Summary of the content on the page No. 1
*6816814H01*
6816814H01-G
Summary of the content on the page No. 2
0
Summary of the content on the page No. 3
Foreword This manual is intended for use by experienced technicians familiar with similar types of equipment. Specifically, it contains installation information required for the MOTOTRBO XPR 8300 Repeater. For information related to the service of the XPR 8300 Repeater, refer to the list applicable manuals available separately. This list is provided in the Related Publications section on page vii. Product Safety and RF Exposure Compliance See Installation Requirements for Compliance with Radio
Summary of the content on the page No. 4
Installation Requirements for Compliance with Radio Frequency (RF) Energy Exposure Safety Standards ATTENTION! This radio is intended for use in occupational/controlled conditions, where users have full knowledge of their exposure and can exercise control over their exposure to meet FCC limits. This radio device is NOT authorized for general population, consumer, or any other use. To ensure compliance to RF Energy Safety Standards: • Install only Motorola approved antennas and accessories • B
Summary of the content on the page No. 5
Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola, Inc. Address: 1301 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A. Phone Number: 1-888-567-7347 Hereby declares that the product: Model Name: XPR 8300 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15
Summary of the content on the page No. 6
Notes iv
Summary of the content on the page No. 7
Table of Contents v Table of Contents Foreword..........................................................................................................i Product Safety and RF Exposure Compliance.............................................................................................i Manual Revisions .........................................................................................................................................i Parts Ordering .......................................
Summary of the content on the page No. 8
vi Chapter 2 Mechanical Installation....................................................... 2-1 2.1 Unpacking Equipment....................................................................................................................2-1 2.2 Transferring Equipment from Shipping Container to Rack or Cabinet...........................................2-1 Chapter 3 Indicators and Connectors................................................. 3-1 3.1 Front Panel .......................................
Summary of the content on the page No. 9
List of Figures vii List of Figures Figure 4-1 Locations of Connectors on the Rear Panel of the Repeater ............................................... 4-1 Figure 4-2 Making Connections to a Backup Battery............................................................................. 4-2 Related Publications MOTOTRBO XPR 8300 Repeater Basic Service Manual ..........................................................6816810H01 Motorola Quality Standards Fixed Network Equipment Installation Manual R
Summary of the content on the page No. 10
viii List of Figures Notes March 2009 6816814H01
Summary of the content on the page No. 11
Repeater Model Numbering Scheme ix Repeater Model Numbering Scheme Model No.Example : AA M 2 7 Q P R 9 J A 7 A N Position : 1 2 3 4 5 6 7 8 9 10 11 12 Unique Model Variations AZ: Asia N: Standard Package LA: Latin America AA: North America (except Mexico) MD: Europe/Middle East/ Version Letter Africa/Australasia Repeater Feature Level 1: Mini-U MOTOTRBO Repeater 2: BNC Model Series 7: Rack Mount Band J : 136-174 MHz Q: 403-470 MHz T: 450-512 MHz Primary System Type A: Convent
Summary of the content on the page No. 12
x Repeater Model Numbering Scheme Notes March 2009 6816814H01
Summary of the content on the page No. 13
Commercial Warranty xi Commercial Warranty Limited Warranty MOTOROLA COMMUNICATION PRODUCTS I. What This Warranty Covers and For How Long MOTOROLA INC. (“MOTOROLA”) warrants the MOTOROLA manufactured Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below: XPR 8300 Repeater Two (2) Years Motorola, at its option, will at no charge either repair the Product (with new
Summary of the content on the page No. 14
xii Commercial Warranty III. State Law Rights SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. IV. How to Get Warranty Service You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to
Summary of the content on the page No. 15
Commercial Warranty xiii VI. Patent and Software Provisions MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following: A. that MOTOROLA will be noti
Summary of the content on the page No. 16
xiv Commercial Warranty Notes March 2009 6816814H01
Summary of the content on the page No. 17
Chapter 1 Pre-Installation Considerations Proper installation ensures the best possible performance and reliability of the MOTOTRBO Repeater. Pre-installation planning is required. This includes considering the mounting location of the repeater in relation to input power and antennas. Also consider the site environmental conditions, the particular mounting method (several available), and required tools and equipment. If this is the first time this type of equipment is being installed, it is
Summary of the content on the page No. 18
1-2 Pre-Installation Considerations Equipment Ventilation 1.2.3 Air Quality For equipment operating in an area which is environmentally controlled and with the repeater(s) rack mounted, the airborne particle level must not exceed 25 µg/m³. For equipment operating in an area which is not environmentally controlled and with the repeater(s) cabinet mounted, airborne particle level must not exceed 90 µg/m³. If the repeater is to be installed in an environment which is usually dusty, dirty, or do
Summary of the content on the page No. 19
Pre-Installation Considerations Site Grounding and Lightning Protection 1-3 1.6 Site Grounding and Lightning Protection Proper site grounding and lightning protection are vitally important considerations. Failure to provide proper lightning protection may result in !! permanent damage to the radio equipment. W A R N I N G One of the most important considerations when designing a communications site is the ground and lightning protection system. While proper grounding techniques and lightning
Summary of the content on the page No. 20
1-4 Pre-Installation Considerations Notes March 2009 6816814H01
