Summary of the content on the page No. 1
TD-20K_e.book 1 ページ ２００６年１２月７日 木曜日 午前９時２４分
Owner’s Manual
Thank you, and congratulations on your choice of the TD-20K Roland Drum System.
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” (p. 2) and “IMPORTANT NOTES” (p. 3).
These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured
that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be
Summary of the content on the page No. 2
TD-20K_e.book 2 ページ ２００６年１２月７日 木曜日 午前９時２４分 USING THE UNIT SAFELY The symbol alerts the user to important instructions Used for instructions intended to alert or warnings.The specific meaning of the symbol is the user to the risk of death or severe determined by the design contained within the injury should the unit be used triangle. In the case of the symbol at left, it is used for improperly. general cautions, warnings, or alerts to danger
Summary of the content on the page No. 3
TD-20K_e.book 3 ページ ２００６年１２月７日 木曜日 午前９時２４分 Important Notes 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Placement Additional Precautions 354a ADD • Do not expose the unit to direct sunlight, place it near • Brushes (nylon) can be used for brush playing. Do NOT devices that radiate heat, leave it inside an enclosed use metal brushes! 553 vehicle, or otherwise subject it to temperature extremes.
Summary of the content on the page No. 4
TD-20K_e.book 4 ページ ２００６年１２月７日 木曜日 午前９時２４分 MDS-20 (Drum Stand) TD-20 (Percussion Sound Module) Assemble the Drum Stand. Attach the stand holder (included with the drum stand MDS- 20) to the TD-20. Using the screws attached to the bottom panel, attach the About the Stand, refer to the MDS-20 Owner’s Manual. holder so the unit is oriented as shown in the diagram. fig.02.e Caution in Setting Up the Stand • Do NOT open the legs of the stand more than 135 degrees. The distance
Summary of the content on the page No. 5
TD-20K_e.book 5 ページ ２００６年１２月７日 木曜日 午前９時２４分 KD-120 (V-Kick Trigger Pad) Contents of the Package ❑ KD-120 Pad ❑ Leg x 2 ❑ Stand ❑ Beater * This package does not include a kick pedal. Use with a commercially available kick pedal installed on the KD-120. * If a felt beater is used, the felt will wear out. Use a plastic beater. Component (Parts) Names fig.07.e Lock nut Bracket Lug Output jack Sensor Shell Hoop Cushion Head T-bolt Tuning bolt Plate Leg Rubber foot * Due to the nature of the m
Summary of the content on the page No. 6
TD-20K_e.book 6 ページ ２００６年１２月７日 木曜日 午前９時２４分 KD-120 (V-Kick Trigger Pad) Setup Assembling the KD-120 1. Place the KD-120 pad, with the head surface facing downward, on a flat surface such as the floor. 2. Use the included tuning key to loosen and remove the bolts for the brackets on the back of the KD-120 pad. 3. Mount the stand on the brackets so that the output jack for the KD-120 pad faces up. Use the bolts you removed earlier to secure the KD-120 pad to the stand, tightening the b
Summary of the content on the page No. 7
TD-20K_e.book 7 ページ ２００６年１２月７日 木曜日 午前９時２４分 5. Loosen the T-bolts for the stand and mount the legs on the stand. KD-120 (V-Kick Trigger Pad) Install the legs as shown in the figure so that the ends of the legs protrude by about 2 cm. fig.11.e Extend the leg by about 2 cm. Mount the legs on the stand. T-bolt 6. Tighten the T-bolts to secure the legs to the stand. 7. Lift the KD-120 and place the stand and the four legs upright. 8. Adjust the angle of the head surface so that i
Summary of the content on the page No. 8
TD-20K_e.book 8 ページ ２００６年１２月７日 木曜日 午前９時２４分 KD-120 (V-Kick Trigger Pad) When Using a Twin (Double Kick) Pedal With the KD-120, you can also play using a twin (double kick) pedal. Set this up so that the striking points of the two beaters fall at equal distances to the left and right of the center of the head. fig.13 * When using a twin (double kick) pedal, as with a regular pedal, use the included beater or a plastic beater as the beater for the kick pedal. 8
Summary of the content on the page No. 9
TD-20K_e.book 9 ページ ２００６年１２月７日 木曜日 午前９時２４分 KD-120 (V-Kick Trigger Pad) Head Adjustment The head tension of the KD-120 can be adjusted. Adjusting the Head Tension Use the included tuning key to adjust the tension. In general, a tension that produces a strike response approximately the same as an acoustic bass drum will be appropriate. * Head tension that is too loose may not only cause incorrect operation, but may even damage the sensor. fig.14.e ac Lock nut tighten f e
Summary of the content on the page No. 10
TD-20K_e.book 10 ページ ２００６年１２月７日 木曜日 午前９時２４分 KD-120 (V-Kick Trigger Pad) Head Replacement When the head should be replaced The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: • The head surface is torn • Slack portions remain in the head even when the head tension is properly adjusted. Replacement heads (optional): Mesh Head (MH-12) Replacing the Head When replacing the head, use the includ
Summary of the content on the page No. 11
TD-20K_e.book 11 ページ ２００６年１２月７日 木曜日 午前９時２４分 PD-125/PD-105 (V-Pad) Component (Parts) Names fig.15.e Hoop (rim) Head The only difference between the PD-125 and Tuning bolts Stand fixing the PD-105 is the diameter. screw * The figure shows the PD-125. Lugs Bracket Output jack Shell Frame * Do not apply excessive force to the sensor located below the center of the head of the unit. Doing so can interfere with accurate detection, and may damage it. * Due to the nature of the materi
Summary of the content on the page No. 12
TD-20K_e.book 12 ページ ２００６年１２月７日 木曜日 午前９時２４分 PD-125/PD-105 (V-Pad) Adjusting the Head Adjusting the Head Tension When adjusting, use the included tuning key. On the PD-125/105, adjusting the head tension affects only the head response, and not the pitch of the sound, as it would on an acoustic drum. To adjust the pitch, edit the sound parameters of the TD-20. For details refer to the owner’s manual. Heads MUST BE TUNED BEFORE PLAYING. Like with an acoustic drum, accurate and equ
Summary of the content on the page No. 13
TD-20K_e.book 13 ページ ２００６年１２月７日 木曜日 午前９時２４分 CY-15R/CY-14C (V-Cymbal Ride/Crash) Contents of the Package CY-15R (Ride) CY-14C (Crash) ❑ CY-15R unit ❑ CY-14C unit ❑ Wing nut ❑ Wing nut ❑ Felt washer ❑ Felt washer ❑ Stopper ❑ Stopper ❑ Cable tie ❑ Cable tie Component (Parts) Names CY-15R (Ride) fig.19.e Wing Nut Felt Washer Stopper Bell Portion BOW/BELL OUTPUT Jack Bow Portion BOW/EDGE OUTPUT Jack Edge Portion Diameter: 15 inches CY-14C (Crash) fig.20.e Wing Nut Felt
Summary of the content on the page No. 14
TD-20K_e.book 14 ページ ２００６年１２月７日 木曜日 午前９時２４分 CY-15R/CY-14C (V-Cymbal Ride/Crash) Mounting on the Stand 1. Use the included tuning key to tighten the stopper bolt. The stopper keeps the V-Cymbal from turning, and prevents the cables from catching or getting tangled on the stand. fig.21.e Stopper Tighten the bolt with a (Be sure to orient commercially available it correctly) drum key 2. Position the Roland logo on the farther side, as viewed from the performer. 3. Tighten the felt
Summary of the content on the page No. 15
TD-20K_e.book 15 ページ ２００６年１２月７日 木曜日 午前９時２４分 Assemble the TD-20K Using the built-in connection cables of the MDS-20, connect the pads, cymbals, hi-hat, kick trigger pad, and percussion sound module. To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. fig.25.e * When connecting the cables, please refer to the marking labels that are attached to both ends of the cables. TD-
Summary of the content on the page No. 16
TD-20K_e.book 16 ページ ２００６年１２月７日 木曜日 午前９時２４分 Playing Methods PD-125/PD-105 fig.26.e Head Shots Hit only the head of the pad. With certain snare sounds, playing position will change the nuance of the sound. Head fig.27.e Rim Shots Strike the head and the rim of the pad simultaneously. Head Rim fig.28.e Cross Stick Only strike the rim of the pad. Depending on the instrument assigned to the rim you can play rim shots and/or cross Rim stick sounds. Rim To play the cross stick,
Summary of the content on the page No. 17
TD-20K_e.book 17 ページ ２００６年１２月７日 木曜日 午前９時２４分 Playing Methods CY-15R/CY-14C fig.30 Bow Shot This is the most common playing method, playing the middle area of the cymbal. fig.31.e Edge Shot This playing method involves striking the edge with the shoulder of the stick. The sound is played when the edge sensor area is struck, as shown in the Edge sensor figure. fig.32 Bell Shot (CY-15R Only) This playing method involves striking the bell. With the CY-15R, a sound is played
Summary of the content on the page No. 18
TD-20K_e.book 18 ページ ２００６年１２月７日 木曜日 午前９時２４分 Specifications KD-120 (V-Kick Trigger Pad) CY-15R (V-Cymbal Ride) Pad Size: 12 inches Size: 15 inches Dimensions: 490 (W) x 400 (D) x 500 (H) mm Triggers: 3 (Bow/Bell/Edge) 19-5/16 (W) x 15-3/4 (D) x 19-11/16 (H) inches Connectors: BOW/BELL Output Jack, BOW/EDGE Output Jack Weight: 7.7 kg Dimensions: 376 (W) x 376 (D) x 50 (H) mm 17 lbs 14-13/16 (W) x 14-13/16 (D) x 2 (H) inches Accessory: Beater Weight: 1.6 kg Option: Mesh Head (MH-12) 3 l
Summary of the content on the page No. 19
TD-20K_e.book 19 ページ ２００６年１２月７日 木曜日 午前９時２４分 Specifications For EU Countries This product complies with the requirements of European Directive 89/336/EEC. 19
Summary of the content on the page No. 20
TD-20K_e.book 20 ページ ２００６年１２月７日 木曜日 午前９時２４分 Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. PHILIPPINES CURACAO URUGUAY NORWAY JORDAN AFRICA G.A. Yupangco & Co. Inc. Zeelandia Music Center Inc. Todo Musica S.A. Roland Scandinavia Avd. MUSIC HOUSE CO. LTD. 339 Gil J. Puyat Avenue Orionweg 30 Francisco Acuna de Figueroa Kontor Norge FREDDY FOR MUSIC EGYPT Makati, Metro Manila 1200, Curacao, N
