Summary of the content on the page No. 1
User’s Guide
DVI 104 Tx/Rx
DVI Fiber Optic Extender
68-1549-01
Rev. C
10 08
Summary of the content on the page No. 2
Precautions Safety Instructions • English Warning Power sources • This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor. The third (grounding) pin is a safety the literature provided with the equipment. feature, do not attempt to bypass or disable it.
Summary of the content on the page No. 3
警告 安全须知 • 中文 电源 • 该设备只能使用产品上标明的电源。 设备 这个符号提示用户该设备用户手册中 必须使用有地线的供电系统供电。 第三条线 有重要的操作和维护说明。 （地线）是安全设施，不能不用或跳过。 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 这个符号警告用户该设备机壳内有暴 或桌面电源的电源线，或任何接到市电系统的电源线。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 露的危险电压，有触电危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 注意 没有用户可以更换的零件。为避免出现触电危险不要自 阅读说明书 • 用户使用该设备前必须阅读并理 己试图打开设备盖子维修该设备。 解所有安全和使用说明。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 保存说明书 • 用户应保存安全说明书以备将来使 机内敏感元件过热。 不要用任何东西挡住通风孔。 用。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 遵守警告 • 用户应遵守产品和用户指南上的所有安 与厂家推荐的相同或相近型号的电池。 按照生产厂的 全和操作说明。 建议处理废弃电
Summary of the content on the page No. 4
Summary of the content on the page No. 5
DVI 104 Tx/Rx Description The DVI 104 Tx and DVI 104 Rx are fiber optic transmitter/ receiver units that extend DVI signals up to 1,640' (500 m) using four multimode fiber optics cables. The transmitter plugs directly into the source device and the receiver plugs directly into the display device. The transmitter/receiver pair can handle DVI video signals with resolutions up to 1920 x 1200 or 1080p @ 60 Hz. Optional four-fiber multimode cables are available in varying lengths. PC with DVI Out
Summary of the content on the page No. 6
DVI 104 Tx/Rx, cont’d Features Power Supply — Separate power supplies are provided for both the transmitter and receiver. Power LEDs — The LEDs are on the top and bottom panels of both the receiver and transmitter. They illuminate blue when the unit is receiving power. No mounting hardware required — The units plug directly into the source device (transmitter) or output device (receiver) and take up very little space. EDID Minder — The DVI 104 transmitter is able to capture and store the
Summary of the content on the page No. 7
LC Jacks — Four fiber optic cables connect the transmitter to the b receiver. The cables connect to the four female LC jacks in each of the units. A label on the top panel identifies the unit as the transmitter or receiver and identifies the fiber optic port numbers and the power input. For the transmitter, port 1 is closest to the power input N and port 4 is furthest away. For the receiver, port 4 is closest to the power input and port 1 is furthest away. Although the orientation
Summary of the content on the page No. 8
DVI 104 Tx/Rx, cont’d Rear panel features 13 68 3 Male Connector 9 17 19 22 24 A single-link DVI-D male connector is used to connect the c transmitter to the source and the receiver to the output device. Pin Signal Pin Signal Pin Signal 1 TMDS data 2- 9 TMDS data 1- 17 TMDS data 0- 2 TMDS data 2+ 10 TMDS data 1+ 18 TMDS data 0+ 3 TMDS data 2 11 TMDS data 1 19 TMDS data 0 shield shield shield 6 DDC clock 14 +5 V power 22 TMDS clock shield 7 DDC data 15 Ground (+5V) 23 TMDS clock+ 8 CEC contro
Summary of the content on the page No. 9
www.extron.com www.extron.com Label — a label on the top panel identifies the unit as the f transmitter (Tx, left panel of the figure below) or receiver (Rx, right panel of the figure below) and also identifies the fiber optic port numbers and the power input. Extron Extron 33-1641-01 33-1642-01 Rev. A 05 08 Rev. A 05 08 TO COMPUTER (Tx) TO DISPLAY (Rx) PN 60-977-12 PN 60-977-13 5 V 123 4 5 V 432 1 Bottom panel features The bottom panels of both the transmitter and receiver have a label t
Summary of the content on the page No. 10
DVI 104 Tx/Rx, cont’d Setup and Operation When using the DVI 104 Tx/Rx for the first time or if the display device is changed, it is essential to set up the EDID Minder. The setup process places EDID information on a EEPROM chip in the transmitter, which allows the video source to boot up correctly. This process is described below in steps 1-6. If you have already set up the EDID Minder, proceed to step 7. 1. Ensure that the source, the display, the transmitter, and the receiver are all
Summary of the content on the page No. 11
www.extron.com www.extron.com Extron 33-1642-01 Rev. A 05 08 TO DISPLAY (Rx) PN 60-977-13 5 V 4 3 2 1 Extron 33-1641-01 Rev. A 05 08 TO COMPUTER (Tx) PN 60-977-12 5 V 1 2 3 4 7. Apply power to the receiver by inserting the cable from the external power supply into the input jack. The LEDs should illuminate a solid blue. 8. Ensure that the display device is still powered on, connect the receiver directly to the DVI input, and tighten the thumbscrews. 9. Ensure that the PC or source is powe
Summary of the content on the page No. 12
DVI 104 Tx/Rx, cont’d Trouble Shooting Display does not show an image • Ensure that all plugs and jacks used by the external power supplies are firmly connected. If the cable is loose or slips out of the slot easily, move the release catch from its normal position above the locking catch, to the adjusted position under the locking catch (see the figure below). This provides the extra leverage required to keep the locking catch in place and hold the cable securely. Locking catch Release c
Summary of the content on the page No. 13
• Ensure that the transmitter is firmly plugged into the source device and the receiver is firmly plugged into the output device. • Try resetting the system by unplugging and reconnecting the DVI connectors or the power jacks. • Try rebooting the computer. Screen is distorted or displays noise • Ensure that the cable length does not exceed 1,640' (500 m). • Ensure that the cables are high quality multimode cable and are terminated with securely fitting plugs. • Ensure that the graphic reso
Summary of the content on the page No. 14
DVI 104 Tx/Rx, cont’d Specifications The DVI 104 TX/RX consists of a transmitter (DVI 104 TX) N and a receiver (DVI 104 RX) with fiber optic cables linking the two units. These transceivers are Class 1 laser products. They meet the N safety regulations of IEC-60825, FAD 21, CFR 1040.10, and FDA 21 CFR 1040.11. Optical fiber interconnection between transmitter and receiver Number/type ................................ 4 fiber optic, multimode Connectors ...................................
Summary of the content on the page No. 15
Cooling ........................................... Convection, no vents Mounting Rack mount ........................ No Furniture mount ................ No Enclosure type .............................. Plastic Enclosure dimensions .................. 0.6" H x 1.5" W x 2.3" D (1.5 cm H x 3.9 cm W x 5.9 cm D) (Depth excludes DVI connector.) Product weight .............................. 0.7 lbs (0.3 kg) per TX/RX pair Shipping weight ............................ 1 lb (<1 kg) per TX/RX pair Vi
Summary of the content on the page No. 16
DVI 104 Tx/Rx, cont’d Parts Included parts Included Parts Replacement part number DVI 104 Tx/Rx 60-977-01 DVI 104 Tx 60-977-12 DVI 104 Rx 60-977-13 (2) 5 VDC Power Supply DVI 104 Tx/Rx User’s Guide Fiber optic cables Accessories Part number 4-fiber MM LC-LC - 10 m (33') 26-652-01 4-fiber MM LC-LC - 20 m (66') 26-652-02 4-fiber MM LC-LC - 30 m (98') 26-652-03 4-fiber MM LC-LC - 40 m (131') 26-652-04 4-fiber MM LC-LC - 50 m (164') 26-652-05 4-fiber MM LC-LC - 60 m (197') 26-652-06 4-fiber MM LC-L
Summary of the content on the page No. 17
DVI 104 Tx/Rx • User’s Guide 13
Summary of the content on the page No. 18
14 DVI 104 Tx/Rx • User’s Guide
Summary of the content on the page No. 19
Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned with
Summary of the content on the page No. 20
Extron USA - West Extron USA - East Extron EMEA Extron Asia Extron Japan Extron China Extron Middle East Headquarters +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +400.883.1568 +971.4.2991800 Inside USA / Canada Only Inside Europe Only Inside Asia Only Inside China Only +800.633.9876 +81.3.3511.7656 FAX +971.4.2991880 FAX Inside USA / Canada Only +1.919.863.1794 +31.33.453.4040 +65.6383.4400 +86.21.3760.1568 +1.714.491.1500 +1.919.863.1797 FAX +31.33.453.4050 FAX +65.6383.4664 FAX
