Summary of the content on the page No. 1
MVME712-12, MVME712-13,
MVME712A, MVME712AM,
and MVME712B
Transition Modules
and LCP2 Adapter Board
User’s Manual
(MVME712A/D3)
Summary of the content on the page No. 2
Notice While reasonable efforts have been made to assure the accuracy of this document, Motorola, Inc. assumes no liability resulting from any omissions in this document, or from the use of the information obtained therein. Motorola reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of Motorola to notify any person of such revision or changes. No part of this material may be reproduced or copied in any tangible medi
Summary of the content on the page No. 3
Preface This manual provides general information, hardware preparation, installation instructions and support information for the following transition modules: MVME712-12 MVME712A MVME712B MVME712-13 MVME712AM The manual also provides information about the LCP2 Adapter Board. The transition modules are used as the interface between Motorola Single Board Computer VMEmodule families, such as the MVME147S, MVME162, MVME167, MVME187, and MVME197, and their peripheral devices. An LCP
Summary of the content on the page No. 4
Although not shown in the above list, each Motorola Note Computer Group manual publication number is suffixed with characters which represent the revision level of the document, such as "/D2" (the second revision of a manual); a supplement bears the same number as the manual but has a suffix such as "/D1A1" (the first supplement to the manual). Manual Terminology Unless otherwise specified, throughout this manual all address references are in hexadecimal. An asterisk (*) following the sig
Summary of the content on the page No. 5
¨ Motorola and the Motorola symbol are registered trademarks of Motorola, Inc. VMEmodule is a trademark of Motorola, Inc. All other products mentioned in this document are trademarks or registered trademarks of their respective holders. © Copyright Motorola 1989, 1993, 1994 All Rights Reserved Printed in the United States of America August 1994
Summary of the content on the page No. 6
Safety Summary Safety Depends On You The following general safety precautions must be observed during all phases of operation, service, and repair of this equipment. Failure to comply with these precautions or with speciÞc warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the equipment. Motorola, Inc. assumes no liability for the customer's failure to comply with these requirements. The safety precautions listed below repres
Summary of the content on the page No. 7
! Dangerous voltages, capable of causing death, are present in WARNING this equipment. Use extreme caution when handling, testing, and adjusting. ! This equipment generates, uses, and can radiate radio WARNING frequency energy and if not installed and used in accordance with the documentation for this product, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A Computing Device pursuant to Subpart J of Part 15 of FCC rules, whi
Summary of the content on the page No. 8
Summary of the content on the page No. 9
Contents Introduction 1-1 Features of the MVME712 Family Modules 1-1 Features of the LCP2 Adapter Board 1-2 SpeciÞcations 1-2 Cooling Requirements 1-3 FCC Compliance 1-3 General Description 1-4 Introduction 2-1 Unpacking Instructions 2-1 MVME712x Module Preparation 2-1 DSR Line Pull Up Select Headers (J8, J9, J13, J14) 2-6 Serial Port 2/Modem Port 2 Select (J16, J17) 2-7 Serial Port Configuration 2-7 Modem Port Configuration 2-7 SCSI Termination 2-8 MVME712B Module Preparation 2-8 L
Summary of the content on the page No. 10
Parts Lists and Locations 3-22 Schematic Drawings 3-32 General Description A-1 Modem Features A-2 Technical SpeciÞcations A-3
Summary of the content on the page No. 11
List of Figures MVME712-12 Header Locations 2-2 MVME712-13 Header Locations 2-3 MVME712A Header Locations 2-4 MVME712AM Header Locations 2-5 MVME712B Connector Locations 2-9 LCP2 Adapter Connector Locations 2-10 Internal SCSI and Serial Port Connections 2-13 Internal SCSI and Modem Connections 2-15 MVME712B External SCSI Connections 2-17 MVME712-12 Parts Location Drawing (Primary Side) 3-24 MVME712-13 Parts Location Drawing (Primary Side) 3-25 MVME712A Parts Location Drawing (Primary Side)
Summary of the content on the page No. 12
GENERAL INFORMATION 1 Introduction This manual provides general information, hardware preparation, installation instructions, and support information for the MVME712A, AM, -12, -13, and B Transition Modules, as well as the LCP2 Adapter Board. The next table defines the references you will see throughout the manual. Collective Reference Modules Referred To MVME712 family all of the MVME712 MVME712-12 modules, including the MVME712-13 MVME712B MVME712A
Summary of the content on the page No. 13
General Information 1 o External Ethernet interface (through the LCP2 adapter) (MVME712B) o Built-in modem (refer to Appendix A) with front panel Telco modular jack (MVME712-13 and MVME712AM) o Electrostatic Discharge (ESD) protection on front panel o Radio Frequency Interference (RFI) protection on front panel Features of the LCP2 Adapter Board The features of the LCP2 Adapter Board include: o A 50-pin connector permits SCSI cable connection to other SCSI
Summary of the content on the page No. 14
Specifications 1 Cooling Requirements Motorola VMEmodules are specified, designed, and tested to operate reliably with an incoming air temperature range from 0 degrees C to 55 degrees C (32 degrees F to 131 degrees F) with forced air cooling. Temperature qualification is performed in a standard Motorola VMEsystem 1000 chassis. Twenty-five watt load boards are inserted in the two card slots, one on each side, adjacent to the board under test to simulate a high power density system co
Summary of the content on the page No. 15
General Information 1 General Description The MVME712 family modules are I/O transition modules for the MVME1xx VMEmodule families. The LCP2 adapter assembly routes the I/O signals and grounds from the P2 connector on the backplane at the MVME1xx VMEmodule to the MVME712 family module. The MVME712 family module routes the signals to the appropriate industry-standard connectors on its front panel. The MVME712-13 and MVME712AM both have a built-in modem. The MVME712x has four D
Summary of the content on the page No. 16
HARDWARE PREPARATION 2 AND INSTALLATION Introduction This chapter provides unpacking instructions, hardware preparation, and installation instructions for the MVME712 family modules and the LCP2 adapter. Unpacking Instructions If the carton is damaged upon receipt, request that carrier's Note agent be present during unpacking and inspection of equipment. Unpack equipment from shipping carton. Refer to packing list and verify that all items are present. Save
Summary of the content on the page No. 17
P2 A1 A32 B1 B32 12 C1 C32 J6 ETHERNET 20 16 2 J2 J10 J17 1 19 MODEM POWER U1 2 10 J9 J13 1 9 1 3 1 3 CR1 CR2 MODEM PORT + J16 C3 2 10 J8 J14 1 9 1 3 1 3 SERIAL PORT C1 C2 MODEM INTERCONNECT 20 2 MODEM PORT J7 J7 SERIAL PORT 1 SERIAL PORT 4 19 1 PRINTER PORT 24 13 15 15 15 15 13 1 J15 25 14 J12 69 69 69 69 J1 J3 J4 J5 SERIAL PORT 1 SERIAL PORT 2 SERIAL PORT 3 SERIAL PORT 4 PRINTER CONSOLE TTY01 1519 9408 Hardware Preparation and Installation MVME 712A/AM 2 DCE DCE DTE DTE DCE DCE DTE DTE Fi
Summary of the content on the page No. 18
P2 A1 A32 B1 B32 C1 C32 12 J6 ETHERNET 20 16 2 J2 J10 J17 19 1 MODEM POWER U1 2 10 J9 J13 1 9 1 3 1 3 CR1 CR2 MODEM PORT + J16 C3 2 10 J8 J14 1 9 1 3 1 3 SERIAL PORT C1 C2 MODEM INTERCONNECT 20 2 MODEM PORT J7 J7 SERIAL PORT 1 19 1 24 PRINTER PORT 13 13 1 15 15 15 15 J15 25 14 69 69 69 69 J12 J1 J3 J4 J5 SERIAL PORT 1 SERIAL PORT 2 SERIAL PORT 3 SERIAL PORT 4 PRINTER CONSOLE TTY01 cb221 9408 (2-3) MVME712x Module Preparation MVME 712A/12/13 2 DCE DCE DTE DTE DCE DCE DTE DTE Figure 2-2. MVME7
Summary of the content on the page No. 19
2 64 J11 1 63 12 J6 ETHERNET 20 16 2 J2 J10 J17 19 1 MODEM POWER U1 2 10 J9 J13 1 9 1 3 1 3 CR1 CR2 MODEM PORT + J16 C3 2 10 J8 J14 1 9 1 3 1 3 SERIAL PORT C1 C2 MODEM INTERCONNECT 20 2 MODEM PORT J7 J7 SERIAL PORT 1 SERIAL PORT 4 19 1 PRINTER PORT 24 13 13 1 15 15 15 15 J15 25 14 69 69 69 69 J12 J1 J3 J4 J5 SERIAL PORT 1 SERIAL PORT 2 SERIAL PORT 3 SERIAL PORT 4 PRINTER CONSOLE TTY01 cb221 9408 (1-3) Hardware Preparation and Installation MVME 712A/AM 2 DCE DCE DTE DTE DCE DCE DTE DTE Figure 2-3
Summary of the content on the page No. 20
2 64 J11 1 63 12 J6 20 16 2 J2 J10 J17 19 1 MODEM POWER U1 2 10 J9 J13 1 9 1 3 1 3 CR1 CR2 MODEM PORT + J16 C3 2 10 J8 J14 1 9 1 3 1 3 SERIAL PORT C1 C2 MODEM INTERCONNECT 20 2 MODEM PORT J7 J7 SERIAL PORT 1 19 1 PRINTER PORT 24 13 15 15 15 15 13 1 J15 J12 25 14 69 69 69 69 J1 J3 J4 J5 SERIAL PORT 1 SERIAL PORT 2 SERIAL PORT 3 SERIAL PORT 4 PRINTER CONSOLE TTY01 1520 9407 MVME712x Module Preparation MVME 712A/12/13 2 DCE DCE DTE DTE DCE DCE DTE DTE Figure 2-4. MVME712AM Header Locations MVME712
