Summary of the content on the page No. 1
Installation and
Installation and
User’s Manual
User’s Manual
Tandberg LTO2 Autoloader
Tandberg LTO2 Autoloader
Date: August 18, 2003
Document Number: 432778
Revision:01 CAUTION:
Be sure to read this manual before using this product.
Carefully store this manual after reading.
Summary of the content on the page No. 2
Trademarks Linear Tape-Open, LTO and Ultrium are trademarks of Hewlett-Packard, IBM Corporation and Seagate Technology. Microsoft, Windows, Windows NT, and its logo are registered trademarks of Microsoft Corporation in the United States and other countries. Other brands and product names appearing herein may be trademarks or registered trademarks of their respective owners. FCC Class B Notice This device complies with Part 15 of FCC Rules. Operation is subject to the follow
Summary of the content on the page No. 3
Keep this operation manual on hand so that you can refer to it when needed. Be sure to read “Safety Precautions” before using this product. Safety Precautions- Be sure to read this section before using this product. – Safety Descriptions This manual describes dangers that may be caused by ignoring the cautions and the ways to avoid those dangers. Warning labels are attached on the components that may cause danger. “Warning” and “caution” terms are used for warning labels to d
Summary of the content on the page No. 4
Symbols and Their Meanings Used in This Manual and Warning Labels Attention Indicates the risk of an electric Indicates the risk of smoke or shock. fire. Indicates non-specific, general Prohibited action Do not disassemble, repair or Indicates non-specific, general modify. An electric shock or action that is prohibited. fire may result. Indicates non-specific, general action that is prohibited. Mandatory action Unplug the power supply plug Indicates
Summary of the content on the page No. 5
Safety Cautions Read and understand warnings, cautions and instructions described below in order to use this product safely. For descriptions of symbols used below, refer to the aforementioned “Safety Description.” General Cautions WARNING Do not use when smoke, foul smell or abnormal noise are emitted. If smoke, foul smell or abnormal noise is given off, immediately turn off the power switch and pull out the power plug from the outlet. Then, contact the dealer you purc
Summary of the content on the page No. 6
Cautions for power source or power cable WARNING Do not handle the power plug with wet hands. Do not connect/disconnect the plug with wet hands. Otherwise, an electric shock may occur. CAUTION Do not insert the plug into the outlet other than the one specified. Use the wall outlet of specified voltage and power source. Use of power sources other than the one specified may cause a fire or electrical leakage. Do not apply starburst wiring. This device may over
Summary of the content on the page No. 7
Cautions for installing, transporting, storing, and connecting CAUTION Do not lift the device alone. This device weights 18 kg. Lifting it alone may injure your back. Be sure to transport or move the device with two persons. Do not install in location other than the one specified. Do not install this device in the location listed below or other than the location specified in this manual as a fire may occur. Dusty place Humid place such as near a hot water supp
Summary of the content on the page No. 8
Cautions of maintenance WARNING Do not disassemble, repair or modify by yourself. Never disassemble, repair or modify this device. Doing so results in the danger of an electric shock or a fire as well as operation error of the device. Do not clean the device with the plug still inserted in the outlet. Turn the power off and remove the power cable from the outlet before cleaning. Touching parts inside the device while the power cable is connected may lead to an electric sh
Summary of the content on the page No. 9
Cautions during operation CAUTION Caution: Suction. Do not place hands or hair close to the cooling fan on the back panel while operating the device as hands may be pinched or hair may be sucked in. Do not insert hands inside the transporter, as it may cause an electric shock or injury. Do not touch the device when there is lightning. If there is possibility of lightning, pull out the power plug from the outlet. In case lightning strikes before pulling out the power pl
Summary of the content on the page No. 10
WARNING Label WARNING labels are affixed to or around the parts where latent dangers exist so that customers are always aware of the dangers when operating the device (therefore, do not remove or soil the labels). If any of the labels are not affixed, peeling off or stained, contact our dealers. Figure WARNING Label Figure WARNING Label Figure Top view of the Tandberg LTO2 Autoloader WARNIN
Summary of the content on the page No. 11
Revision History This Revision History provides a concise publication record of this manual. It lists the manual revision levels, release dates, and reasons for the revisions. Document No. / Rev Level / Date 432778 / 01 / 2003-08-13 - ix -
Summary of the content on the page No. 12
Contents Safety Precautions- Be sure to read this section before using this product. –............ i Safety Descriptions .................................................................................................................... i Symbols and Their Meanings Used in This Manual and Warning Labels ................................ii Safety Cautions ........................................................................................................................iii General Caut
Summary of the content on the page No. 13
3.6 Setting the SCSI ID........................................................................................................... 26 3.6.1 Checking the SCSI ID................................................................................................ 26 3.6.2 Changing the SCSI ID................................................................................................ 27 3.7 Using the Emergency Release Key .........................................................................
Summary of the content on the page No. 14
Introduction Tandberg LTO2 Autoloader is an external memory device that has been developed for the file systems of servers and other equipment. This large capacity, high-performance streaming cartridge tape device is designed for use in medium intermediate to top-level computer systems. This manual describes the overview, operation, maintenance method, regular maintenance, and troubleshooting of this device so as to avoid maintenance faults. Please keep this manual in a safe p
Summary of the content on the page No. 15
Organization of this manual This section describes the organization of this manual and an overview of each chapter. Use it when you would like to find out something about this device. Chapter 1 Tandberg LTO2 Autoloader This chapter describes the features of the Autoloader as well as the package contents and the names of the parts. It also covers precautions for handling and storage. (See the description at the beginning of the manual concerning precautions for the safe handling
Summary of the content on the page No. 16
Symbols used in this manual Symbols used in this manual The following symbols are used to indicate cautions or tips for operations. (For symbols related to safety precautions, please refer to the descriptions aforementioned.) Important Indicates handling methods of this product, software operational instructions, or special notes. Tip Indicates helpful and useful information. - xiv -
Summary of the content on the page No. 17
Chapter1 Tandberg LTO2 Autoloader Some preliminary information about the Tandberg LTO2 Autoloader is presented here before installation and handling. 1.1 Overview of the Tandberg LTO2 Autoloader This is a high-performance, high-capacity data storage device that is connected to the supported host to provide additional host storage. The Autoloader is designed to run an unattended backup and is furnished with the following functions. The LTO2 Autoloader has one built-in LTO U
Summary of the content on the page No. 18
1.2 Names and Functions of the Parts This section describes the names and functions of the Tandberg LTO2 Autoloader parts. 1.2.1 Front Panel of the Tandberg LTO2 Autoloader Figure 1-1 Front Panel of the LTO2 Autoloader Front door This door prevents the intrusion of foreign objects. While the power is ON, unlock the door lock with the door lock key supplied with the main unit. Key lock The front door
Summary of the content on the page No. 19
Liquid Crystal Display This liquid crystal display (LCD) is organized in 2 lines of 10 characters, and 11 icon characters. It displays the status of the Autoloader, menus, and error information. Alarm LED This LED lights (in red) should some kind of fault arise in the Autoloader. Power LED This LED lights (in green) when the power is supplied and the power switch is ON; it is unlit when the power is OFF. Panel keys (arrow) key : Moves forward thr
Summary of the content on the page No. 20
1.2.2 Rear Panel of the Tandberg LTO2 Autoloader Figure 1-2 Rear Panel of the LTO2 Autoloader AC Power connector This connector supplies power to this device. Plug in the AC power cable supplied with the main unit. SCSI connector These connectors are used to connect a SCSI interface that controls this device. Connect the SCSI cable of the server, workstation, or other equipment. Filter Element The F
