Summary of the content on the page No. 1
OWNER'S MANUAL
Vestax Corporation
1-18-6 Wakabayashi, Setagaya-ku, Tokyo 154-0023 Japan
Phone 03-3412-7011 Fax 03-3412-7013
Web : www.vestax.com
Vestax (Europe) Ltd.
Unit 5 Riverwey Industrial Park Alton Hampshire GU34 2QL England, U.K.
Phone (0)1420-83000 Fax (0)1420-80040
Web : www.vestax.co.uk
Vestax Europe Technical Support
Rheinstr.213 D-53332 Bornheim Germany
Phone 49(0)2222-95-23-72 Fax 49(0)2222-95-23-74
Summary of the content on the page No. 2
CONGRATULATIONS Thank you for purchasing the Vestax PMC-007 Professional Mixing Controller. We suggest that you read through this owner's manual thoroughly so that you may enjoy the full use of this product safely and in the knowledge of all its special features and suitable applications. CONTENTS CAUTION 2 IMPORTANT SAFEGUARDS 3 FEATURES 4 FUNCTIO N 5 TOP PANEL 5 FRONT PANEL 7 REAR PANEL 8 HOW TO CHANGE THE FADER UNIT 9 CONNECTION 11 SPECIFICATIONS 12
Summary of the content on the page No. 3
READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1. Read instructions-All the safety and operating 10. Power sources-This product should be operated instructions should be read before the appliance only from the type of power source indicated on is operated. the marking label. If you are not sure of the type of power sup
Summary of the content on the page No. 4
15. Damage Requiring Service-Unplug this product 16. Replacement Parts-When replacement parts are from the wall outlet and refer servicing to required, be sure the service technician has used qualified service personnel under the following replacement parts specified by the manufacturer conditions: or have the same characterristics as the original parts. Unauthorized substitutions may result in a. When the power-supply cord or plug is fire, electric shock or other hazards. damaged. b. If liquid
Summary of the content on the page No. 5
FUNCTIONS TOP PANEL
Summary of the content on the page No. 6
!4BOOTH LEVEL qMIC LEVEL This knob is used to adjust the level of output through the This switch is used to adjust the signal level of the Main Booth section. MIC input. !5MONITOR SELECT SWITCH wMIC EQ This switch is used to select which type of monitor signal, The2-Band MIC EQ feature is used to adjust the equalization either CUE or MASTER, is heard in headphones connected level of the High & Low frequencies on the MIC input to this mixer. When set to CUE, both signals (including the signal. T
Summary of the content on the page No. 7
from position 1 to 2 will have only an effect in the headphones, @5LED LEVEL METER facilitating practice of a mix point or scratch point. As above. @2REHEARSAL MUTE/FREEZE INDICATOR LED @6CF REVERSE INDICATOR. When the Rehearsal Mute/Freeze feature is active this This LED is illuminated when the CF has been reversed as LED will illuminate. described in !.1 @3INPUT FADER @7CROSS FADER (CF) An input fader is used to adjust the input level on a given Assuming that the CF reverse is off, Rehearsal M
Summary of the content on the page No. 8
REAR PANEL SERIAL NO. INPUT CAUTION POWER #3LINE INPUT JACKS #7GROUND TERMINAL These jacks are used to connect line level output devices This connection point is used to ground turntables to the PMC-007. Devices with a line level of -10dB to connect to this unit. 0dB, such as CD players, MD players, tape decks, DAT #8EFFECT SEND JACK players etc may be connected to these jacks. The signal Used to connect the inputs of an external effects device. from these devices will then be f
Summary of the content on the page No. 9
HOW TO CHANGE THE FADER UNIT Exchanging a ReX Fader Unit The ReX (Rapid Exchange) fader system has been mounting unit, once release pull the fader upwards carefully. designed to allow users to quickly exchange faders. By t Remove the cable connector from the fader unit carefully. following and adhering to the following directions and yExchange the fader unit making sure to reconnect the advice you will be able to safely and easily exchange ReX cable connector unit correctly. type faders. In the
Summary of the content on the page No. 10
Changing the Direction of the Input Switch q Remove all knobs from the Battle Panel as illustrated. yExchange the input switch unit making sure to reconnect the cable connector unit correctly. w Release the top panel as illustrated. e Caution should be exercised when opening the top uReplace the screws as removed in point 4. Check to panel so as to avoid any unnecessary damage to the make sure that you have correctly and securely panel unit or release system. replaced the input switch unit. r B
Summary of the content on the page No. 11
CONNECTION SERIAL NO. INPUT CAUTION POWER MIC/AUX DJ/PHONO CD(R/RW) MD TAPE 5 BAND MASTER EQ MIC LINE 1 PHONO LINE 2 LINE 3 LINE 4 LINE 5 LINE 6 LINE 7 LINE 8 LOW MID LOW MID MID HI HI EQ POWER +12dB ON GAIN GAIN GAIN GAIN GAIN 0 MAIN VOLUME -12dB OFF LR BALANCE MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX SIGNAL/PEAK SIGNAL/PEAK SIGNAL/PEAK SIGNAL/PEAK SIGNAL/PEAK LEVEL LEVEL LEVEL LEVEL LEVEL MIC LINE 1 MIC/AUX MASTER MONITOR DJ/PHONO REC OUT CD(R/RW) CD- R/RW 1 MD TAP
Summary of the content on the page No. 12
SPECIFICATION q Vestax Corporation
