Silicon Laboratories SI2494/39 user manual

User manual for the device Silicon Laboratories SI2494/39

Device: Silicon Laboratories SI2494/39
Category: Modem
Manufacturer: Silicon Laboratories
Size: 4.35 MB
Added : 8/3/2013
Number of pages: 304
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Silicon Laboratories SI2494/39. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Silicon Laboratories SI2494/39.

For your convenience

If looking through the Silicon Laboratories SI2494/39 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Silicon Laboratories SI2494/39 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Silicon Laboratories SI2494/39 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Silicon Laboratories SI2494/39 User manual - Online PDF
Advertisement
« Page 1 of 304 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Silicon Laboratories SI2494/39 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Silicon Laboratories SI2494/39. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

AN93
Si2493/57/34/15/04 (Revision D) and Si2494/39
Modem Designer’s Guide
1. Introduction
The Si2494/93/57/39/34/15/04 ISOmodem chipset family consists of a 38-pin QFN (Si2494/39) or 24-pin TSSOP
(Si2493/57/34/15/04) or 16-pin SOIC (Si2493/57/34/15/04) low-voltage modem device, and a 16-pin SOIC line-
side DAA device (Si3018/10) connecting directly with the telephone local loop (Tip and Ring). This modem solution
is a complete hardware (controller-based) modem that connects to a host processor

Summary of the content on the page No. 2

AN93 2 Rev. 1.3

Summary of the content on the page No. 3

AN93 TABLE OF CONTENTS Section Page 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1. Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. Modem (System-Side) Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.1. Resetting the Device . . . . . . . . . . . . . . . . . .

Summary of the content on the page No. 4

AN93 2.6.6.2. AT Command Macro Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 2.6.6.3. Autoloading Firmware Upgrade Example . . . . . . . . . . . . . . . . . . . . . . . . 35 2.6.6.4. Combination Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 3. DAA (Line-Side) Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 3.1. Hookswitch and DC Termination . . . . . . . . .

Summary of the content on the page No. 5

AN93 5.7.11. U4F (Flash Hook Time Register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 5.7.12. U50–U51 (Loop Current Debouncing Registers) . . . . . . . . . . . . . . . . . . . . . 105 5.7.13. U52 (Transmit Level Register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 5.7.14. U53 (Modem Control Register 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 5.7.15. U54 (Calibration Timing Register) . . . . . . . . . . . . .

Summary of the content on the page No. 6

AN93 6.6. Intrusion/Parallel Phone Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 6.6.1. On-Hook Condition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 6.6.1.1. Line Not Present/In Use Indication (Method 1—Fixed) . . . . . . . . . . . . . 161 6.6.1.2. Line Not Present/In Use Indication (Method 2—Adaptive). . . . . . . . . . . 162 6.6.2. Off-Hook Condition. . . . . . . . . . . . . . . . . . . . . . . . . .

Summary of the content on the page No. 7

AN93 7.5.8. Speakerphone Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 7.6. Telephone Answering Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 7.6.1. Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 7.6.2. TAM Hands-Free—Idle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 7.6.2.1. Record OGM . .

Summary of the content on the page No. 8

AN93 9. Chinese ePOS SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 9.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 9.2. SMS AT Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 9.2.1. SMS User Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Summary of the content on the page No. 9

AN93 1.1. Selection Guide Tables 1 through 3 list the modulations, protocols, carriers, tones and interface modes supported by the Si2494/39 and Si2493/57/34/15/04 ISOmodem family. The Si2493 supports all modulations and protocols from Bell 103 through V.92. The Si2457 supports all modulations and protocols from Bell 103 through V.90. The Si2434 supports all modulations and protocols from Bell 103 through V.34. The Si2415 supports all modulations and protocols from Bell 103 through V.32bis. The

Summary of the content on the page No. 10

AN93 Table 3. Carriers and Tones Specification Transmit Carrier Receive Carrier Answer Carrier Detect (Acquire/ (Hz) (Hz) Tone (Hz) Release) V.92 Variable Variable per ITU-T V.92 V.90 Variable Variable per ITU-T V.90 V.34 Variable Variable per ITU-T V.34 V.32bis 1800 1800 2100 per ITU-T V.32bis V.32 1800 1800 2100 per ITU-T V.32 V.29 1700 1700 per ITU-T V.29 V.22bis, V.22 1200 2400 2100 –43 dBm/–48 dBm Originate/answer 2400 1200 –43 dBm/–48 dBm V.21 1180/980 1850/1650 2100 –43 dBm/–48 dBm Origin

Summary of the content on the page No. 11

AN93 2. Modem (System-Side) Device The Si24xx ISOmodem system-side devices contain a controller, a DSP, program memory (ROM), data memory (RAM), UART, SPI and parallel interfaces, a crystal oscillator, and an isolation capacitor interface. The following sections describe the reset sequence, the host interface, the isolation interface, low-power modes, SSI/voice mode and the EEPROM interface. 2.1. Resetting the Device Reset is required after power-on or brownout conditions (the supply dropping

Summary of the content on the page No. 12

AN93 6. Set non-default frequency values—Ring. 7. Set non-default filter parameters. 8. Set non-default S-register values. The modem is now ready to detect rings, answer another modem, call, or dial out to a remote modem. Some key default settings for the modem after reset or powerup include the following:  V.92 and fall-backs enabled (Si2494/93)  V.90 and fall-backs enabled (Si2457)  V.34 and fall-backs enabled (Si2439/34)  V.32bis and fall-backs enabled (Si2415)  V.22bis and fall-backs en

Summary of the content on the page No. 13

AN93 2.1.3. Reset-Strap Options for 16-Pin SOIC Package The clock frequency and interface on the 16-pin SOIC package are selected according to Table 5 below. The parallel interface, EEPROM and autobaud options are not available in the 16-pin SOIC package. Table 5. SOIC-16 Reset-Strap Options Mode Reset-Strap Pins Interface Input Clock Pin 3 Pin 5, RXD/MISO Pin 7, CTS/SCLK Pin 11 Pin 15 RI INT DCD UART 32 kHz 0 X 1 1 X 4.9152 MHz 1 X 1 1 1 27 MHz 1 X 1 1 0 SPI 32 kHz 1 1 X 0 1 4.9152 MHz 0 1 X 0

Summary of the content on the page No. 14

AN93 2.1.4.1. Reset Strapping Options for TSSOP-24 with UART-Interface UART-interface options for the 24-pin TSSOP package are shown in Table 6 below. Table 6. TSSOP-24 UART-Interface Options Mode Reset-Strap Pins Input Clock Autobaud Three-Wire Pin 4 Pin 11, CTS Pin 17 Pin 18 Pin 23 Disabled? EEPROM FSYNC Pin 15, AOUT RI SDI/EESD DCD Interface? Pin 16, INT 32 kHz No No 1 1 0 1 X Yes 0 1 0 1 X Yes No 1 1 0 0 X Yes 0 1 0 0 X 4.9152 MHz No No 1 1 1 1 1 Yes 0 1 1 1 1 Yes No 1 1 1 0 1 Yes 0 1 1 0 1

Summary of the content on the page No. 15

AN93 2.1.4.3. Reset Strapping Options for TSSOP with SPI-Interface Table 8 lists the SPI-interface options for the 24-pin TSSOP package. Table 8. TSSOP-24 SPI-Interface Clock-Frequency Options Mode Reset-Strap Pins Input Clock Three-Wire Pin 4 Pin 9, RXD Pin 16 Pin 17 Pin 23 EEPROM FSYNC Pin 11, SCLK INT RI DCD Interface? Pin 15, AOUT Pin 18, SDI/EESD 32 kHz No 1 1 0 1 1 Yes 0 1 0 1 1 4.9152 MHz No 1 1 0 0 X Yes 0 1 0 0 X 27 MHz No 1 1 0 1 0 Yes 0 1 0 1 0 2.1.5. Reset Strapping Options for QFN

Summary of the content on the page No. 16

AN93 2.1.5.2. Reset Strapping Options for QFN Parts with SPI Operation Table 10 lists the reset strapping options for QFN parts with SPI operation. Table 10. Reset Strapping Options for QFN parts with SPI Operation Input Clk Three-Wire FSYNCH AOUT EECLK INT RI SDI DCD MISO EEPROM Interface Pin 2 Pin 15 Pin 13 Pin 35 Pin 19 Pin 8 Pin 28 Pin 22 32 kHz No 1 1 1 0 1 1 1 1 Yes 0 1 1 0 1 1 1 1 4.9152 MHz No 1 1 1 0 0 1 X 1 Yes 0 1 1 0 0 1 X 1 27 MHz No 1 1 1 0 1 1 0 1 Yes 0 1 1 0 1 1 0 1 2.1.5.3. R

Summary of the content on the page No. 17

AN93 2.2. System Interface The ISOmodem can be connected to a host processor through a UART, SPI or parallel interface. Connection to the chip requires low-voltage CMOS signal levels from the host and any other circuitry interfacing directly. The following sections describe the digital interface options in detail. 2.2.1. Interface Selection The interface is selected during reset, as described in "2.1. Resetting the Device". Tables 12, 13, and 14 show the functions of the affected pins for possi

Summary of the content on the page No. 18

AN93 Table 14. Pin Functions vs. Interface Mode (QFN-38) Pin # UART Mode SPI Mode Parallel Mode 35 INT INT INT 34 GPIO18 GPIO18 D0 33 GPIO17 GPIO17 D1 32 GPIO16 GPIO16 D2 31 GPIO23 GPIO23 D3 30 GPIO24 GPIO24 D4 29 ESC D5 28 DCD D6 24 RTS SS D7 23 TXD MOSI WR 22 RXD MISO RD 21 CTS SCLK CS 20 GPIO11 GPIO11 A0 19 RI 18 Rev. 1.3

Summary of the content on the page No. 19

AN93 2.2.2. Interface Signal Description The following tables describe each set of UART, parallel and SPI interface signals: Table 15. UART-Interface Signals Signal Direction Description TXD Input Data input from host TXD pin RXD Output Data output to host RXD pin RTS Input Active-low request-to-send input for flow control CTS Output Clear to send: Si2493 is ready to receive data on the TXD pin (active low) Table 16. SPI-Interface Signals Signal Direction Description SCLK Input Serial data c

Summary of the content on the page No. 20

AN93 The UART interface synchronizes on the start bits of incoming characters and samples the data bit field and stop bits. The interface is designed to accommodate character lengths of 8, 9, 10, and 11 bits giving data fields of 6, 7, 8, or 9 bits. Data width can be set to 6, 7, or 8 bits with the AT\Bn command. Parity can be set to odd, even, mark, or space by the AT\Pn command in conjunction with AT\B2 or AT\B5. Other AT\Bn settings have no parity. Table 18. DTE Rates Ideal DTE Rate (bps) Act


Alternative user manuals
# User manual Category Download
1 Silicon Laboratories SI2493/57/34/15/04 User manual Modem 1
2 Edelbrock 15631 User manual Modem 0
3 3Com 1.024.1644-00 User manual Modem 0
4 3Com OFFICECONNECT 3C886 User manual Modem 5
5 3Com ADSLEthernet User manual Modem 1
6 3Com CableExternal User manual Modem 6
7 Sony GC75 User manual Modem 2
8 Sony SE366 User manual Modem 3
9 Sony MP595 User manual Modem 1
10 Sony TRUINSTALL USB 598 User manual Modem 1
11 Actiontec electronic Actiontec 1520 User manual Modem 2
12 Actiontec electronic 1524 User manual Modem 0
13 Actiontec electronic DataLink 56K User manual Modem 0
14 Actiontec electronic 56K ISA Lite User manual Modem 0
15 Airlink RAVEN-E EV-DO User manual Modem 0