Summary of the content on the page No. 1
RF COMMUNICATIONS PRODUCTS
20 19 18 17 16 15 14 13 12 11
IF
LIMITER
AMP
RSSI
MIXER
QUAD
OSCILLATOR
– +
+–
V
REG
AUDIO
EB
1 2 3 4 5 6 7 8 9 10
SA606
Low-voltage high performance mixer FM
IF system
Product Specification
1997 Nov 07
Replaces data of October 26, 1993
RF Data Handbook
Philips Semiconductors
Summary of the content on the page No. 2
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 DESCRIPTION PIN CONFIGURATION The SA606 is a low-voltage high performance monolithic FM IF D and DK Packages system incorporating a mixer/oscillator, two limiting intermediate frequency amplifiers, quadrature detector, logarithmic received RF IN+ 1 20 MIXER OUT signal strength indicator (RSSI), voltage regulator and audio and RSSI op amps. The SA606 is available in 20-lead SOL RF IN- DECOUPLING IF
Summary of the content on the page No. 3
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 BLOCK DIAGRAM 20 19 18 17 16 15 14 13 12 11 IF LIMITER AMP RSSI MIXER QUAD OSCILLATOR – + +– V REG AUDIO EB 1 2 3 4 5 6 7 8 9 10 SR00348 Figure 2. Block Diagram DC ELECTRICAL CHARACTERISTICS V = +3V, T = 25°C; unless otherwise stated. CC A LIMITS SYMBOL SYMBOL P PARAMETER ARAMETER TEST TEST CONDITIONS CONDITIONS UNITS UNITS MIN TYP MAX V Power supply voltage range 2.7 7.0 V CC I DC current drain
Summary of the content on the page No. 4
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 AC ELECTRICAL CHARACTERISTICS (Continued) LIMITS SYMBOL SYMBOL P PARAMETER ARAMETER TEST TEST CONDITIONS CONDITIONS UNITS UNITS MIN TYP MAX THD Total harmonic distortion -35 -50 dB S/N Signal-to-noise ratio No modulation for noise 62 dB RF RSSI output, R = 2kΩ RF level = -118dBm 0.3 .80 V 9 RF level = -68dBm .70 1.1 1.80 V RF level = -23dBm 1.20 1.8 2.50 V RSSI range 90 dB RSSI accuracy +1.5 dB IF
Summary of the content on the page No. 5
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 -25dB, -10dB, -29dB, -10.6dB, -36dB, 1500/50Ω PAD 50/50Ω PAD 929/50Ω PAD 50/50Ω PAD 156k/50Ω PAD C26 51.5 96.5 96.5 51.7 50.5 R18 3.3k 71.5 2430 71.5 32.8 1.3k 3880 32.6 C20 R17 C15 C24 C22 C19 C16 2.4k SW9 FLT1 SW8 SW7 SW6 SW5 FLT2 C18 C21 C17 C23 20 19 18 17 16 15 14 13 12 11 IF LIMITER AMP MIXER RSSI QUAD OSCILLATOR + + – – V REG AUDIO 1 2 3 4 5 6 7 8 9 10 R13 R11 R9 SW11 SW1 SW3 SW4 C1 R10 C9
Summary of the content on the page No. 6
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 C26 R18 3.3k R17 C15 2.4k FLT1 FLT2 C18 C21 C17 C23 20 19 18 17 16 15 14 13 12 11 IF LIMITER AMP MIXER RSSI QUAD OSCILLATOR +– – + V REG 1 2 3 4 5 6 7 8 9 10 R11 C1 10k C9 C12 C8 R10 10k L1 C2 C27 C7 2.2μF C10 C5 R19 IFT1 11k L2 45MHz X1 C6 INPUT C19 390pF C14 RSSI AUDIO V CC OUTPUT NE606D/DK Demo Board Application Component List C1 51pF NPO Ceramic C23 100nF +10% Monolithic Ceramic C2 220pF NPO Ce
Summary of the content on the page No. 7
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 RF GENERATOR NE606 DEMO BOARD 45MHz RSSI AUDIO V (+3) CC DE-EMPHASIS FILTER DC VOLTMETER C–MESSAGE HP339A DISTORTION SCOPE ANALYZER SR00351 Figure 5. SA606 Application Circuit Test Set Up NOTES: 1. C-message: The C-message and de-emphasis filter combination has a peak gain of 10 for accurate measurements. Without the gain, the measurements may be affected by the noise of the scope and HP339 anal
Summary of the content on the page No. 8
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 mA 6 V = 7V CC 5 V = 5V CC 4 V = 3V CC 3 V = 2.7V CC °C 2 –55 –35 –15 5 25 45 65 85 105 125 SR00352 Figure 6. I vs Temperature CC –8.0 –8.5 –9.0 2.7V 3V –9.5 –10.0 7V –10.5 –11.0 –11.5 –12.0 –12.5 –13.0 –13.5 –14.0 –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 Temperature (°C) SR00353 Figure 7. Third Order Intercept Point vs Supply Voltage 1997 Nov 07 8 50 INPUT INTERCEPT POINT (dBm) Ω
Summary of the content on the page No. 9
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 8.00 7.75 7.50 7.25 7.00 6.75 7.0V 6.50 3V 6.25 2.7V 6.00 5.75 5.50 5.25 5.00 –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 TEMPERATURE (°C) SR00354 Figure 8. Mixer Noise Figure vs Supply Voltage 18.00 17.75 2.7V 17.50 3V 17.25 7.0V 17.00 16.75 16.50 16.25 16.00 –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 TEMPERATURE (°C) SR00355 Figure 9. Conversion Gain vs Supply Voltage 1997 Nov 07 9 CONVERSION GAIN
Summary of the content on the page No. 10
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 20 10 0 RF = 45MHz IF = 455kHz –10 –20 –30 3rd ORDER PRODUCT FUND PRODUCT –40 –50 –60 –70 –80 *50Ω INPUT –66 –56 –46 –36 –26 –16 –6 4 14 24 34 RF* INPUT LEVEL (dBm) SR00356 Figure 10. Mixer Third Order Intercept and Compression 1997 Nov 07 10 IF OUTPUT POWER (–dBm)
Summary of the content on the page No. 11
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 5 AUDIO 0 –5 –10 V = 3V CC –15 RF = 45MHz DEVIATION = ±8kHz –20 AUDIO LEVEL = 104.9mV RMS –25 –30 AM REJECTION –35 –40 THD + NOISE –45 –50 –55 –60 NOISE –65 –125 –115 –105 –95 –85 –75 –65 –55 –45 –35 –25 RF LEVEL (dBm) SR00357 Figure 11. Sensitivity vs RF Level (-40°C) 5 AUDIO 0 –5 –10 V = 3V CC RF = 45MHz –20 DEVIATION = ±8kHz AUDIO LEVEL = 117.6mV RMS –25 –30 AM REJECTION –35 –40 –45 –50 THD + N
Summary of the content on the page No. 12
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 5 AUDIO 0 –5 –10 V = 3V –15 CC RF = 45MHz –20 DEVIATION = ±8kHz AUDIO LEVEL = 127mV RMS –25 –30 AM REJECTION –35 –40 –45 THD + NOISE –50 –55 –60 NOISE –65 –125 –115 –105 –95 –85 –75 –65 –55 –45 –35 –25 RF LEVEL (dBm) SR00359 Figure 13. Sensitivity vs RF Level (Temperature 85°C) 5 AUDIO 0 –5 –10 V = 3V CC –15 RF = 45MHz RF LEVEL = -45dBm –20 DEVIATION = ±8kHz AUDIO LEVEL = +117.6mV RMS –25 –30 –35
Summary of the content on the page No. 13
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 2.400 2.000 +85°C 1.600 ROOM 1.200 -40°C 0.800 0.400 0.000 –95 –85 –75 –65 –55 –45 –35 –25 –15 –5 5 IF LEVEL (dBm) SR00361 Figure 15. RSSI (455kHz IF @ 3V) 2.1 2.0 1.9 1.8 1.7 1.6 1.5 1.4 +85°C 1.3 +27°C 1.2 -40°C 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 –125 –115 –105 –95 –85 –75 –65 –55 –45 –35 –25 RF LEVEL (dBm) SR00362 Figure 16. RSSI vs RF Level and Temperature - V = 3V CC 1997 Nov 07 13 VOLTAGE
Summary of the content on the page No. 14
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 V 300 V = 7V CC 250 200 V = 5V CC 150 V = 3V CC 100 V = 2.7V CC 50 0 °C –55 –35 –15 5 25 45 65 85 105 125 SR00363 Figure 17. Audio Output vs Temperature 1997 Nov 07 14 mV RMS
Summary of the content on the page No. 15
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 *Applies to Stand-Alone data sheets only. KTDN9/91 NE606 SR00365 Figure 18. SA606D SOL Product Board Layout (2X Actual Size* — For Reference Use Only) 1997 Nov 07 15
Summary of the content on the page No. 16
Philips Semiconductors Product specification Low-voltage high performance mixer FM IF system SA606 606 Silk Screen 606 TOP 606 BOTTOM NOTE; All views are TOP VIEW and not actual size. For reference only. SR00366 Figure 19. 1997 Nov 07 16
Summary of the content on the page No. 17
Philips Semiconductors Product specification Low-voltage high-performance mixer FM IF system SA606 SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1 1997 Nov 07 17
Summary of the content on the page No. 18
Philips Semiconductors Product specification Low-voltage high-performance mixer FM IF system SA606 SSOP20: plastic shrink small outline package; 20 leads; body width 4.4 mm SOT266-1 1997 Nov 07 18
Summary of the content on the page No. 19
Philips Semiconductors Product specification Low-voltage high-performance mixer FM IF system SA606 DEFINITIONS Data Sheet Identification Product Status Definition This data sheet contains the design target or goal specifications for product development. Specifications Objective Specification Formative or in Design may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right
