Summary of the content on the page No. 1
XL-12000S
Managed, High-Speed Network Modem
USER GUIDE
TUT SYSTEMS
Summary of the content on the page No. 2
Summary of the content on the page No. 3
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE Warranty Policy Warranty Summary This Tut Systems product is warranted against defects in material and workmanship and will substantially conform to Tut Systems product documentation for a period of one (1) year from the date of shipment. Y2K Compliance The Company’s products, including separately sold software applications, are designed to be used prior to, during, and after the calendar year 2000 and will operate during each such time per
Summary of the content on the page No. 4
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The information contained in this publication is the latest available. However, Tut Systems reserves the right to change specifications of hardware and software without prior notice. Purchasers of Tut Systems’ products should make their own evaluation to determine the suitability of each product fo
Summary of the content on the page No. 5
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE Table of Contents 1.0 XL-12000S Product Overview 1 2.0 Technical Specifications 2 3.0 What’s in the Box 3 4.0 Installation 4 5.0 Panel Indicators and Connectors 7 5.1 Front Panel Indicators 7 5.2 Rear Panel Indicators and Connectors 9 6.0 Power and Boot Up Sequence 10 7.0 Configure the Modem 11 7.1 Quick Start 11 7.2 Detailed Procedures 14 7.2.1 Choosing the Appropriate Bridging/Routing Option 14 7.2.2 User Interface Keyboard Commands 26 7.2
Summary of the content on the page No. 6
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE Figures Figure 4.1 RJ-45 10Base-T Straight-through Cable 4 Figure 4.2 RJ-11 DSL Line Cable 5 Figure 4.3 XL-12000S Installation with a Hub or Node 6 Figure 5.1 XL-12000S Front Panel 8 Figure 5.2 XL-12000S Rear Panel 9 Figure 7.1 Serial Session/Version ID Screen 13 Figure 7.2 Bridging Example One (Basic Bridging) 15 Figure 7.3 Bridging Example Two (Advanced Bridging) 17 Figure 7.4 Routing Example One 20 (Using a Router and Bridge Com
Summary of the content on the page No. 7
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE Tables Table 7.1 Keyboard Commands 27 Table 7.2 Specific Field Information for the Modem 34 Management Screen Table 7.3 Specific Field Information for the Modem Configuration Screen 37 Table 7.4 Specific Field Information for the Password Change Screen 40 Table 8.1 Specific Field Information for the SNMP Management Screen 42 Table 8.2 Specific Field Information for the DHCP Relay Agent Screen 44 Table 8.3 Specific Field Information for the U
Summary of the content on the page No. 8
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE vi TUT SYSTEMS
Summary of the content on the page No. 9
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE 1.0 XL-12000S Product Overview The XL-12000S modem is a high-speed, SDSL (Symmetrical Digital Subscriber Line) point-to-point managed modem created to extend Local Area Networks (LANs) up to 12,000 feet using ordinary tele- phone wires. The modem uses Digital Subscriber Line (DSL) trans- mission technology to deliver data at 2 Mbps. The XL-12000S is designed for easy installation. Front panel LEDs provide status and operational information.
Summary of the content on the page No. 10
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE 2.0 Technical Specifications Data Rate: 2.048 Mbps Line Length: Up to 12,000 ft. on 24 AWG wire Up to 9,000 ft. on 26 AWG wire Ethernet Interface: Compliant with IEEE 802.3 10Base-T Console Interface: RS-232 Operating Voltage: 120/240 VAC 50/60 Hz wall transformer Power Consumption: 5 Watts Operating Temperature: -5˚ to 55˚ C Storage Temperature: -40˚ to +70˚ C Relative Humidity: 5% to 90% (non-condensing) Compliance: UL, CSA, CE, FCC Part
Summary of the content on the page No. 11
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE 3.0 What’s in the Box Confirm that there is one each of the following items: Description • XL-12000S Modem • XL-12000S User Manual • RJ-45 10Base-T Straight-through Cable • RJ-11 DSL Line Cable • Wall Transformer w/Lightning Protection • XL-12000S Enterprise SNMP MIB Diskette You will also need a PC with a serial port and a serial cable to connect to the modem’s point of connection, which is an RS-232 Console port (DB-9 female). 3.0 WHAT’S
Summary of the content on the page No. 12
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE 4.0 Installation 1. Remove the modem and wall transformer from the shipping car- ton. Remove the wall transformer from its box. Remove the plastic wrapper from around the modem. a. Remove the cable ties from each of the cables and place them side by side. b. Each of the cables is identified as follows: (1) RJ-45 10Base-T straight-through cable: A cable with RJ-45 connectors is used to connect the modem to a 10Base-T hub or node. If connecti
Summary of the content on the page No. 13
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE Figure 4.2 RJ-11 DSL Line Cable 5 2 3 3 4 4 2 5 2. Select a convenient location near the Ethernet device to which the modem will be connected. The modem should be kept away from excessive heat or cold. Operating temperature range is -5˚C to 55˚C. 3. Connect an RJ-45 straight-through cable from the 10Base-T Ethernet connector of the XL-12000S to an Ethernet device (PC, server, workstation or hub) as shown in Figure 4.3. If connecting to a P
Summary of the content on the page No. 14
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE Figure 4.3 XL-12000S Installation with a Hub or Node. Switch in Normal (Hub) Position 10Base-T Cable Note: The Ethernet connection switch facilitates use with either a hub or node. 6 TUT SYSTEMS 4.0 INSTALLATION 10BASE-T 12VDC CONSOLE ETHERNET DSL - + 10BASE-T ETHERNET LINK CONNECTION CROSSED NORMAL CONNECT CONNECT RJ-11 RS-232 RJ-45 TO HUB TO NODE XL-12000S
Summary of the content on the page No. 15
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE 5.0 Panel Indicators and Connectors This section describes the indicators and connectors on the front and rear of the XL-12000S modem. 5.1 Front Panel Indicators Figure 5.1 shows the LED indicators that provide status and opera- tional information on the XL-12000S Modem. Power LED The blue Power LED remains lit while the unit has power. Activity LEDs The DSL RX and DSL TX LEDs flash green when receiving and transmitting data. Status LED A
Summary of the content on the page No. 16
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE Figure 5.1 XL-12000S Front Panel DSL RX Flashing Green: On when receiving data. POWER DSL TX Blue Flashing Green: On when transmitting data. TUT SYSTEMS XL-12000S HIGH SPEED LAN MODEM STATUS DSL LINK Flashing Red: Steady Green: Normal link. Power up self-test or software download in progress. Flashing Green: Linking (about one minute). Off: Normal condition. Off: No link. Steady Red: Board failure. Contact Tut Systems Customer Support. 8 TU
Summary of the content on the page No. 17
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE 5.2 Rear Panel Indicators and Connectors 10Base-T Link LED A green LED indicates a valid Ethernet link. When flashing, the LED indicates traffic on the link. When the LED is off, there is no valid link. If this occurs, see section 10.0, “Troubleshooting”. Console Port The console port (RS-232) connects to a PC with a VT-100 terminal or PC VT-100 emulator for opening a management session. Figure 5.2 XL-12000S Rear Panel 12VDC 10BASE-T CONS
Summary of the content on the page No. 18
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE 6.0 Power and Boot Up Sequence 1. Verify that the LAN and DSL lines are connected according to the wiring diagram described in the “Installation” section (see Figure 4.1 or Figure 4.2). 2. Plug the 120 VAC/12 VDC wall transformer (220VAC for inter- national use) into a wall outlet. Verify that the Power (blue) LED comes on. 3. Verify that the 10Base-T Link (green) LED on the rear panel is illuminated. If the unit is not connected to an Ether
Summary of the content on the page No. 19
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE 7.0 Configure the Modem This section provides two options for performing modem configura- tion. The “Quick Start” (section 7.1) option provides a basic Spanning Tree Protocol (STP) enabled bridge mode configuration with no remote management or password protection. The “Detailed Procedures” section (section 7.2) provides detailed steps covering all modes of modem operation. Before beginning either option, make sure the power and boot up seque
Summary of the content on the page No. 20
XL-12000S MANAGED, HIGH-SPEED NETWORK MODEM USER GUIDE a. From the Windows 95/Windows 98 screen select “Start.” b. Select “Programs” (or Open file Hypertrm.exe). c. Select “Accessories.” d. Select “HyperTerminal.” When the HyperTerminal icon appears, double-click on it. e. On the Connection Description icon, assign a name (e.g. Modem1) to the icon for future purposes. Press “OK”. (When Phone Number tab appears, press “Cancel”.) f. Select File / Properties: Press the button on the Pro
