Summary of the content on the page No. 1
TD-8616
ADSL2+ Modem
Rev: 2.0.0
1910010591
Summary of the content on the page No. 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO.,
Summary of the content on the page No. 3
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarante
Summary of the content on the page No. 4
DECLARATION OF CONFORMITY For the following equipment: Product Description: ADSL2+ Modem Model No.: TD-8616 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 2004 / 108 / EC, Directives 2006 / 95 / EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents： EN 55022:2006+A1:200
Summary of the content on the page No. 5
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Introduction ........................................................................................ 2 1.1 Product Overview...................................................................................................... 2 1.2 Main Features ...........................................................................................................
Summary of the content on the page No. 6
TD-8616 ADSL2+ Modem User Guide Package Contents The following items should be found in your package: One TD-8616 ADSL2+ Modem One Power Adapter for TD-8616 ADSL2+ Modem Quick Installation Guide One RJ45 cable Two RJ11 cables One ADSL splitter One Resource CD , including: This User Guide Other Helpful Information Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor. 1
Summary of the content on the page No. 7
TD-8616 ADSL2+ Modem User Guide Chapter 1. Introduction Thank you for choosing the TD-8616 ADSL2+ Modem . 1.1 Product Overview The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet network. The Modem is easy to use. The TD-8616 connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors. Multiple workstations can be networked and connecte
Summary of the content on the page No. 8
TD-8616 ADSL2+ Modem User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs locate on the front panel, which indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Status Indication On The modem is powered on. Power The modem is off. Please ensure that the power adapter is connected Off correctly. On There is a device connected to this LAN port. Flash The modem is sending or receiving data over
Summary of the content on the page No. 9
TD-8616 ADSL2+ Modem User Guide 2.2 The Back Panel Figure 2-2 ON/OFF: The switch for the power. POWER: The Power plug is where you will connect the power adapter. RESET: There are two ways to rese t the Modem's factory defaults. Method one: With the Modem powered on, use a pin to press and hold the RESET button (about 5 seconds) until the SYS LED becomes quick-flash from slow-flash. And then release the button and wait the Modem to reboot to its factory default settings. Metho
Summary of the content on the page No. 10
TD-8616 ADSL2+ Modem User Guide the rear panel of TD-8616, and insert the other end into the wall socket. Method two：You can use a separate splitter. External splitter can divide the data and voice, and then you can access the Internet and make calls at the same time. The external splitter has three ports: • LINE: Connect to the wall jack • PHONE: Connect to the phone sets • MODEM: Connect to the ADSL LINE port of TD-8616 Plug one end of the twisted-pair ADSL cable into the ADSL LINE p
Summary of the content on the page No. 11
TD-8616 ADSL2+ Modem User Guide Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-8616 or connect your adapter to a Hub/Switch which has connected to the Modem, you need to configure your PC’s IP address. Follow the steps below to configure it. Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1). Figure 3-1 Step 2: Right click Local Area Connection (LAN), and
Summary of the content on the page No. 12
TD-8616 ADSL2+ Modem User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. 7
Summary of the content on the page No. 13
TD-8616 ADSL2+ Modem User Guide Figure 3-3 Step 4: Configure the IP address (Figure 3-4): Enter the IP address as 192.168.1.* (* is any value between 2 to 254, Subnet mask is 255.255.255.0). After that, click OK. 8
Summary of the content on the page No. 14
TD-8616 ADSL2+ Modem User Guide Figure 3-4 Note: 1) The users of Windows 98 can open TCP/IP Properties according to the following: Right-press (Mouse) Network Neighbor -> Choose Properties -> Double-press TCP/IP. PCI Fast Ethernet Adapter. 2) The words in fact maybe are different with this guide. Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab, type cmd in the field and press Ente
Summary of the content on the page No. 15
TD-8616 ADSL2+ Modem User Guide Figure 3-5 If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Modem. Figure 3-6 You can check it follow the steps below: 1) Is the connection between your PC and the Modem correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the Modem's IP address is 192.168.1.1, your PC's IP address
Summary of the content on the page No. 16
TD-8616 ADSL2+ Modem User Guide Figure 3-7 After that you will see the page as follow when ADSL connection is OK. Figure 3-8 11
Summary of the content on the page No. 17
TD-8616 ADSL2+ Modem User Guide Chapter 4. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Management page. After your successful login, you can configure and manage the device. There are main menus on the top of the W
Summary of the content on the page No. 18
TD-8616 ADSL2+ Modem User Guide Figure 4-2 4.1.2 Traffic Statistics Choose “Statistics→Traffic Statistics” menu, and you will be able to view the traffic statistics about the Modem. Figure 4-3 13
Summary of the content on the page No. 19
TD-8616 ADSL2+ Modem User Guide 4.2 Basic Setup Choose “Basic Setup”, you can see the next submenus: WAN Setting, LAN Setting and ADSL. Figure 4-4 Click any of them, and you will be able to configure the corresponding function. 4.2.1 WAN Setting Choose “Basic Setup→WAN Setting” menu, you can configure the parameters for WAN ports in the next screen (shown in Figure 4-5). Figure 4-5 WAN Setting: WAN settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path Ide
Summary of the content on the page No. 20
TD-8616 ADSL2+ Modem User Guide Figure 4-6 • PVC Pool: PVC Pool contains multiple VPI/VCI sets. The Modem can match PVC automatically and it can be plug and play. The detailed VPI/VCI sets inside PVC Pool are shown in Figure 4-7, besides you can add VPI/VCI sets to or remove VPI/VCI sets from the PVC pool. Figure 4-7 • Status: If you want to use a designed VC, you should activate it. • VPI: Identifies the virtual path between endpoints in an ATM network. The valid range is from 0
