, and then use the A / B configuration. 4.4.1.6 Tx Level Adjustment • In the Tx Level Adjustments menu you can setup you desired
Summary of the content on the page No. 19
User Manual 4.4.2 Ethernet Setup submenu Configuration Management->EtherNet Setup 1.[Speed]:Auto 2.[Duplex Mode]:Auto 3.[Disable Mac Filter]:No 4.IP Address>>192.168.5.105 5.Subnet Mask>>255.255.255.0 6.Gateway Address>>192.168.5.1 Select item number or ESC to Upper level menu>> • In the Speed menu, you can setup the Ethernet speed to t
Summary of the content on the page No. 20
User Manual 5 TECHNICAL SPECIFICATIONS The main technical specifications of modems of the Black Box family are presented below in the table. Line interface. Standard ETSI 101 135 Number of pairs 1 Line rate 2 wire models 72 – 2312 Kbit/s 4 wire models 144 – 4624 Kbit/s Communication range for cables with 0.4 mm: 0.9 mm: the wire diameter of approx: aprox: 144 Kbit/s 8.2 km 31 km 2320 Kbit/s 3.6 km 13.7 km (values are depending on noise environment and line quality) Line
