Summary of the content on the page No. 1
FUJITSU PCI Gigabit Ethernet
4.1 Update2 / 5.0
for Oracle Solaris
User's Guide
Solaris
C120-E276-11ENZ0(A)
October 2011
SPARC Enterprise
Summary of the content on the page No. 2
Preface Purpose This manual describes how to install the Gigabit Ethernet card into your SPARC Enterprise system, and configure the environmental settings for the interface. Target Reader This manual is intended for system administrators responsible for installing the Gigabit Ethernet card. To understand the concepts and procedures presented in this manual, you need a few years of experience in Oracle Solaris (in this manual, abbreviated to Solaris) system administration and have a basic kno
Summary of the content on the page No. 3
Note - This symbol indicates that important information is given. Information - This symbol indicates that useful information is given. Handling of This Manual This manual contains important information regarding the use and handling of this product. Read this manual thoroughly. Pay special attention to the section "Important Warnings". Use the product according to the instructions in this manual. FUJITSU makes every effort to prevent users and bystanders from being injured or from sufferi
Summary of the content on the page No. 4
Edition Date Details Support switches was added Changed the Version 2.1 to 2.2 Quad Gigabit Ethernet card(PW008QG1) was supported 05 2005-11-11 Changed the Version 2.2 to 2.3 RoHS compliant 1port Gigabit Ethernet Card(PW0G8GE1, PW0G8GE2) was supported 06 2006-2-06 Changed the Version 2.3 to 2.4 PCI Express Gigabit Ethernet Card(SE0X7GD1X, SE0X7GD2X, SE0X7CQ1X) was supported 07 2007-1-20 Changed the Version 2.4 to 3.0 08 2007-4-03 Changed the Version 3.0 to 3.0 Update1 GLDv3(The LinkAggregation F
Summary of the content on the page No. 5
Contents Chapter 1 Product Outline........................................................................................................................................................1 1.1 Key Features........................................................................................................................................................................................1 1.2 Gigabit Ethernet Card Specifications......................................................................
Summary of the content on the page No. 6
D.3 Notes.................................................................................................................................................................................................69 Appendix E Using FUJITSU PCI GigabitEthernet in Oracle VM Server for SPARC..............................................................73 E.1 Oracle VM Server for SPARC Support......................................................................................................................
Summary of the content on the page No. 7
Chapter 1 Product Outline This chapter describes the following topics. - 1.1 Key Features - 1.2 Gigabit Ethernet Card Specifications 1.1 Key Features The Gigabit Ethernet cards covered in this manual are adapters designed for Solaris servers that are connected to a Gigabit Ethernet network. These cards provide the physical services and data link services defined by IEEE802.3, and are designed to work in a framework of the open system architecture used widely now. These cards are integrated under
Summary of the content on the page No. 8
The GLDv3 compliant driver works with the following features. - The LinkAggregation (based on IEEE 802.3) by the dladm(1M) command. - Solaris Containers (Exclusive-IP Non-Global Zones) - Oracle VM Server for SPARC The GLDv3 compliant driver does not work with the following features. - SNA/FNA - The Multipath Function of PRIMECLUSTER GLS. The following feature was changed. - Set instance number by ndd(1M) command. Solaris 11 Network Virtualization New features, Vanity Naming and Environment Set
Summary of the content on the page No. 9
Item Hardware Specification Maximum: 9.1W (SE0X7GD1X), 9.2W (SE0X7GD2X), Power Requirements 15.0W (SE0X7GQ1X), 12.8W (SE0X7GQ2X) 1000Base-SX (SE0X7GD2X): Multi-mode Fibre LC-SC: 62.5/125 micron and 50/125 micron (Card side is LC. Used when connecting to a device with an SC connector.), LC- Connections LC: 62.5/125 micron and 50/125 micron 10/100/1000Base-T (SE0X7GD1X, SE0X7GQ1X, SE0X7GQ2X): CAT5e Cable (CAT5 cable can also be used for 10/100Mbps.) Note - SE0X7GD2X only support full duplex con
Summary of the content on the page No. 10
Figure 1.1 1000Base-SX * 2ports (SE0X7GD2X) Figure 1.2 10/100/1000Base-T * 2ports (SE0X7GD1X) - 4 -
Summary of the content on the page No. 11
Figure 1.3 10/100/1000Base-T * 4ports (SE0X7GQ1X) Figure 1.4 10/100/1000Base-T * 4ports (SE0X7GQ2X) - 5 -
Summary of the content on the page No. 12
Chapter 2 Gigabit Ethernet Card Installation This chapter describes the tasks necessary to install this card in your system. Install the hardware with the following procedures. - 2.1 Installation of the Gigabit Ethernet Card - 2.2 Identifying the Gigabit Ethernet Card - 2.3 Cable Connection 2.1 Installation of the Gigabit Ethernet Card Insert the card into a PCI Express slot on your server. Please refer to the User's Manual of your server for details about installing cards and specific PCI Expre
Summary of the content on the page No. 13
Figure 2.1 SE0X7GD2X (with Multimode Optical Fiber Cable) - 7 -
Summary of the content on the page No. 14
Figure 2.2 SE0X7GD1X (with Twisted Pair CAT5e Cable) - 8 -
Summary of the content on the page No. 15
Figure 2.3 SE0X7GQ1X (with Twisted Pair CAT5e Cable) - 9 -
Summary of the content on the page No. 16
Figure 2.4 SE0X7GQ2X (with Twisted Pair CAT5e Cable) - 10 -
Summary of the content on the page No. 17
Chapter 3 Setting Instructions This chapter describes the summary of environment settings required after installing this product. Install the driver and configure environment settings using the following procedures. - 3.1 Driver Software Installation - 3.2 Identification of Interface Name - 3.2 Identification of Interface Name - 3.3 Environment Setting - 3.5 Operation Mode Setup - 3.6 Network Installation - 3.7 VLAN Interface Setup 3.1 Driver Software Installation It is necessary to install the
Summary of the content on the page No. 18
3.3 Environment Setting This section explains how to edit the necessary files and use the commands(Solari 11 only) to configure the operating environment for each FUJITSU PCI GigabitEthernet interface. For TCP/IP (IPv4 or IPv6), edit the following files and execute the following command(Solaris 11 only). - Solaris 10 8/07 or later - /etc/hostname.fjgi* (*1) file - /etc/inet/hosts file or /etc/inet/ipnodes file - /etc/inet/netmasks file *1: Please put a decimal number (instance number) in place o
Summary of the content on the page No. 19
3. Edit the /etc/inet/netmasks file Describe the relationship between the network address and the netmask in the /etc/inet/netmasks file. Example of the /etc/inet/netmasks file: Describe the relationship between the network address (example: 192.168.150.0) and the netmask (example: 255.255.255.0). # Network Address netmask 192.168.150.0 255.255.255.0 4. Reboot the system Reboot the system after editing the above files. - Solaris 11 1. How to Use the ipadm(1M) Command Assign an
Summary of the content on the page No. 20
3.3.2 Environment Setting of IPv6 Interfaces - Solaris 10 8/07 or later 1. Edit the /etc/hostname6.fjgi* file Assign an IPv6 address or hostname and prefix length to the fjgi interface by editing the /etc/hostname6.fjgi* file (where fjgi* represents the driver name and instance number). Example of the /etc/hostname6.fjgi* file: Define a unique hostname (example: giga-v6) and prefix length (example: 120). (*1) addif giga-v6/120 up Or define an IPv6 address (example: fe80::2e0:ff:fea6:2222) and pr
