Summary of the content on the page No. 1
3-865-708-11(2)
CD Radio
Cassette-Corder
Operating Instructions
CFD-ZW700
CFD-ZW705
CFD-ZW750
CFD-ZW770
1999 by Sony Corporation
Summary of the content on the page No. 2
Information Warning For customers in the United States To prevent fire or shock hazard, do This equipment has been tested and found to not expose the player to rain or comply with the limits for a Class B digital moisture. device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordan
Summary of the content on the page No. 3
Basic Operations Table of contents Basic Operations 4 Playing a CD 6 Listening to the radio 8 Playing a tape 10 Recording on a tape The CD Player Setting Up 12 Using the display 25 Hooking up the system 13 Locating a specific point in a 28 Selecting the audio emphasis track (Sound Mode/MEGA BASS/5 BAND GRAPHIC EQUALIZER) 14 Playing tracks repeatedly (Repeat Play) 15 Playing tracks in random order Additional Information (Shuffle Play) 30 Precautions 16 Creating your own program 32 Troubleshooting
Summary of the content on the page No. 4
Basic Operations Playing a CD 1,2 3 For hookup instructions, see pages 25 – 27. 1 Push 6 PUSH OPEN/CLOSE down to open the CD compartment and place the CD on the CD compartment. With the label side up 2 Close the lid of the CD compartment. 3 Press ^. Display The player turns on (direct power-on) and plays all the tracks once. Track number Playing time 4 Basic Operations
Summary of the content on the page No. 5
Basic Operations Use these buttons for additional operations POWER 6 PUSH OPEN/CLOSE p ^ VOLUME +, – =, + Tip To Press Next time you want to adjust the volume VOLUME +, – listen to a CD, just press ^. The player turns on (VOL +, – on the remote, automatically and starts CFD-ZW750/ZW770 only) playing the CD. stop playback p pause playback ^ ( P on the remote, CFD-ZW750/ZW770 only) Press the button again to resume play after pause. go to the next track + go back to the previous track = remove the
Summary of the content on the page No. 6
Listening to the radio 1 2 For hookup instructions, see pages 25 – 27. Display 1 Press RADIO BAND until the band you want appears in the display (direct power-on). Indicates an FM stereo 2 Hold down TUNE•TIME SET + broadcast or – (TUNE + or – on the remote, CFD-ZW750/ZW770 only) until the frequency digits begin to change in the display. The player automatically scans the radio frequencies and stops when it finds a clear station. If you cannot tune in to a station, press the button repeatedly to
Summary of the content on the page No. 7
Basic Operations Use these buttons for additional operations VOLUME +, – POWER MODE Tips To Press • If the FM broadcast is adjust the volume VOLUME +, – noisy, press MODE until “Mono” appears in the (VOL +, – on the remote, display and radio will CFD-ZW750/ZW770 only) play in monaural. turn on/off the radio POWER • Next time you want to listen to the radio, just press RADIO BAND. To improve broadcast reception The player turns on automatically and starts Reorient the antenna for FM. Reorient the
Summary of the content on the page No. 8
Playing a tape 2 12 1 For hookup instructions, see pages 25 – 27. 1 Press p6 to open the tape compartment and insert a recorded tape. Use TYPE I (normal) tape only. Close the compartment. With the side you want to play facing you Display 2 Press (. The player turns on ( direct power-on) and starts playing. 8 Basic Operations
Summary of the content on the page No. 9
Basic Operations Use these buttons for additional operations VOLUME +, – POWER 0, ) p6 P 0, ) p6 P Note To Press During playback, do not adjust the volume VOLUME +, – press buttons on the other deck. Otherwise (VOL +, – on the remote, the playback speed may CFD-ZW750/ZW770 only) change. stop playback p6 Tip fast-forward or rewind the tape ) or 0 Next time you want to pause playback P listen to a tape, just Press the button again to press (. The player resume play after pause. turns on automatica
Summary of the content on the page No. 10
Recording on a tape 2 31 For hookup instructions, see pages 25 – 27. 1 Press p6 to open the tape compartment on deck B and insert a blank tape. Use TYPE I (normal) tape only. With the side you want to record on facing you 2 Select the program source you want to record. Display To record from the CD player: insert a CD (see page 4) and press CD. To record from the radio: tune in the station you want (see page 6). To record from the tape (dubbing): insert a recorded tape into deck A and press TAP
Summary of the content on the page No. 11
Basic Operations Deck B 3 Start recording. To record from the CD player and the radio, press r on deck B (( is depressed automatically). Deck A To record from the tape, press r on deck B ((is depressed automatically). Then press ( on deck A. (For high speed dubbing, press HIGH-SPEED DUBBING instead of ( on deck A). Tips Use these buttons for additional operations • Adjusting the volume or the audio emphasis (see POWER pages 28 and 29) will not affect the recording level. • If the AM program make
Summary of the content on the page No. 12
The CD Player Using the display DISPLAY ENT MEM You can check information about the CD using the display. Checking the total track numbers and playing time Press DISPLAY ENT MEM in stop mode. If the CD has more than 12 tracks, “OVER 12” appears in the display. Total playing time Total track number Music calendar Checking the remaining time Press DISPLAY ENT MEM while playing a CD. The track numbers in the music calendar disappear after they are played. To display Press DISPLAY ENT MEM the curren
Summary of the content on the page No. 13
The CD Player Locating a specific point in a track = , + You can quickly find a specific point in a track while playing a CD. You can also locate any track using the number buttons on the remote (CFD- ZW750/ZW770 only). To locate Press a point while listening to + (forward) or = the sound (backward) while playing and hold down until you find the point a point while observing + (forward) or = the display (backward) in pause and hold down until you find the point Note a specific track directly nu
Summary of the content on the page No. 14
Playing tracks repeatedly MODE ^ p (Repeat Play) You can play tracks repeatedly in normal, shuffle or program play modes (see pages 15 and 16). =, + 1 Press p. “Cd” appears in the display. On the remote (CFD- 2 Proceed as follows. ZW750/ZW770 only) • Use ( instead of To repeat Do this ^. a single track 1 Press MODE until “REP 1” • When you have appears. selected “REP 1”, 2 Press = or + to select select the track by the track that you want to pressing the number buttons. repeat. 3 Press ^. all t
Summary of the content on the page No. 15
The CD Player Playing tracks in random order MODE ^ p (Shuffle Play) You can play tracks in random order. 1 Press p. “Cd” appears in the display. On the remote (CFD- 2 Press MODE until “SHUF” appears in the display. ZW750/ZW770 only) 3 Press ^ to start shuffle play. Use ( instead of ^. To cancel Shuffle Play Press MODE until “SHUF” disappears from the display. The CD Player 15
Summary of the content on the page No. 16
Creating your own program MODE ^ p (Program Play) You can make a program of up to 20 tracks in the order you want them to be played. DISPLAY ENT MEM On the remote (CFD- 1 Press p. ZW750/ZW770 only) “Cd” appears in the display. 1 Press p. 2 Press MODE until 2 Press MODE until “PGM” appears in the display. “PGM” appears in the display. 3 Press = or + then press DISPLAY ENT MEM 3 Press the number for the tracks you want to program in the order buttons for the tracks you want. you want to program in
Summary of the content on the page No. 17
The CD Player Tips To cancel Program Play • You can play the same Press MODE until “PGM” disappears from the program again, since the display. program is saved until you open the disc compartment. To check the order of tracks before play • You can record your own Press DISPLAY ENT MEM. program. After you’ve created the program, Every time you press the button, the track number insert a blank tape into appears in the programed order. deck B and press r on deck B to start recording. To change the
Summary of the content on the page No. 18
Enjoying sound effects (LOOP/FLASH) FLASH LOOP You can repeat part of a CD (LOOP) and can “flash” the CD sound (FLASH) during playback. 1 Play a CD. 2 Press and hold LOOP or FLASH at the point you want to start the function. To Press and hold repeat a selected part of a CD LOOP “flash” the CD sound FLASH To cancel the LOOP or FLASH function Release the button. The player returns to normal play. 18 The CD Player
Summary of the content on the page No. 19
The Radio The Radio Presetting radio stations RADIO BAND DISPLAY ENT MEM You can store radio stations into the player’s memory. You can preset up to 20 radio stations, 10 for each band in any order. TUNE TIME SET –, + PRESET –, + On the remote (CFD- 1 Press RADIO BAND until the band you want ZW750/ZW770 only) appears in the display. 1 Press BAND to select the band. 2 Set the frequency to the station you want. 2 Set the frequency to 3 Press and hold DISPLAY ENT MEM for 2 the station you want. s
Summary of the content on the page No. 20
Playing preset radio stations RADIO BAND PRESET –, + Once you have preset the stations, use PRESET +/– on the player or the number buttons on the remote (CFD- ZW750/ZW770 only) to tune in to your favorite stations. On the remote (CFD- 1 Press RADIO BAND to select the band. ZW750/ZW770 only) 2 Press PRESET + or – to tune in the stored station. 1 Press BAND to select the band. 2 Press the number buttons to tune in the stored station. 20 The Radio
