Summary of the content on the page No. 9
Quick Setup Guide 1 Introduction The TANDBERG Management Server is a server that comes with the TANDBERG Management Suite (TMS) pre-installed. This guide will take you through the initial steps of setting up the TANDBERG Management Server before first time use. Please refer to the Getting Started section of the TANDBERG Management Suite Installation Manual – Getting Started as well as the TANDBERG Management Suite Administrator’s Guide for further information on how to configure
Summary of the content on the page No. 10
TANDBERG Management Server Quick Setup Guide 2 Installation Precautions: Never install communication wiring during a lightning storm. Never install jacks for communication cables in wet locations unless the jack is specifically designed for wet locations. Never touch uninstalled communication wires or terminals unless the communication line has been disconnected at the network interface. Use caution when installing or modifying communication lines. Avoid using communicati
Summary of the content on the page No. 11
Quick Setup Guide 2.1 Unpacking To avoid damage to the unit during transportation, the Management Server is delivered in a special shipping box, which should contain the following components: User Manual and other documentation on CD. Rack-ears, screws and screwdriver. Cables: o Power cable o Ethernet cable TANDBERG Management Server Installation site preparations Make sure that the Management Server is accessible and that all cables can be easily connected. For ven
Summary of the content on the page No. 12
TANDBERG Management Server Quick Setup Guide 2.2 Connecting cables LAN cable Connect a LAN cable from the ‘LAN 1’ connector on the Management Server to your network. The LAN 2, 3 and 4’ connectors are not used and should be left open. Power cable Connect the system power cable to an electrical distribution socket. Press the power switch button at the back side to ‘1’ to turn on the Management Server. On the front panel of the system the power indicator LED, marked ‘Pwr’, wi
Summary of the content on the page No. 13
Quick Setup Guide 2.3 IP Address Setting Configuration The Management Server requires the IP Address Settings to be configured before it can be used. IP Address Configuration can be made using the LCD Panel. Front view of the Management Server with the LCD panel: LCD Panel buttons and their functions: Up and Down Used to select items in the menu, move between values in a arrows numerical address and modify numerical values. Enter Used to enter the edit mode and co
Summary of the content on the page No. 14
TANDBERG Management Server Quick Setup Guide 5. Move between characters by using the Up and Down arrows. Edit values by pressing Enter and using the Up or Down arrow to modify. Press Enter again to confirm the value, or press Return to restore the value to its previous state. 6. When finished editing the address, press Return. You will be asked to confirm your address entry on the following screen. At the Save Changes? Prompt, use the Up or Down arrow to select Yes and press Enter to confi
Summary of the content on the page No. 15
Quick Setup Guide 3 Product Registration and Updates You need to register the product if you would like to receive an email from TANDBERG Constant Care Services when Management Server updates to the TANDBERG Management Server become available. You can also check the following ftp site for all available downloads: http://ftp.tandberg.net/pub/software/tms/ 3.1 Security Updates All relevant security updates for the TANDBERG Management Server are available from the following ftp sit
Summary of the content on the page No. 16
TANDBERG Management Server Quick Setup Guide 4 General Use TANDBERG Management Server The Management Server should always be turned on. The unit itself should not be available to users at any time. If the system does not respond: Check the LCD panel to determine if the unit is switched on and ‘live’. Make sure that the Management Server is switched on by using the On/Off switch located at the rear of the unit. Restart the Management Server using the LCD panel. For det
Summary of the content on the page No. 17
Quick Setup Guide 4.1.2 How to shutdown the Management Server 1. Press Enter to display the Main Menu screen. 2. From the Main Menu screen, use the Up or Down arrow to select Commands. 3. Press Enter to confirm your selection. 4. From the Commands menu, use the Up or Down arrow to select Shutdown and press Enter. 5. You will be asked to confirm this action on the following screen. At the Shutdown? prompt, use the Up or Down arrow to select Yes and press Enter to confirm. Please note
Summary of the content on the page No. 18
Summary of the content on the page No. 19
5 Administrator Settings Before the TANDBERG Management Server can be taken into use, some basic settings need to be configured. 5.1 Operating System Settings You can access the Web User Interface for Microsoft Windows Server administration to configure operating system settings. 1. Start a web browser and enter the address https://:8098, where is the IP address of the Management Server. 2. When prompted for login, enter t
Summary of the content on the page No. 20
TANDBERG Management Server Quick Setup Guide To set the password of the local administrator account, click the Set Administrator Password menu item under the Welcome tab. From the Maintenance tab, you can set the date, time and time-zone. 5.2 TANDBERG Management Suite Settings You can access the Web User Interface for the TANDBERG Management Suite (TMS) to configure TMS settings. 1. Start a web browser and enter the address of the Management Server. 2. When prompted for
Summary of the content on the page No. 1
Management Server
Quick Setup Guide
D13939 Rev 04
This document is not to be reproduced in whole or in part without permission in writing from:
Summary of the content on the page No. 2
TANDBERG Management Server Quick Setup Guide Trademarks and Copyright All rights reserved. This document contains information that is proprietary to TANDBERG. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, electronically, mechanically, by photocopying, or otherwise, without the prior written permission of TANDBERG. Nationally and internationally recognized trademarks and trade names are the property of their
Summary of the content on the page No. 3
Quick Setup Guide Environmental Issues Thank you for buying a product, which contributes to a reduction in pollution, and thereby helps save the environment. Our products reduce the need for travel and transport and thereby reduce pollution. Our products have either none or few consumable parts (chemicals, toner, gas, paper) and low energy consuming products. Waste handling There is no need to send any products or material back to TANDBERG as there are no consumables to take ca
Summary of the content on the page No. 4
TANDBERG Management Server Quick Setup Guide Operator Safety Summary For your protection, please read these safety instructions completely before operating the equipment and keep this manual for future reference. The information in this summary is intended for operators. Carefully observe all warnings, precautions and instructions both on the apparatus and in the operating instructions. Equipment Markings The lightning flash symbol within an equilateral triangle is intended t
Summary of the content on the page No. 5
Quick Setup Guide Servicing - Do not attempt to service the apparatus yourself as opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to qualified service personnel. Damaged Equipment - Unplug the apparatus from the outlet and refer servicing to qualified personnel under the following conditions: When the power cord or plug is damaged or frayed If liquid has been spilled or objects have fallen into the app
Summary of the content on the page No. 6
TANDBERG Management Server Quick Setup Guide Contact us If you have any questions, comments or suggestions, please see the Online Support service at www.tandberg.com It is also possible to send a fax or mail to the attention of: Product and Sales Support TANDBERG P.O. Box 92 1325 Lysaker Norway Tel: +47 67 125 125 Fax: +47 67 125 234 vi
Summary of the content on the page No. 7
Quick Setup Guide End-User License Information IMPORTANT: THE USER MANUAL CD FOR THIS PRODUCT CONTAINS IMPORTANT TERMS AND CONDITIONS INCLUDING END USER LICENSE AGREEMENTS. THE LICENSE AGREEMENTS SHOULD BE READ PRIOR TO USE. USE OF THIS PRODUCT CONSTITUTES ACCEPTANCE OF THE TERMS OF THE LICENSES. vii
Summary of the content on the page No. 8
TANDBERG Management Server Quick Setup Guide Table of Contents 1 Introduction......................................................................................................................... 9 2 Installation......................................................................................................................... 10 2.1 Unpacking................................................................................................................... 11 2.2 Connecting cabl
