Summary of the content on the page No. 1
PMC-CX/E 04.4.26 10:16 AM ページ 1
OWNER'S MANUAL
Vestax Corporation
1-18-6 Wakabayashi, Setagaya-ku, Tokyo 154-0023 Japan
Phone 03-3412-7011 Fax 03-3412-7013
Web : www.vestax.com
Vestax (Europe) Ltd.
Unit 5 Riverwey Industrial Park Alton Hampshire GU34 2QL England, U.K.
Phone (0)1420-83000 Fax (0)1420-80040
Web : www.vestax.co.uk
Vestax Europe Technical Support
Rheinstr.213 D-53332 Bornheim Germany
Phone 49(0)2222-95-23-72 Fax 49(0)2222-95-23-74
q
Vestax Corporation
Summary of the content on the page No. 2
PMC-CX/E 04.4.26 10:16 AM ページ 3 CONGRATULATIONS Thank you for purchasing the Vestax PMC-CX Professional Mixing Controller. We suggest that you read through this owner's manual thoroughly so that you may enjoy the full use of this product safety and in the knowledge of all its special features and suitably applications. CAUTION 2 IMPORTANT SAFEGUARDS 3 FEATURES 4 FUNCTIO N 5 PROGRAM SECTION 6 MASTER SECTION 7 MIC/LINE SECTION 8 MONITOR SECTION 8 REAR PANEL 9 HOW TO CHANGE THE FADER UNIT 10 B
Summary of the content on the page No. 3
PMC-CX/E 04.4.26 10:16 AM ページ 5 SIZE 15. Damage Requiring Service-Unplug this product 16. Replacement Parts-When replacement parts are from the wall outlet and refer servicing to required, be sure the service technician has used qualified service personnel under the following replacement parts specified by the manufacturer conditions: or have the same characterristics as the original parts. Unauthorized substitutions may result in a. When the power-supply cord or plug is fire, electric shock o
Summary of the content on the page No. 4
PMC-CX/E 04.4.26 10:16 AM ページ 7 CROSS FADER PROGRAM SECTION iISOLATOR ON/OFF SWITCH Change to "CF-50" When set to "OFF", a full range signal is transmitted q Remove the fader knob and 4 screws which fix the crossfader panel, and the carefully remove the panel. (See fig-e) regardless of the position of any isolator controls. w Remove the 2 screws affixing the crossfader. (See fig-f) oHI PASS FILTER SWITCH e Carefully remove the multi-cable connector from the fader unit. (See fig-g) O
Summary of the content on the page No. 5
PMC-CX/E 04.4.26 10:16 AM ページ 9 HOW TO CHANGE THE FADER UNIT MIC / LINE SECTION REAR PANEL @9SUB MIC LEVEL VOLUME Adjusts the input level of the SUB MIC input. #0MAIN MIC / SUB LINE SELECTOR Selects between MAIN MIC and SUB LINE input. #1MIC / LINE EQ VOLUME Adjusts the HI and LOW frequencies for the signal chosen by MAIN MIC / SUB LINE SELECTOR. #2MIC / LINE LEVEL VOLUME Adjusts the input level of the MAIN MIC or SUB LINE input. #3MIC / LINE CUE SWITCH Sends the signal from
Summary of the content on the page No. 6
PMC-CX/E 04.4.26 10:16 AM ページ 11 HOW TO CHANGE THE FADER UNIT INPUT FADER MASTER SECTION @0BOOTH MONITOR EQ VOLUME Change to "IF-500" Adjusts the HI/MID/LOW frequencies for the BOOTH q Remove the fader knob. (See fig-a) OUT. w Remove the 4 screws which fix the input fader panel to the mixer. (See fig-b) @1BOOTH MONITOR LEVEL VOLUME e Remove the 2 screws which fix the input fader. (See fig-c) Adjusts the output level of BOOTH MONITOR. r Remove the input fader, and carefully remove the multi
Summary of the content on the page No. 7
PMC-CX/E 04.4.26 10:16 AM ページ 13 BLOCKDIAGRAM High Pass, Low Pass & Notch Filter (effect) on each PGM Suitable for all DJs On the PMC-CX each PGM has a filter effect section With more than enough creative room for even the with a high pass, low pass and (when pressed most experimental DJs the PMC-CX is truly suitable for together) a notch filter. These filters are used to alter the almost any type of DJ. In addition to the features frequency response of a given audio signal in either an ab
Summary of the content on the page No. 8
PMC-CX/E 04.4.26 10:16 AM ページ 15 SPECIFICATION READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1. Read instructions-All the safety and operating 10. Power sources-This product should be operated instructions should be read before the appliance only from the type of power sou
