Metra Electronics HONDA RIDGELINE 99-7870T user manual

Summary of the content on the page No. 1

INSTALLATION INSTRUCTIONS FOR PART 99-7870
APPLICATIONS
Honda Ridgeline
2005-2010
99-7870G/99-7870T
KIT FEATURES
• DIN Head Unit Provision With A Pocket
• ISO DIN Head Unit Provision With A Pocket
• Painted To Match Factory Dash:
G = GRAY, T= TAN
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
• 70-1729 - Honda harness 2009-up or 70-1721 1998-2008
• 40-HD10 - Honda Antenna Adapter 2005-up
KIT COMPONENTS
• A) Radio Housing • B) Radio Housing Brackets (to hold factory pocket below radio)

Summary of the content on the page No. 2

99-7870 TABLE OF CONTENTS Dash Disassembly Honda Ridgeline 2005-2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2, 3, 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Summary of the content on the page No. 3

DASH DISASSEMBLY 99-7870 HONDA RIDGELINE 2005-2010 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove entire panel sur- rounding radio and a/c control all the way over to left side of steering wheel. (Figure A) 3 Remove (5) Phillips screws securing B the radio and pocket assembly. (Figure B) Remove (2) Phillips screws (1 per 4 side) securing factory pocket to radio/pocket bracket assembly. (Figure C, D) D C 1

Summary of the content on the page No. 4

99-7870 KIT ASSEMBLY HONDA RIDGELINE 2005-2010 A 1 Attach the corresponding radio hous- ing bracket to the radio housing Housing with Pocket using the included carriage bolts and kep nuts. (Figure A) 2 Position the factory pocket into the Carriage Bolts/Kep Nuts assembled radio housing assembly Radio Housing Brackets and secure with the factory hard- ware. (Figure B) Rear View B LOCATOR LOCATOR 1 SCREW ON BOTH SIDES 2

Summary of the content on the page No. 5

99-7870 KIT ASSEMBLY HONDA RIDGELINE 2005-2010 DIN HEAD UNIT PROVISION A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket head unit into the cage and secure. (Figure B) B 3

Summary of the content on the page No. 6

99-7870 KIT ASSEMBLY HONDA RIDGELINE 2005-2010 ISO DIN HEAD UNIT PROVISION A 1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 2 Slide the head unit into the radio opening until the side clips engage. (Figure B) Snap the trim plate into the Radio 3 B Housing. (Figure B) 4

Summary of the content on the page No. 7

99-7870 KIT ASSEMBLY FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recommends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring c

Summary of the content on the page No. 8

99-7870 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 04/21/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7870