Summary of the content on the page No. 1
Hypertec BioDisk
Biodisk
Quick User Guide
User Guide
BioDisk from Hypertec - Quick User Guide
Summary of the content on the page No. 2
Table of Contents A. General Description A1. About BioDisk 2 A2. Partition Arrangement 2 A3. Autorun Feature 2 A4. Password & Finger Prints 2 B. How to swipe finger prints 3 C. System requirements 4 D. Getting started D1. Registering finger prints 5-7 D2. Setting security level and password 8-9 D3. Deleting finger prints and passwords 10 E. Finding the Device Serial Number 11 1 BioDisk from Hypertec - Quick User Guide
Summary of the content on the page No. 3
A. General Description A1. About the BioDisk What is the BioDisk? What does it do? The BioDisk is a USB Flash storage device with a finger print sensor, which allows you to use your own finger print as a security key instead of (or as well as) a password. Because everyoneÊs finger print is unique, the security level is much higher than with just a password-protect function. Be- sides raising the security level, there are many other benefits from using your finger print, including conven
Summary of the content on the page No. 4
B. How to Swipe Finger Prints B. How To Swipe Your Finger Print Step 1 Place your Biodisk on a flat surface. Make sure the USB connector is facing to the left. (see picture) Step 2 Make sure finger is clean and dry before swiping Step 3 Place your finger on top and to right hand side of the sensor Step 4 Press firmly down and swipe down across the sensor, keeping to the right hand edge. Take about 1-2 seconds to swipe your finger across the sensor. o Note: You may also rotate the BioDis
Summary of the content on the page No. 5
C. System Requirements C. System Requirements The following is the minimum system requirement for using the BioDisk: Pentium II 133MHz Processor or above 256MB or above RAM Microsoft Windows 2000 SP3 / Windows XP operating systems USB 1.1 or 2.0 8MB free hard space 4 BioDisk from Hypertec - Quick User Guide
Summary of the content on the page No. 6
D. Getting Started D1. Registering Finger Prints Step 1 When you first connect your Biodisk to your computerÊs USB Port, you will see the following screen: Step 2 Enter your User Name as you would like it to appear on screen 5 BioDisk from Hypertec - Quick User Guide
Summary of the content on the page No. 7
D. Getting Started D1. Registering Finger Prints (ctd) Step 3 The Finger Print set-up screen will come up automatically. Select an un-registered finger from the screen, the finger will be highlighted in green. Step 4 Once selected, you are asked to enrol a fingerprint. Press the finger firmly onto the sensor and swipe. Each swipe should last 1-2 seconds. Each finger print needs to be swiped successfully 3 consecutive times for enrolment to work. If successful, numbers 1,2,3 will
Summary of the content on the page No. 8
D. Getting Started D1. Registering Finger Prints (ctd) Step 5 Repeat until you are content with the number of fingerprints registered (all 10 prints can be registered if required). Enrolled fingers will be highlighted in blue. Step 6 When complete, click the button to continue. You will reach this screen: 7 BioDisk from Hypertec - Quick User Guide
Summary of the content on the page No. 9
D. Getting Started D2. Setting Security Level and Password Step 1 The drop down box allows you to choose the level of security protection for the Biodisk: FP Only (Fingerprint recognition only, no password required) Password and FP (Both password and fingerprint recognition are needed to access the Biodisk) Password or FP (Either one or the other can be used to access the drive). Step 2 If a Password-inclusive option is chosen, you will need to enter your chosen passwor
Summary of the content on the page No. 10
D. Getting Started D2. Setting Security Level and Password (ctd) Step 3 Once this step is complete, you will see the main menu screen: 9 BioDisk from Hypertec - Quick User Guide
Summary of the content on the page No. 11
D. Getting Started D3. Deleting Finger Prints and Passwords Step 1 On the main menu, choose ÂFP ManagerÊ. You will be asked to verify a fingerprint and/or password. Step 2 You will be asked to choose which finger you would like to delete (registered fingers are highlighted in blue). Tick to cancel registered print, or choose the cross to cancel operation. Step 3 To delete the need for a password, simply go to the security settings (see page 8), and select ÂFP onlyÊ, or ÂPassword or
Summary of the content on the page No. 12
E. Finding the Serial Number E. Finding the Device Serial Number To obtain the serial number of the Biodisk device for use with the reset tool FP_Init (which is downloadable from www.hypertec.co.uk under the „Downloads‰ section in „Technical Support‰): Use explorer to navigate to the CD partition of your Biodisk (referred to as partition 1 earlier in this document). You will then see the utility „Serial.exe‰. Execute this by double clicking and the serial number of the Biodisk will be dis
