Summary of the content on the page No. 11
“Installation Wizard” to run Vivotek’s installation program. Upon Installation Wizard’s start up, a searching box will pop up. This program searches for Vivotek’s product on the same LAN: After searching, Vivotek Video Servers or Network Cameras will be located by the Installation Wizard. There may be several entries shown in the window. The Administrator may differentiate the Network Cameras with the serial number. - 7 - www.vivotek.com T: 886-2-824552
Summary of the content on the page No. 12
For the series number in the “Serial Number” field, please check the label on the bottom of the camera. The IP addresses shown in the "Current IP Address" field reflect those on the local network. They may be from the DHCP server. If there is no DHCP server, the camera will try to find a free IP address (this takes from 15 second to 3 minutes, depending on the LAN status). The method of finding IP address is seeking from 192.168.0.99, to 192.168.0
Summary of the content on the page No. 13
For more detailed usage of the Installation Wizard, please refer to the user’s manual of the Installation Wizard. - 9 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532
Summary of the content on the page No. 14
Initial Access to the Network Camera Installing Plug-in For the initial access to the Network Camera in Windows, the web browser may prompt for permission to install a new plug-in for the Network Camera after a period of time of downloading. Permission request depends on the Internet security settings of the user’s PC or notebook. If the highest security level is set, the computer may prohibit any installation and execution attempt. This plug-in has been registered for certifi
Summary of the content on the page No. 15
Check Network Settings The Network Camera can be connected either before or immediately after software installation onto the Local Area Network. The Administrator should complete the network settings on the configuration page, including the correct subnet mask and IP address of gateway and DNS. Ask your network administrator or Internet service provider for the detail information. By default the Network Camera requires the Administrator to run installation every time it rebo
Summary of the content on the page No. 16
Add Password to Prevent Unauthorized Access The default Administrator’s password is blank and the Network Camera initially will not ask for any password. The Administrator should immediately implement a new password as a matter of prudent security practice. Once the Administrator’s password is saved, the Network Camera will ask for the user’s name and password before each access. The Administrator can set up a maximum of twenty (20) user accounts. Each user can access the Ne
Summary of the content on the page No. 17
How to Use Authentication After opening the web browser and typing in the URL of the Network Camera, a dialogue window pops up to request a username and password. The foreground is the login window and the background shows the message if authentication fails. The user may check the option box to save the password for future convenience. - 13 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532
Summary of the content on the page No. 18
Primary User’s Capabilities Main Screen with Camera View The main page layout has three parts: Configuration functions: The camera can be configured using these user interfaces. Camera View: What the camera sees. Pan/Tilt/Zoom control buttons: These buttons provide a command interface to control the aim of the camera. CCD control buttons: These buttons provide a command interface to control the aim of the camera. - 14 - www.vivotek.com T: 886-2-82455282 F: 886-2
Summary of the content on the page No. 19
The Configuration: “Digital Output” Clicking on the “On” or “Off” button turns the digital output to either on or off status. “Snapshot” Clicking on the “Snapshot” can get a JPEG format image of the current camera view in another window. “Client Settings” Clicking on this button links you to the client setting page, please check the following session for more details. “Configuration” Only the Administrator can access camera configurations. The camera view The informa
Summary of the content on the page No. 20
“Pan speed” This selection box sets the moving range of the “Left” and “Right” commands. “Tilt speed” This selection box sets the moving range of the “Up” and “Down” commands. “Zoom speed” This selection box sets the moving range of the “zoom in” and “zoom out” commands. “Focus speed” This selection box sets the moving speed of the “focus near” and “focus far” commands. The focus function is obvious when the optical zoom time is larger than 7. “Auto pan” This button
Summary of the content on the page No. 1
Summary of the content on the page No. 2
Product name: Network Camera (PZ61x2) Release Date: 2005/03/28 Manual Revision: 1.10 Web site: www.vivotek.com Email: technical@vivotek.com sales@vivotek.com Made in Taiwan. ©Copyright 2000-2005. All rights reserved - 1 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532
Summary of the content on the page No. 3
Before You Use This Product The use of surveillance devices may be prohibited in your country by law. The Network Camera is not only a high-performance web-ready camera but also can be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use. It is important to first verify that all contents received are complete according to the list in the "Package Contents
Summary of the content on the page No. 4
Package Contents PZ61x2 Camera stand Power adapter Software CD A/V Cable Quick installation guide Remote Controller Warranty card - 3 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532
Summary of the content on the page No. 5
Table of Contents Table of Contents............................................................................................ 1 Installation..............................................................................................4 Hardware Installation ...........................................................................4 To install in Ethernet.................................................................. 4 Software Installation ................................
Summary of the content on the page No. 6
Product Demo for E-business – Large-scale Service ..................... 23 If the web space has FTP service............................................... 24 If the web space has no FTP service .......................................... 25 Build a Security Application............................................................ 27 Send Snapshots When Motion is Detected .................................. 28 Definitions in Configuration ............................................
Summary of the content on the page No. 7
Appendix ...............................................................................................59 A. Troubleshooting ............................................................................. 59 B. Cleaning the Lens........................................................................... 63 C. Pan/Tilt/Zoom Data ........................................................................ 63 D. URL Commands of the Network Camera .........................................
Summary of the content on the page No. 8
Installation Hardware Installation Please verify that your product package contains all the accessories listed in the foregoing Package Contents. Depending on the user’s application, an Ethernet cable may be needed. The Ethernet cable should meet the specs of UTP Category 5 and not exceed 100 meters in length. Connect the power adapter jack to the Network Camera before plugging in to the power socket. This will reduce the risk of accidental electric shock. Upon power
Summary of the content on the page No. 9
Consult with the dealer of the peripherals for correct installation. 1 DI+ INPUT (Max. 50mA, 12VDC) 2 DI- INPUT (Initial state of DI is low) 3 SW_COMMON OUTPUT (open from SW_OPEN at initial state) (close with SW_OPEN when set DO to ON) 4 SW_NOPEN OUTPUT (Max. 1A, 24VDC or 0.5A, 125VAC) - 5 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532
Summary of the content on the page No. 10
Software Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refers to the person who can configure the Network Camera and grant user access to the camera. At the end of the hardware installation, the Administrator must place the product software CD into the CD-ROM drive of the PC running in MS Windows. An auto-run program will pop up (If the program is not on auto-run, go to the root directory of the software CD and c
