Summary of the content on the page No. 1
REJ10J0746-0110
R8C/15, R8C/17 StarterKit
Tutorial
RENESAS SINGLE-CHIP MICROCOMPUTER
M16C FAMILY / R8C/Tiny SERIES
Rev.1.10 Renesas Solutions Corp.
Revision date : Mar 01, 2005 www.renesas.com
Summary of the content on the page No. 2
Keep safety first in your circuit designs! 1. Renesas Technology Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii)
Summary of the content on the page No. 3
Table of Contents 1.accessory softwares to install 2.Until a sample program is operated with an emulator software P4 2.1 Flash programmer (Flash development toolkit) Installation P4 2.2 Emulator Software, C Compiler and High-performance Embedded Workshop Installations P10 2.3 USB driver installation P14 2.4 Operate Sample Program P18 3
Summary of the content on the page No. 4
1. accessory softwares to install 1) Note the following points before installing. a) The M3T-NC8C has already been installed. b) The M3T-NC30WA has already been installed. c) The emulator software has already been installed. Install the software attached to this product after uninstalling the above software. 2) The directory and file names including space cannot be used. 3) The sample program uses C compiler, High-performance Embedded Workshop and emulator software to this produ
Summary of the content on the page No. 5
Click “OK”. Click “Next” Select language to be used and click "Next" 5
Summary of the content on the page No. 6
Only when you agree with License Agreement, click "Yes". Click “Next”. Click “Next”. 6
Summary of the content on the page No. 7
Remove a check. Click “Next” Click “Next”. Refer to a new folder name, or select from the existing folder list and Click “Next”. 7
Summary of the content on the page No. 8
Refer to a new folder name, or select from the existing folder list and Click “Next”. Click “Next”. Click “Install”. 8
Summary of the content on the page No. 9
Click “finish”. 9
Summary of the content on the page No. 10
2.2 Emulator Software, C Compiler and High-performance Embedded Workshop Installations 1) Installation Double-click an installer of CD-ROM ¥ dlp_tool ¥. 2) Installation procedures are described below. Select the language to be used and click “Next”. Click “Next” 10
Summary of the content on the page No. 11
Only when you agree with License Agreement, click "Yes". Select all and click “Next” Refer to a new folder name, or select from the existing folder list and click “Next”. 11
Summary of the content on the page No. 12
Refer to a new folder name, or select from the existing folder list and click “Next”. Click “Yes” Check the setting before starting the installation and if the setting is correct, click “Next”. 12
Summary of the content on the page No. 13
Check the setting before starting the installation and if the setting is correct, click “Next”. Then, a copy will be started. Click “Finish”. 13
Summary of the content on the page No. 14
2.3 USB driver installation Connect the E8 emulator using the USB cable to the USB port of host machine. Installation procedures are described below. If the E8 emulator is connected, it is recognized as a new hardware. Click “Next” after selecting “Install the software automatically”. Click “Continue”. Microsoft has advocated authentication of the USB drivers to the USB vendors in the Microsoft® Windows® XP and Windows®-based operating systems released after
Summary of the content on the page No. 15
Renesas USB drivers are not authenticated by Microsoft, but we provide them based on the sufficient examination. Insert CD-ROM and specify ¥dlp_tool¥DRIVERS¥USB¥XP¥. Click “OK”. Click “Finish”. The installation is completed above. 15
Summary of the content on the page No. 16
Installation procedures are described below. If E8 emulator is connected, it is recognized as a new hardware. Click “Next” and start installing a driver. Put a check into “search for the best driver for your device” and click “Next”. Insert CD-ROM and Put a check into “Specify a location”. Specify ¥dlp_tool¥DRIVERS¥USB¥ME¥ (or ¥98¥) and click “Next”. 16
Summary of the content on the page No. 17
Click “Next”. Click “Finish”. The installation is completed above. 17
Summary of the content on the page No. 18
2.4 Operate Sample Program 1) Copy ¥Japanese¥M3A0115_17¥PROGRAM¥ in CD-ROM to the given folder. 2) Change a file attribute Since the copied file attribute is set to “read-only”, change it to the attribute which can be read or written. Select “Property” of the copied folder and set to the attribute which can be read or written. Remove a check of “Read-only” and click “Apply”. (Figure shows for Windows XP) Remove a check Put a check into “Apply changes to this f
Summary of the content on the page No. 19
Click “OK”. The installation is completed above. 19
Summary of the content on the page No. 20
Select all files in the copied folder by a mouse. Select “File” and “Property”. Remove a check of “Read-only” and click “Apply”. 20
