Summary of the content on the page No. 1
DIVA T/A ISDN Modem
User’s Guide
International
Summary of the content on the page No. 2
Third Edition (July 1999) 206-269-03 DIVA T/A ISDN Modem is a trademark of Eicon Technology Corporation. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. CompuServe is a registered trademark of CompuServe Incorporated. Hayes is a registered trademark of Hayes Microcomputer Products, Inc. Changes are periodically made to the information herein; these changes will be incorporated into new editions of the publication. Eicon Technology may make imp
Summary of the content on the page No. 3
Contents Introduction .......................................................................................................................................... 5 Installation Requirements ................................................................................................................... 6 Connecting the Cables to the DIVAT/A ............................................................................................... 7 Windows 95/98/NT Installation and Setup ..................
Summary of the content on the page No. 4
Contents Multiple Subscriber Numbering ...................................................................................................... 120 Assigning Primary and Secondary Numbers to the Phone Ports ................................................................121 Configuring a Port to Answer Any Number no tConfigure dElsewhere ...................................................123 Specifying what numbers the data port should answer .......................................................
Summary of the content on the page No. 5
Introduction The DIVA T/A is an external ISDN modem available in S/T and U interface versions. It provides easy and affordable access to the Internet via ISDN. With the DIVA T/A, Small Office Home Office (SOHO) users and telecommuters can combine the higher performance of ISDN with the simplicity of a terminal adapter. The DIVA T/A supports all standard modem AT commands. You can connect the DIV AT/A to a serial port on your computer that complements your TCP/IP application, without the nee
Summary of the content on the page No. 6
Installation Requirements To install the DIVA T/A, you will require the following: Item Description DIVA T/A Package • DIVA T/A ISDN Modem DIVA T/A software (CD) ISDN cable (RJ-45) Serial cable (RS-232) A/C Adapter Phone Adapter (RJ11) (where required) Terminating Resistor (if required - see page 129) DIVA T/A QuickStart Guide DIVA T/A Release Notes Desktop or Notebook DIVA T/A can be attached to any desktop or notebook computer. Remote Access Supplied as part of operating platf
Summary of the content on the page No. 7
Connecting the Cables to the DIVA T/A Follow the steps below to connect the cables to your DIV AT/A. 1 Turn off your computer before you connect the cables. 2 Connect the RJ45 end of the ISDN cable to the jack labeled ‘ISDN’ on the rear of the DIVA T/A. See below to complete the connection. Integrated NT1 (U): Connect the other end of the ISDN cable to your ISDN wall jack. S/T Interface: Connect the other end of the ISDN cable to an NT1 interface, whether part of the ISDN service (e.g. co
Summary of the content on the page No. 8
Connecting the Cables to the DIVA T/A After Connecting the Cables After connecting the power and the ISDN cable to the DIVA T/A, wait at least 10 seconds for the DIVA T/A to initialize and then check the ‘D’ and ‘Link’ LEDs. If they are both glowing continuously, then your DIVA T/A is operational from a previous configuration. If not, you will have to provide information on your ISDN setup using the DIVA Terminal Adapters software, which you will install next. See below. What’s Next? The ins
Summary of the content on the page No. 9
Windows 95/98/NT Installation and Setup To properly set up the DIVA T/A with a Windows 95/98/NT system, you must connect the cables, configure the operating system, and install the DIVA Terminal Adapters Software. Once the Terminal Adapters software is installed, you will use the Configuration Wizard to set your ISDN parameters. Step 1: Connect the Cables to your DIVAT/A Following the steps outlined on page 7. Step 2: Configure your Operating System The configuration procedure you must follow
Summary of the content on the page No. 10
Windows 95/98/NT Installation and Setup Windows 95 (Original Release and SP1) This install procedure is for the original release and Service Pack 1 (SP1) version of Windows 95. If you are using Windows 95 Service Release 2 (OSR2), go to “Windows 95 (OSR2)” on page 12. To verify the version installed on your machine, click ‘Start’, ‘Settings’, ‘Control Panel’, ‘System’, then click the ‘General’ tab. If you have the original or SP1 version of Windows 95 installed, you will see ‘4.00.950’ or ‘
Summary of the content on the page No. 11
Windows 95/98/NT Installation and Setup 5 In the ‘Install From Disk’ window, enter the drive letter of your CD drive (or use the Browse button to locate your CD drive) and click ‘OK’. 6 In the ‘Select Device’ window, select ‘Eicon DIVA T/A ISDN Modem’ and click ‘OK’. Go to “Installing the DIVA Software” on page 20. 7 DIVA T/A ISDN Modem User’s Guide Page 11
Summary of the content on the page No. 12
Windows 95/98/NT Installation and Setup Windows 95 (OSR2) This install procedure is for Windows 95 Service Release 2 (OSR2). If you are using original release or Service Pack 1 (SP1) version of Windows 95, go to “Windows 95 (Original Release and SP1)” on page 10. To verify the version installed on your machine, click ‘Start’, ‘Settings’, ‘Control Panel’, ‘System’, then click the ‘General’ tab. If you have Windows 95 OSR2 installed, you should see ‘4.00.950 B’, as shown. DUN 1.2 or Later Req
Summary of the content on the page No. 13
Windows 95/98/NT Installation and Setup 6 Enter the drive letter of your CD drive (or use the Browse button to locate your CD drive) and click ‘OK’. 7 In the ‘Update Device Driver Wizard’ window, click ‘Finish’. 8 Go to “Installing the DIVA Software” on page 20. DIVA T/A ISDN Modem User’s Guide Page 13
Summary of the content on the page No. 14
Windows 95/98/NT Installation and Setup Windows 98 Warning! It is very important to follow the steps, exactly as described below, to install the DIVA T/A software. The setup file for ISDN modems (mdmisdn.inf), supplied on the Microsoft Windows 98 CD, contains incorrect information about the DIV AT/A ISDN Modem (incorrectly referred to as ‘Eicon T-A External’). Using this setup file will cause the DIV AT/A to operate incorrectly. DO NOT use the ‘Add New Hardware’ applet (found in ‘Control Pan
Summary of the content on the page No. 15
Windows 95/98/NT Installation and Setup 6 Select ‘CD-ROM drive’ and click ‘Next’. 7 Click ‘Next’. 8 Click ‘Finish’ and go to “Installing the DIVA Software” on page 20. DIVA T/A ISDN Modem User’s Guide Page 15
Summary of the content on the page No. 16
Windows 95/98/NT Installation and Setup Windows NT 4.0 RAS Recommended Before you begin installing the DIVA T/A, we suggest that the Remote Access Service (RAS), also known as Dial-Up Networking, be installed with at least one modem. Any modem will do; it is only needed to install the DIVA T/A and can later be removed. Setup Instructions Follow these steps to set up the DIVA T/A under Windows NT 4.0. 1 Power on your PC with all cables connected (see page 7 for instructions). 2 Insert the DIV A
Summary of the content on the page No. 17
Windows 95/98/NT Installation and Setup 4 The ‘Install New Modem’ window appears. Select ‘Don't detect my modem; I will select it from a list’ then click ‘Next’. Important: Make sure that you select the choice above and do not let Windows NT choose its own modem driver. If you let Windows NT select the modem driver, you will not be able to communicate with the DIVA T/A. You will then have to delete the Win- dows NT installed modem and begin the install process again from Step 3. From the ‘In
Summary of the content on the page No. 18
Windows 95/98/NT Installation and Setup 6 Select ‘Eicon DIVA T-A ISDN Modem’, then click ‘Next’. 7 Select the appropriate COM Port the DI VAT/A is connected to. Click ‘Next’, then click ‘Finish’. 8 Close the ‘Modem Properties’ window. 9 After closing the ‘Modem Properties’ window, you are prompted to configure Dial-Up Networking, as the install modem list has changed. Click ‘Yes’ to configure Dial-Up Networking. 10 From the ‘Remote Access Setup’ window, remove any unused devices that use the
Summary of the content on the page No. 19
Windows 95/98/NT Installation and Setup Windows NT 3.51 Note on RAS If you are going to use the DIVA T/A with RAS, RAS must already be installed with at least one modem. Any modem will do; it is only needed to install the DIVA T/A and will later be removed. If you do not want to use RAS, go to “Installing the DIVA Software” on page 20. Setup Instructions 1 Power on your PC with all cables connected (see page 7 for instructions). 2 Insert the DIV AT/A CD into your computer's CD drive. 3 Open an
Summary of the content on the page No. 20
Windows 95/98/NT Installation and Setup Installing the DIVA Software The Setup Wizard installs all necessary files on your system. These include the DIVA T/A on-line documentation, the DIVA Terminal Adapters Program, and the Uninstall utility. Before you proceed, make sure you have completed the pre-installation procedure relevant to your software platform. To find the procedure relevant to your platform, see “Step 2: Configure your Operating System” on page 9. Installation Instructions 1 Ins
