Summary of the content on the page No. 1
PCI 56Kbps V.92 Data/fax Voice Modem Card
RC403
User Manual
Summary of the content on the page No. 2
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403 User Manual Installation Guide Installation Guide for Windows Series 98/98SE/ME/2000 and XP.........................................2 System Requirements ...................................................................................................... 2 Modem Installation............................................................................................................ 2 Basic AT Command Guide .................
Summary of the content on the page No. 3
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403 User Manual Installation Guide for Windows Series 98/98SE/ME/2000 and XP System Requirements • Computer with Pentium 200 MMX or higher processor. • Windows 98/98SE/ME/2000 and XP Operating System. • 20 MB Hard Disk free space or above • Sound card for voice features • available PCI slot. • CD-ROM drive. Modem Installation . Please turn off your computer and disconnect the power cable. 2. Please remove the cover from your c
Summary of the content on the page No. 4
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403 User Manual Basic AT Command Guide T - Set Tone Dial Default This command forces DTMF dialing until the next P dial modifier or P command is received. The modem will set an S-Parameter bit to indicate that all subsequent dialing should be conducted in tone mode. Note that the DP command will override this command. Clears S4 bit 5. This command may not be permitted in some countries. (See P.) Syntax T Result Codes OK P - Set Pulse Dial Default
Summary of the content on the page No. 5
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403 User Manual Result Codes OK = 0 or . ERROR Otherwise. O - Return to On-Line Data Mode This command specifies that the modem will enter the on-line data mode from the on-line command mode with or without a retrain. If in the off-line command mode when this command is entered, the modem reports ERROR. Syntax O[] Defined Values Decimal number corresponding to the selected option. 0 Enters on-line data mode from the on-l
Summary of the content on the page No. 6
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403 User Manual &V - Display Current Configuration and Stored Profile This command reports the current (active) configuration and the stored (user) profiles. Syntax &V Result Code OK Example: AT&V ACTIVE PROFILE: E L M Q0 T V X0 &C &D2 &G0 &T0 S00:000 S0:000 S02:043 S03:03 S04:00 S05:008 S06:004 S07:050 S08:004 S0:04 S2:050 S6:000 S8:000 S29:070 STORED PROFILE 0: E L M Q0 T V X4 &C &D2 &G0 &T0 S00:000 S02:043 S06:004 S07:050 S08:
Summary of the content on the page No. 7
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403 User Manual the *B command. The format of the response is shown by the example below (delay times are shown as hours:minutes:seconds). If no numbers are delayed, only the OK result code is issued. Example: NO. - PHONE NUMBER -DELAY ------ ------------------------------------------- ; 8264734660 2:00:00 2; 753263466 2:00:00 3; 2587334662 0:02:00 4; 753265663 0:03:25 5; 745993664 0:0:45 OK V.92 +P and –Q Commands This section describes the +P
Summary of the content on the page No. 8
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403 User Manual state of a negotiated handshake with a V.92-compliant server in V.92 Mode. Syntax +PMH= Defined Values Decimal number corresponding to the selected operation. 0 Modem-on-hold enabled in V.92 Mode. (Default.) Disabled modem-on-hold. Result Codes OK 0 or in V.92 Mode ERROR Otherwise. Reporting Current or Selected Value Command: +PMH? Response: +PMH: Example: +PMH: 0 For the default setting. Reporting Su
Summary of the content on the page No. 9
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403 User Manual 3 Grant MOH with indefinite timeout Result Codes OK 0-3 in V .92 Mode (+MS=V92) ERROR Otherwise Reporting Current or Selected Values Command: +PMHT? Response: +PMHT: Example: +PMHT: 0 For the default setting. Reporting Supported Range of Parameter Values Command: +PMHT=? Response: +PMHT: ( range) Example: +PMHT: (0,,2,3,4,5,6,7,8,9,0,,2, 3) Please register your product at www.rosewill.com for complete
