Summary of the content on the page No. 1
AS/400e 170 or 250
2809 or 2824 LAN/WAN
Workstation Card
Instruction
Version 4
SENG-2809-04
Summary of the content on the page No. 2
Summary of the content on the page No. 3
AS/400e 170 or 250 2809 or 2824 LAN/WAN Workstation Card Instruction Version 4 SENG-2809-04
Summary of the content on the page No. 4
Note Before using this information and the product it supports, be sure to read the “Safety and Environmental Notices” on page iii and the “Notices” on page 11. Fifth Edition (July 2000) This edition applies only to reduced instructions set computer (RISC) systems. © Copyright International Business Machines Corporation 1998, 2000. All rights reserved. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.
Summary of the content on the page No. 5
Safety and Environmental Notices Danger Notices A danger notice calls attention to a situation that is potentially lethal or extremely hazardous to people. DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the products that attach to the system. It is the customer’s responsibility to ensure that the outlet is correctly wired and grounded to prevent an electrical shock. (RSFTD201) DANGER To prevent a possible electrical shock whe
Summary of the content on the page No. 6
Laser Safety Information CAUTION: This product may contain a CD-ROM which is a class 1 laser product. (RSFTC240) Product Recycling and Disposal Components of the system, such as structural parts and circuit cards, can be recycled where recycling facilities exist. IBM does not currently collect and recycle used IBM products from customers in the United States other than those products that are involved in trade-in programs. Companies are available to disassemble, reutilize, recycle, or dispose of
Summary of the content on the page No. 7
Installation Instructions This feature is customer installed. It will take approximately 1 hour to install the hardware. However, you may elect not to perform this feature installation yourself. You may contact IBM or an Authorized Dealer to make arrangements for them to perform the feature installation for a fee. You need to allow additional time to complete your jobs, back up your system, IPL your system, and verify your hardware configuration. __ 1. When you use these instructions, you will d
Summary of the content on the page No. 8
When you have the following cards, install them in the sequence listed below. v The 2809 or 2824 LAN/WAN workstation card v The 285x or 2866 Integrated NetFinity cards v All other adapter cards Getting Ready __ 1. Ensure that all jobs are complete. __ 2. When all jobs are complete, type pwrdwnsys *immed on an AS/400 command line and press the Enter key. Note: Should you encounter difficulties during the installation, contact your authorized dealer or service provider. __ 3. When the AS/400 is co
Summary of the content on the page No. 9
Installing the 2809 or 2824 LAN/WAN Workstation Card __ 1. The adapter card slots are E02 through E14 in the expansion unit, (Figure 2). Slot E01 is not an available position. Figure 2. Adapter Card Positions __ 2. Remove the left side cover by removing the screws and sliding the cover from front to back until it stops. Pull the cover out (Figure 3 on page 4). Installation Instructions 3
Summary of the content on the page No. 10
Figure 3. Remove System Unit Side Cover Your system unit contains a battery that only trained personnel can replace. __ 3. CAUTION: The battery is a lithium battery. Only trained service personnel may replace this battery using the instructions in the Problem Analysis, Repair, and Parts service manual. To avoid possible explosion, do not burn or charge the battery. Exchange only with the IBM-approved part. Discard the battery as instructed by local regulations. (RSFTC241) __ 4. Attach the dispos
Summary of the content on the page No. 11
Figure 4. Attach Wrist Strap __ 5. You will be installing the 2809 or 2824 card in card slot E07. __ 6. Before you install the adapter card, remove the adapter card slot cover inside the system unit by doing the following: a. Remove the screw, (Figure 5 on page 6). b. Slide the slot cover out. Installation Instructions 5
Summary of the content on the page No. 12
Figure 5. Remove Slot Cover __ 7. Find the package that contains the new adapter card. Attention: Adapter cards are fragile: v Handle only by the edges v Keep fingers off printed circuit area v Use static strap when handling v Leave in protective packaging until ready to install Remove the adapter card from the electrostatic package. __ 8. Install the adapter card in the Expansion unit side of the system unit by doing the following: a. Align the adapter card with the card slot E07 (Figure 6 on p
Summary of the content on the page No. 13
Figure 6. Install Adapter Card __ 9. Do you have any other adapter cards or devices to install? No Yes ↓ If you know where to install the adapter card, follow the steps you just performed to install the card. If you do not know where to install the adapter card, go to the instructions that came with the adapter card. Look for the tables or steps that tell you where to install the adapter card and complete the installation. If you have another device such as a disk unit, a tape unit, or a memory
Summary of the content on the page No. 14
Figure 7. Install Side Cover Completing the Installation __ 1. Install the system unit back cover. __ 2. DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the products that attach to the system. It is the customer’s responsibility to ensure that the outlet is correctly wired and grounded to prevent an electrical shock. (RSFTD201) Plug the following power cords into an electrical outlet. v System unit v System unit console __ 3.
Summary of the content on the page No. 15
__ 4. Look at the Function/Data display on the control panel. Does a BN appear in the Function/Data display? Yes No ↓ Do the following: a. Press the Up or Down select push button until 02 appears in the Function/Data display. b. Press the Enter push button on the control panel. c. Press the Up or Down select push button until BN appears in the Function/Data display. d. Press the Enter push button on the control panel. e. Press the Up or Down select push button until 01 appears in the Function/Da
Summary of the content on the page No. 16
No Yes ↓ Verify that the card you moved is listed on the Packaging Hardware Resources menu. If a resource is missing (look for a ?) because an adapter card was moved, do the following: 1) On the line that has the question mark, type a 4 in the Opt column to remove the resource from the configuration. 2) Press the Enter key. 3) When Confirm Remove of Packaging Hardware Resources(s) appears, press the Enter key. 4) If you move an adapter card, or replace an adapter card with another adapter card,
Summary of the content on the page No. 17
Notices This information was developed for products and services offered in the U.S.A. IBM may not offer the products, services, or features discussed in this document in other countries. Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, o
Summary of the content on the page No. 18
If you are viewing this information softcopy, the photographs and color illustrations may not appear. The drawings and specifications contained herein shall not be reproduced in whole or in part without the written permission of IBM. IBM has prepared this publication for use by customer personnel for operating and planning for the specific machines indicated. IBM makes no representations that it is suitable for any other purpose. Electronic Emission Notices Federal Communications Commission (FCC
Summary of the content on the page No. 19
This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-IBM option cards. Australia and new Zealand Class A Statement Attention: This is a Class A product. In a domestic environment
Summary of the content on the page No. 20
14 AS/400e 170 or 250 2809 or 2824 LAN/WAN Workstation Card V4R5
