Summary of the content on the page No. 1
Golden 150 Wireless Mini USB Adapter
Model # AWLL5077
User’s Manual
Rev. 1.0
Summary of the content on the page No. 2
Table of Contents 1. Introduction.....................................................................................................................................2 1.1 Package Contents......................................................................................................................2 1.2 Features.....................................................................................................................................2 2. Install Wireless USB Adapter....
Summary of the content on the page No. 3
1. Introduction Congratulations on your purchase of the Golden 150 Wireless Mini USB Adapter! Its high bandwidth combined with great wireless coverage delivers fast and reliable connection for all of your networking applications. The adapter will yield a higher throughput especially when it is used with AR570W Airlink101® Wireless 150 Router. A full range of security features WEP, WPA-PSK, and WPA2-PSK provide you the highest level of wireless network security. The bundled wireless uti
Summary of the content on the page No. 4
2. Install Wireless USB Adapter This section provides instructions on how to install the Golden 150 Wireless Mini USB Adapter. The driver is installed along with the utility. Step 2.1 Insert the USB adapter into an available USB port of your computer. Step 2.2 Click Cancel when you see the Found New Hardware Wizard. Windows XP/2000 Users: Windows Vista Users: 3
Summary of the content on the page No. 5
Step 2.3 Insert the Installation CD in the CD drive. The Autorun screen will pop up. Select Install Utility and Driver from the menu. 4
Summary of the content on the page No. 6
Note: If the Autorun screen doesn’t appear automatically go to Start, Run, and type D:\Utility\Setup.exe (where D is the letter of your CD drive) and click OK. Windows Vista Users: When you get warning message(s), make sure that you give permission to continue with the installation of the driver software. Step 2.4 The Airlink101 WLAN Monitor screen will popup. Click Next at the screen. Step 2.5 Click Install to begin the installation. 5
Summary of the content on the page No. 7
Step 2.6 For Windows XP, click on Continue Anyway. For Windows Vista: click on Install this driver software anyway. 6
Summary of the content on the page No. 8
Please wait when Windows is installing the driver for Airlink101 Wireless Adapter and the utility, Airlink101 Wireless Monitor. Step 2.7 Click Finish to complete the installation. 7
Summary of the content on the page No. 9
Step 2.8 Select Yes, I want to restart my computer now. Click Finish to complete the installation. The driver and utility have been installed. Please continue to the next section. 8
Summary of the content on the page No. 10
3. Connect to Wireless Network This section describes how to connect your wireless USB adapter to a wireless network. Step 3.1 Open the Airlink101 Wireless Monitor utility by double clicking on the Airlink101 Wireless Monitor Utility icon in the system tray at the bottom right-hand corner of your screen. Step 3.2 The Easy Setup Button (Wi-Fi Protected Setup) is a new and easy way to configure the encryption for your wireless network clients. In order to use it, you n
Summary of the content on the page No. 11
1. Push the Easy Setup Button of the Adapter until you see the following window pops up on the monitor. This window pops up to acknowledge you the Adapter is starting to establish a connection. 2. Within the following 2 minutes, push the Easy Setup Button (i.e. WPS Button) on the back of the Router and release it right away. The picture below shows Airlink101 AR570W Wireless 150 Router. 10
Summary of the content on the page No. 12
3. The router will now start the handshake with the wireless USB adapter. The connection will be established in few seconds. Continue to Step 3.5. If the connection is not able to establish, continue to Step 3.3. Step 3.3 Click the Available Network tab of the Wireless Monitor, select the wireless network that you wish to connect to, and click Add to Profile. If the network that you are attempting to connect does not have encryption enabled, you will receive a warning about connect
Summary of the content on the page No. 13
Step 3.5 The connection should be now established. Go to General tab to check the status of the connection. Verify that IP Address, Subnet Mask and Gateway have valid numbers assigned to them (instead of all 0’s). The Status should be Associated, and there will be green bars next to Signal Strength and Link Quality. 12
Summary of the content on the page No. 14
13
Summary of the content on the page No. 15
4. Wireless Monitor This section describes the various functions of the Wireless Monitor that you can configure, including the settings of wireless encryption. 4.1 General The General tab provides you with the status of the current connection, including signal, network name (SSID) and IP Address. At the bottom, you have options for controlling the utility and adapter: Show Tray Icon: Check this box to show or hide the utility icon on the task bar. 14
Summary of the content on the page No. 16
Radio Off: Check/uncheck this box to turn off/on the wireless function of the adapter. Disable Adapter: Check/uncheck this box to disable/enable the wireless adapter. For Windows XP users, you will see a checkbox “Windows Zero Config” which can be used to enable or disable the Windows XP’s built-in wireless utility, Windows Zero Configuration. It is suggested NOT to check this box and use Airlink101 Wireless Monitor that provides more advanced features to manage your wireless connecti
Summary of the content on the page No. 17
4.2 Profile Settings The Profile tab lists the current profiles and allows you to add/remove/edit profiles. The Available Profile(s) box lists all the profiles that you’ve created for your network. A profile is automatically created and added to this list when you connect to a new network. You can also manually add a profile. To modify an existing profile, select the profile from the Available Profile(s) box and click on Edit. The Profile box will appear allowing you to modif
Summary of the content on the page No. 18
The Profile box will appear allowing you to specify To create a new profile, click on Add. the settings for your new profile. Enter the profile settings here, including Profile Name, SSID, Network Authentication, Data Encryption and Network Key. Click OK to save the changes. The section 4.7, Configuring Encryption will give you the information of how to set the different options of the wireless network encryption settings. 17
Summary of the content on the page No. 19
4.3 Available Network The Available network tab lists all of the networks that the adapter detects in your area. Clicking Refresh will refresh the list. To connect to a network, select a network from the list and click Add to Profile. 18
Summary of the content on the page No. 20
4.4 Status The status section provides you with a list of information about the current status of the adapter. 19
