Transition Networks SPS-1872-CC user manual

Summary of the content on the page No. 1

SPS-1872-CC (Conversion Center™)
User’s Guide
SPS-1872-DPS (Dual PointSystem™)
SPS-1872-xx
SPS-1872-PS (PointSystem™)
External Power Supply
SPS-1872-SA (Stand-Alone)
18-60 VDC and 24-30 VRMS
SPS-1872-SA
SPS-1872-CC
SPS-1872-DPS
SPS-1872-PS
The Transition Networks SPS-1872-xx external power supply provides a wide range
of input power (18-60 VDC and 24-30 VRMS) to accommodate most industrial,
telecom, and commercial applications. The SPS-1872-xx can deliver 12 watts of
power, enough to power all

Summary of the content on the page No. 2

SPS-1872-xx Installation and Service Installation -- Continued All Installation and service must be performed by qualified service personnel. SPS-1872-SA (Stand Alone) Read and follow all warning notices and instructions marked on the product or NOTE: The SPS-1872-SA external power supply is shipped with four (4) included in the manual. attached feet. 1. Place on any well-ventilated table-top or shelf with access to a power Required Grounding source with a range between 18-60 VDC or 24-30 VRMS.

Summary of the content on the page No. 3

SPS1872-xx Installation -- Continued Installation -- Continued SPS-1872-CC (Conversion Center™) SPS-1872-DPS (Dual PointSystem™) 1. Remove the left-rear and right-rear screws from the Conversion Center™ 1. Remove the left-rear and right-rear screws from the Dual PointSystem™ media converter. media converter. 2. Connect the barrel connector on the SPS-1872-CC to the power port of 2. Connect the barrel connector on the SPS-1872-DPS to the power port of the media converter The flange of the SPS-1

Summary of the content on the page No. 4

SPS-1872-xx Installation -- Continued Maintenance Supplying Power to the SPS-1872-xx Replacing the Fuse CAUTION: The power source MUST BE TURNED OFF when connecting it to CAUTION: The external power source MUST BE POWERED OFF when the SPS-1872-xx external power supply. Failure to observe this caution could replacing the fuse to the SPS-1872-xx external power supply. Failure to observe result in damage to, and subsequent failure of, the SPS-1872-xx and any attached this caution could result

Summary of the content on the page No. 5

SPS1872-xx Technical Specifications Technical Specifications -- Continued For use with Transition Networks Model SPS-1872-xx or equivalent. Input: Product is certified by the manufacturer to comply with DHHS Rule 21/CFR, Input Voltage 18 - 60 VDC, 24 - 30 VRMS Subchapter J applicable at the date of manufacture. Isolation Voltage (Dielectric withstand) Meets IEC 950 for one minute Compliance UL listed EN60950; FCC & CISPR class A; CE Mark 1500 VAC: Output/Input 1500 VAC: Input/Safety GND Dimens

Summary of the content on the page No. 6

SPS-1872-xx Contact Us Compliance Information Technical Support UL Listed Technical support is available 24 hours a day. C-UL Listed (Canada) United States: 1-800-260-1312 CISPR/EN55022 Class A + EN55024 International: 00-1-952-941-7600 FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable Transition Now protection against harmful interference when th

Summary of the content on the page No. 7

Trademark Notice All trademarks and registered trademarks are the property of their respective owners. Copyright Restrictions © 2003, 2005 Transition Networks. All rights reserved. No part of this work may be reproduced or used in any form or by any means – graphic, electronic, or mechanical – without written permission from Transition Networks. Printed in the U.S.A. 33266.E