Summary of the content on the page No. 1
Display Attached Controller
@E.Terminal for MC
USER'S MANUAL
Hardware
FEH300b
Summary of the content on the page No. 2
Preface This hardware edition of the user’s manual describes system composition, specifications, and handling of the @E.Terminal. In order to operate the hardware properly, please read this user’s manual carefully. When using modules or peripheral devices, be sure to read the corresponding user’s manuals listed below. Title Manual No. Contents @E.Terminal for MC FEH301 Describes functions and the usage of motion control User's Manual content for @E.Terminal for MC. V8 series Hardware
Summary of the content on the page No. 3
Safety Precautions Be sure to read the “Safety Precautions” thoroughly before using the module. Here, the safety precaution items are classified into “Warning” and “Caution.” : Incorrect handling of the device may result in death or serious injury. Warning Caution : Incorrect handling of the device may result in minor injury or physical damage. Even some items indicated by “Caution” may also result in a serious accident. Both safety instruction categories provide important information. Be sure t
Summary of the content on the page No. 4
Safety Precautions Caution ◊ Check the appearance of the unit when it is unpacked. Do not use the unit if any damage or deformation is found. Failure to do so may lead to fire, damage or malfunction. ◊ For use in a facility or for a system related to nuclear energy, aerospace, medical, traffic equipment, or mobile installations, please consult your local distributor. ◊ Operate (or store) @E.Terminal under the conditions indicated in this manual and related manuals. Failure to do so coul
Summary of the content on the page No. 5
Safety Precautions [General Notes] • Never bundle control cables nor input/output cables with high-voltage and large-current carrying cables such as power supply cables. Keep these cables at least 200 mm away from the high-voltage and large-current carrying cables. Otherwise, malfunction may occur due to noise. • When using @E.Terminal in an environment where a source of high-frequency noise is present, it is recommended that the FG shielded cable (communication cable) be grounded at its ends. H
Summary of the content on the page No. 6
Revisions *Manual No. is shown on the cover. Printed on *Manual No. Revision contents Aug. 2008 FEH300 First edition Nov. 2008 FEH300a • Display part is changed from UG40 series to V8 series. • Accessory "Noise filter" is eliminated from controller hardware version "03" or later. Dec. 2008 FEH300b @E.Terminal (No contents installed) was added.
Summary of the content on the page No. 7
Contents Preface Safety Precautions Revisions Contents Page Section 1 General ..........................................................................................1-1 1-1 Overview of @E.Terminal for MC .................................................................................................. 1-1 1-2 Appearance ..................................................................................................................................... 1-2 1-3 Types .......................
Summary of the content on the page No. 8
Section 1 General Page 1-1 Overview of @E.Terminal for MC............................................................................... 1-1 1-2 Appearance ................................................................................................................. 1-2 1-3 Types ............................................................................................................................ 1-3 1-4 System Composition ...........................................................
Summary of the content on the page No. 9
Section 1 General 1-1 Overview of @E.Terminal for MC The @E.Terminal for MC Display Attached Controller is an all-in-one programmable operation display and motion controller. Features: 1) The guidance function of the display screen allows you to easily set up parameters and positioning data previously set up by a dedicated machine. Also, it enables easy equipment maintenance. 2) The SX bus allows one-touch connection of up to eight servo amplifiers (axes) (FALDIC-α and APLHA5 VS type), minimiz
Summary of the content on the page No. 10
1-2 Appearance @E.Terminal for MC is composed of a programmable operation display (the display unit) and a controller unit attached to the back of the display unit. The controller unit is attached with screws to the connector area of the communication unit at the back of the display unit, similar to the way in which the communication unit is attached. Type 12 Controller unit Type 10 Side Display unit Type 8 Controller unit CN7 CN5 ONL SX-BUS ERR Front UROM IN RUN ALM BAT 4:RUN 3:U-TERM 2:TERM 1
Summary of the content on the page No. 11
1-3 Types • @E.Terminal for MC Product types Display size Specifications NP5M0101-5H4 12.1 inches • TFT color, 800 x 600 dots, DC power supply • Controller unit NP5M0101-4H4 10.4 inches • Contents of the motion control (Screen data, built in software in the controller) NP5M0101-3H4 8.4 inches • @E.Terminal (No contents installed) Product types Display size Specifications NP5N0011-5H4 12.1 inches • TFT color, 800 x 600 dots, DC power supply • Controller unit NP5N0011-4H4 10.4 inches • No content
Summary of the content on the page No. 12
1-3 Types • Auxiliaries and others Names Types Specifications Battery for display unit V7-BT Replacement lithium primary battery for the V8 series Replacement backlight for V812-FL Replacement backlight for V812 TFT TFT V810-FL Replacement backlight for V810S TFT V808S-FL Replacement backlight for V808S TFT Battery for controller NP8P-BT Primary lithium battery for memory data backup for controller unit SX bus terminating plug NP8B-BP For SX bus loop terminating (1 piece) SX bus expansion cabl
Summary of the content on the page No. 13
1-4 System Composition The following illustration shows the system composition of @E.Terminal for MC. PLC/general purpose computer Ethernet/RS-232C or RS-485 LAN/CN1/MJ1/MJ2 USB-B Up to 8 servos and I/O terminals each can be connected. SX bus MJ1/MJ2 "V-CP" Screen editor "V-SFT-5" External PG @E.Terminal for MC (V5.3.0.0 or later) (only No. 1 axis) FALDIC ALPHA5 [No. 1 axis] FALDIC - α SX bus station No.: "201" "NW0H-CNV + NW0H-CA3" or commercially available USB cable [No. 2 axis] S
Summary of the content on the page No. 14
Section 2 Specifications Page 2-1 Specifications.............................................................................................................. 2-1 2-1-1 General specifications ........................................................................................................... 2-1 2-1-2 Display unit specifications ..................................................................................................... 2-2 (1) Display unit specifications ......................
Summary of the content on the page No. 15
Section 2 Specifications 2-1 Specifications 2-1-1 General specifications Items Specifications NP5M0101-5H4 NP5M0101-4H4 NP5M0101-3H4 NP5N0011-5H4 NP5N0011-4H4 NP5N0011-3H4 Physical Operational ambient 0to+50 °C environmental temperature conditions Storage ambient -10 to +60 °C temperature Operational ambient 85 % RH or less humidity (Without dew condensation, max. wet-bulb temperature: 39 °C or less) Operational altitude 2000 m or less above sea level (Transport condition: 70 kPa or more) Oper
Summary of the content on the page No. 16
2-1 Specifications 2-1-2 Display unit specifications (1) Display unit specifications NP5M0101-5H4 NP5M0101-4H4 NP5M0101-3H4 Item NP5N0011-5H4 NP5N0011-4H4 NP5N0011-3H4 Display device TFT color Display size 12.1-inch 10.4-inch 8.4-inch Colors 65,536 colors (without blinks) / 32,768 colors (with blinks) Display resolution (W x H) 800 x 600 dots Dot pitch (W x H) 0.3075 x 0.3075 mm 0.264 x 0.264 mm 0.2135 x 0.213 mm Backlight Cold cathode tube Backlight life Approx. 50,000 hours (at the normal tem
Summary of the content on the page No. 17
2-1 Specifications (4) Interface specifications Item Specifications D-sub 9-pin (CN1) Applicable RS-232C, RS-422/485 standards Synchronization Asynchronous type Data length 7- or 8-bit Parity None, odd, even Stop bit 1- or 2-bit Baud rate 4800, 9600, 19200, 38400, 57600, 76800, 115.2kbps (187500 bps for MPI connection (Note)) Applications PLC, temperature controller, barcode reader, etc. Modular jack 8-pin Applicable RS-232C, RS-485 (2-wire connection) (MJ1/MJ2) standards Applications Screen da
Summary of the content on the page No. 18
2-1 Specifications (6) Drawing environment Item Specifications Drawing method Exclusive configuration software Drawing tool Name of exclusive configuration software: V-SFT-5 Personal computer: Pentium III 800 MHz or above (Pentium IV 2.0 GHz or above recommended) OS: Windows98SE/NT4.0/Me/2000/XP/XP64 Edition/Vista 32-bit Capacity of hard disk required: Free space of approx. 850 Mbytes or more Display: Resolution 1024 x 800 or above Screen color: 16 bits or more (7) Display function specificatio
Summary of the content on the page No. 19
2-1 Specifications (8) Function performance specifications Item Specifications Screens Max. 1024 Screen memory Flash memory: Approx. 12.5 Mbytes (Varies depending on the font) Switch 1024 per screen Switch actions Set, reset, momentary, alternate, to light (Possible to press a function switch and a switch on the display at the same time) Lamp Reverse, blink, exchange of graphics 1024 per screen Graph Pie, bar, panel meter and closed area graph:No limitation Statistics and trend graphs: Max. 256
Summary of the content on the page No. 20
2-1 Specifications 2-1-3 Controller unit specifications (1) Application performance specifications Item Specifications Type NP5M0101-5H4/4H4/3H4 NP5N0011-5H4/4H4/3H4 Control system Stored program, Cyclic scanning system (default task), periodic task, event task Input / Output connection method Direct input / output (SX bus) I/O control system Via SX bus: Synchronous refresh with takt CPU 32-bit RISC processor Memory types Program memory, data memory, temporary memory Programming language
