Summary of the content on the page No. 1
TABLE OF CONTENTS
1.
1
1
4
? 6
2.
2.1. HARDWARE 1
2.2. SOFTWARE 2
2
3.
1
2
3.3. QUICK REFERENCE FOR JUMPERS & CONNECTORS 2
5
3.7. SPEAKER CONNECTOR INSTALLATION 7
3.8. HARDWARE RESET SWITCH CONNECTOR INSTALLATION 7
21
3- .......................
3- ........................ ................................
3-6 ................................ ................................ 3.6. CMOS RTC & ISA CFG CMOS SRAM
3- ........................... ................................ ........................
Summary of the content on the page No. 2
3.9. POWER LED CONNECTOR INSTALLATION 7 7 4. 4.1. ENTERING SETUP . 4.3. GETTING HELP . 4.5. STANDARD CMOS SETUP MENU 4.6. BIOS FEATURES SETUP 4.7. CHIPSET FEATURES SETUP 4.8. POWER MANAGEMENT SETUP 4.9. PNP/PCI CONFIGURATION 4.10. INTEGRATED PERIPHERALS 4.12. USER PASSWORD 4.13. IDE HDD AUTO DETECTION 4.15. EXIT WITHOUT SAVING 22 4-30 .................. ................................ ................................ 4-29 ........................ ................................ ...............
Summary of the content on the page No. 3
1. INTRODUCTION Welcome to use the motherboard. It is a Pentium II Processor based / be the fastest PC / AT system. There are some new features allow you to operate the system with just the performance you want. This manual also explains how to install the motherboard for operation, and how to set up your CMOS CONFIGURATION with BIOS SETUP program. q Intel Pentium II Processor based PC / AT compatible mainboard. q Slot 1 supports Pentium II processor running at 200-633 MHz. q Intel 44
Summary of the content on the page No. 4
1.3. PERFORMANCE LIST The following performance data list is the testing results of some popular benchmark testing programs. testing data values gotten by users. (The different Hardware & Software configuration will result in different benchmark testing results.) • Pentium II processor • • • GA-601 AGP Display Card (4MB SGRAM) • • O.S. Windows NT ™ 4.0 • Intel Pentium II Processor 266MHz(66x4) 333MHz(66x5) CPU mark32 721 864 FPU Winmark 1380 1720 Business Disk 2100 2140 Hi-End Disk 5260 5420
Summary of the content on the page No. 5
14.318MHz SLOT 1 AGP SLOT AGP Bus 14.318MHz USB Bus 14.318MHz I/O CHIPSET 3 1- PS/2 Mouse Keyboard Floppy Port ITE8671F LPT Port ISA Bus COM Ports CHIPSET IDE Bus USB Ports 82371EB PIIX4 48MHz 33MHz PCI Bus IDE Ports 52C64-05 24MHz Ultra DMA/33 PLL 33MHz 66MHz 66MHz 33MHz DRAM Bus CHIPSET 82443EX PAC Host Bus DIMM Sockets 3.3V EDO/SDRAM 1.4. BLOCK DIAGRAM 66MHz 6EA
Summary of the content on the page No. 6
â 1.5. INTRODUCE THE Pentium Figure 2:OEM Pentium II Processor 4 1- Figure 1:Retention Mechanism & attach Mount II Processor Introduction
Summary of the content on the page No. 7
Figure 3:Heatsink / FAN & Heat sink support for OEM Pentium II Processor II Processor & Heat sink support 5 1- Figure 4:Boxed Pentium 6EA
Summary of the content on the page No. 8
? device that supports an AGP port. The main purpose of the AGP port is to provide fast access to system memory. at 33MHz) or as an AGP port which supports 2x data-rate, a read queue, and – transmit the data address on a separate line in order to speed up the transaction. 6 1- removing the effects of the reads-latency. Side band addressing can be used to at 533MB/sec (66.6*2*4). The read-queue can be used to pipeline reads side band addressing. When the 2x-data rate is used the port can transmi
Summary of the content on the page No. 9
2. • CPU - Pentium II processor 200 – - 242 pins 66MHz slot1 on board. • - - - - • - 2 banks 168 pins DIMM module sockets on board. - Use 8 / 16 / 32 / 64 / 128 / 256 MB 50~60 - - - - 32 KB 1st cache memory included in CPU. • - - • I/O BUS SLOTS - - 2 8MHz 16 bits ISA BUS. - • IDE PORTS - board.(Using IRQ14,15) - – ROM. - Supports 2 16550 COM ports. • I/O PORTS - Supports 1 EPP/ECP LPT port. - Supports 1 1.44/2.88 MB Floppy port. - Supports 2 USB ports. - 1 2- Supports PS/2 Mouse & Keyboard
Summary of the content on the page No. 10
- Suspend mode support. • GREEN FUNCTION - Green switch & ACPI LED support. - IDE & Display power down support. - Monitors all IRQ / DMA / Display / I/O events. • - - Supports Plug & Play, DMI Function. • - Baby AT Form Factor, 4 layers PCB. • - Bus Master IDE Driver. - Suspend to HD utility. • BIOS - Licensed AWARD BIOS. - Setup, Hard Disk Utility included. • O.S. - Operation with MS-DOS , Windows 95, WINDOWS NT, OS/2, NOVELL and SCO UNIX. 2.3. ENVIRONMENT • Ambient Temp. - 0 ° C to +50 °
Summary of the content on the page No. 11
3. mainboard package should contain the following: • main board. • • • Cable set for IDE, Floppy & I/O devices. • CD for main board Utility. (Bus Master IDE Driver, Suspend to HD Utility, LDCM, SIV, Patch 95) The main board contains sensitive electric components, which can be easily damaged by static electricity, so the main board should be left in its original packing until it is installed. operator should be wearing an anti static wristband, grounded at the same point as the anti-static mat.
Summary of the content on the page No. 12
SOFT PWR GN TD TB HD USB WAKE ON SW 1 JP4 JP3 JP2 SB-LINK IDE 1 IDE 2 PWR CPU POWER × Ø t I/O Ports Connector USB port. For Primary IDE port. For Secondary IDE port. For Keyboard port. For Floppy port Y For Serial port2 (COM B). For Serial port1 (COM A). For LPT port. t Slot 1 For Pentium II Processor installed 2 3- LPT COMA COMB FLOPP For PS/2 Mouse port. PS/2 KB IDE2 IDE1 USB 3.3. QUICK REFERENCE FOR JUMPERS & CONNECTORS Figure 3.1 JP1 ATX POWER KB FLOPPY LPT COM B FAN 82443LX Intel 440EX
Summary of the content on the page No. 13
t IR : INFRARED Connector (IR) -- Function Option Pin No. Function 1 IR Data Output 2 3 IR Data Input 4 Signal 5 POWER (+) t PWR : POWER ON LED ( PW-LED) Pin No. Function 1 LED POWER (+) 2 LED POWER (-) 3 LED POWER (-) t Pin No. Function 1 2 3 4 Signal t TD : Turbo LED Connector Pin No. Function 1 LED POWER (+) 2 LED POWER (-) t RST : RESET Switch Pin No. Function 1 2 t GN : GN-SW Pin No. Function 1 2 t HD : Hard Disk active LED (HD-LED) Pin No. Function 1 LED POWER (+) 2 LED POWER (-) 3 3-
Summary of the content on the page No. 14
t Soft PWR : Soft Power Switch Pin No. Function 1 2 t FAN PWR : CPU cooling FAN Power Connector Pin No. Function 1 GND. 2 3 t J10 : System After Ac Back Pin No. Function Soft Off. Full On. t Pin No. Function 1-2 2-3 t Wake on Pin No. Function 1 2 3 Signal t SB-LINK : For PCI Audio / Sound Card use only Pin No. Function 1 Signal 2 3 4 Signal 5 6 Signal 4 3- GND NC GND GND +5V SB Lan Disabled Keyboard power on. Enabled Keyboard power on. JP1 : Keyboard Power On Selection 1-2 Close 1-2 Open
Summary of the content on the page No. 15
The main board can be installed with 8 / 16 / 32 / 64 / 128 / 256 MB 168 pins DIMM module DRAM, and the DRAM speed must be 50 or 60 ns for EDO & 67MHz for SDRAM when system bus speed is set to 66MHz. The DRAM memory system on main board consists of bank 0 and bank 1 . Since 168 pins DIMM module is 64 bits width, therefore 1 piece of DIMM DIMM module into the DIMM socket at Vertical angle. If there is a wrong direction of Pin 1, the DRAM DIMM module could not be inserted into socket completely.
Summary of the content on the page No. 16
DIP SWITCH (SW) FREQ. EXT.CLK. RATIO 1 2 3 4 4 5 M The CPU is a sensitive electric component and it can be easily surface when the CPU is installed onto main board. 3.6. CMOS RTC & ISA CFG CMOS SRAM There're RTC & CMOS SRAM on board; they have a power supply from external battery to keep the DATA inviolate & effective. The RTC is a REAL- SRAM is used for keeping the information of system configuration, so the system can automatically boot OS every time. Since the lifetime of internal c
Summary of the content on the page No. 17
3.7. SPEAKER CONNECTOR INSTALLATION There is a speaker in AT system for sound purpose. The 4 - Pins connector by user. The RESET switch is a 2 PIN connector and should be installed to on main board. 3.9. POWER LED CONNECTOR INSTALLATION off or flash to indicate which step on the system. The connector should be of main board in a correct direction. 3.10. IDE & ATAPI DEVICE INSTALLATION in a system. The HD is the active LED port for ATAPI devices. After the I/O device installation and jumper
Summary of the content on the page No. 18
Summary of the content on the page No. 19
