Summary of the content on the page No. 1
Models
HL120 ML-134296
HL200 ML-134331
HL200 ML-134289
PRIOR ML’S COVERED IN THIS CATALOG
HL200 ML-134308
INSTRUCTION MANUAL
701 S. RIDGE AVENUE TROY, OHIO 45374 -0001
937-332-3000 · W W W.HOBARTCORP.COM
F34922 Rev. B (May 2006)
Summary of the content on the page No. 2
TABLE OF CONTENTS GENERAL...............................................................................................3 INSTALLATION...............................................................................................3 Unpacking .............................................................................................3 Location ................................................................................................3 Electrical Connections .........................
Summary of the content on the page No. 3
Installation, Operation and Care of TM Legacy 12 & 20-Quart Mixers SAVE THESE INSTRUCTIONS GENERAL The Legacy 12-quart mixer is a bench-type mixer which features a SmartTimer™, a manual bowl lift and a #12 attachment hub as standard equipment. The Legacy 20-quart mixer is a bench-type mixer which features a SmartTimer™, a manual bowl lift and a #12 attachment hub as standard equipment. With the use of special agitators, a 12 quart bowl may be used on the HL200 mixer. A variety of a
Summary of the content on the page No. 4
ELECTRICAL CONNECTIONS (Cord Connected Mixers) WARNING: THE ELECTRICAL CORD ON THIS MACHINE IS EQUIPPED WITH A THREE- PRONGED GROUNDING PLUG WHICH MUST BE CONNECTED TO A PROPERLY GROUNDED RECEPTACLE. IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT REMOVE THE GROUNDING PRONG FROM THE PLUG. WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTION OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. Check Ini
Summary of the content on the page No. 5
OPERATION WARNING: MOVING AGITATOR IN BOWL. KEEP HANDS, CLOTHING, AND UTENSILS OUT OF BOWL WHILE IN OPERATION. DO NOT USE WITHOUT INTERLOCKED GUARD. TM The Legacy mixer is equipped with SmartTimer controls. Refer to Fig. 1 for operating parts and OPERATION section for their functions. The bowl guard wire cage must be in closed position or the mixer will not operate. The bowl must remain in mix position on bowl support and the bowl support must be raised (mix position) or the mixer wil
Summary of the content on the page No. 6
Standard Controls Models HL120/HL200 (With Three Mix Speeds Plus Stir Speed) DISPLAY MIXING TIME STOPS MIXER TIME SELECTOR STARTS MIXER SPEED SELECTOR Fig. 2 HL120/HL200 Mixer Speeds STIR (Slow) The lowest speed is for incorporating ingredients. SPEED 1 (Low) This speed is for heavy mixtures such as pizza dough, heavy batters and potatoes. SPEED 2 (Medium) This speed is for mixing cake batters, mashing potatoes and developing bread dough. SPEED 3 (H
Summary of the content on the page No. 7
Recipe Timer (Optional) Models HL120/HL200 (With Three Mix Speeds Plus Stir Speed) Fig. 15 The SmartPlus2™ recipe timer has two operating modes, Standard (STD) and RECIPE. Standard Mode Operates exactly as the standard controls utilizing continuous and timed mixing. Recipe Mode • Use mode buttons to switch mixer operation between recipe and standard timed operation. • Up to 4 recipes can be stored in memory • Each recipe can contain 5 steps • Each step can be programmed to operate
Summary of the content on the page No. 8
BOWL PLACEMENT The bowl must be installed before the agitator is installed. To install the bowl, lower the bowl support and position bowl so the alignment pins on the left side of the bowl support fit in the holes in the bowl tab. (Fig. 3) Place the slotted tab on bowl into the lower part of the pin. Swing the bowl into the mix position on bowl support. (Fig. 4) Fig. 3 AGITATOR Fig. 4 To install an agitator, the bowl must be on the bowl support. To Install 1. Lower the bowl
Summary of the content on the page No. 9
PREPARE FOR MIXING 1. Place the mixing bowl on the bowl support. 2. Pour ingredients into the bowl. 3. Swing the bowl back to the mix position. 4. Place the agitator inside the bowl, and then attach it to the agitator shaft (Fig. 6). 5. Lift bowl support. 6. Correctly close the bowl guard wire cage. 7. The mixer is now ready for mixing. (See TIMER OPERATION.) Fig. 6 STANDARD TIMER OPERATION Using the Count-Up Mode (Continuous Mixing) 1. Turn the SPEED dial to select a mix spe
Summary of the content on the page No. 10
Using the Count-Down Mode (Timed Mixing) 1. Turn the SPEED dial to select a mix speed. a. If the count-up mode was used for the previous batch, the desired time needs to be entered. b. If the count-down mode was used for the previous batch, the previous time will be displayed. If a different time is needed, turn the TIME selector to the desired time in 10 second increments. 2. Press the START button to begin mixing; the timer starts counting down from the set time. a. To stop the mixer a
Summary of the content on the page No. 11
RECIPE TIMER OPERATION Recipe Timer Notes • If pause is selected as a mix speed, the mixer START button must be pressed to advance to the next recipe step after the pause time has expired. • If pause has been selected, the bowl guard can be opened and the time will continue to count down. • The recipe step can be interrupted and then resumed by pressing the STOP button and then the START button. NOTE: If PAUSE has been selected, the STOP button is disabled. • The r
Summary of the content on the page No. 12
View Recipe When the mixer is in RECIPE mode, you can view the step settings of any recipe. 1. Press the SELECT/SAVE button. A. Display will alternate between speed and time. B. The LED of the step being displayed will flash. 2. Use the arrow buttons to view the next step. 3. Use the Recipe selector to view other recipes. 4. Press PGM button to return to the RECIPE mode. NOTE: If the mixer is performing a recipe, the recipe will continue to operate in normal recipe mode sequence.
Summary of the content on the page No. 13
NOTES: • If a value has been assigned for a step number, that LED will be lit. • The LED for the selected step will blink. • If the default value is still assigned to a step, the LED will not be lit. • When programming, the Recipe and Time Selectors are disabled. SPEED SETTINGS TIME SETTINGS SPd 1 (DEFAULT) 00:00 – 15:00 minutes (10 second increments) SPd 2 End (default) SPd 3 Stir PAUS (pause – no mixing) 5. Use arrows to select step number (1 – 5). 6. Press SPEED. All charac
Summary of the content on the page No. 14
UNLOADING 1. Open the bowl guard wire cage assembly. 2. Lower bowl support. 3. Remove the agitator from the agitator shaft. 4. Slightly lift the bowl off the pin (right side), pull bowl to the front and remove from the bowl support (left side). WIRE CAGE The bowl guard wire cage can be rotated out of the way to add ingredients or to access the bowl and agitator. Note how the plastic carriers allow the wire cage to ride around the circumference of the planetary drip cup. • Open
Summary of the content on the page No. 15
Remove and Clean Bowl Guard Wire Cage (Fig. 11) 1. Rotate wire cage to your left until the three carriers align with the carrier escape slots in the circular ridge of the planetary drip cup. 2. Lift the wire cage straight up so the carriers escape from the slots on the drip cup. The bowl guard wire cage can now be removed by pulling toward you. Escape Slots (3) Fig. 11 3. Wash the bowl guard wire cage in a sink, rinse with clear water, and dry wit
Summary of the content on the page No. 16
AGITATORS AND ATTACHMENTS Attachments for attachment hub and agitators are covered in a separate Hobart Legacy Mixer Use and Application Handbook on the Mixer Operator Information CD. Follow the instructions accordingly. Available Agitators and Attachments 12 & 20 Qt. B Flat Beater 12 & 20 Qt. D Wire Whip 12 & 20 Qt. ED Dough Hook 20 Qt. E Dough Hook 12 & 20 Qt. SST Bowl 12 & 20 Qt. Scraper 12 & 20 Qt. Splash Cover 12 & 20 Qt. C Wing Whip 16
Summary of the content on the page No. 17
12 & 20 Qt. P Pasty Knife 12 & 20 Qt. Ingredient Chute 12 & 20 Qt. Table CLEANING WARNING: UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY CLEANING PROCEDURES. The mixer should be thoroughly cleaned daily. DO NOT use a hose to clean the mixer; it should be washed with a clean, damp cloth. The base allows ample room for cleaning under the mixer. The apron (Fig. 1) may be removed for cleaning by loosening the screws. The drip cup (Fig. 1) should be removed (which is secu
Summary of the content on the page No. 18
MAINTENANCE WARNING: UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY MAINTENANCE PROCEDURES. Slideway Planetary Seal Fig. 12 Fig. 13 LUBRICATION Slideways The slideways (Fig. 12) should be lubricated approximately twice a year. To reach these areas, fully lower the bowl support and remove the apron, which is secured by slotted screws. Wipe a thin coat of Lubriplate 630AA on the bowl pad area of the bowl supports and on each slideway. Install the apron. Planetary Seal
Summary of the content on the page No. 19
ADJUSTMENTS Agitator Clearance The agitator clearance should be checked periodically. The agitator must not touch the bowl and the maximum clearance between the bottom of the bowl and the B flat beater is 1/8" (3 mm); the maximum clearance between the bottom of the bowl and the ED dough arm is 5/16” (8 mm). Install a bowl and agitator (e.g., beater). If the bowl and beater come into contact before the bowl support reaches its stop, adjust the stop screws. Refer to Adjust the Bowl/Agitato
Summary of the content on the page No. 20
TROUBLESHOOTING Symptoms Possible Causes Flashing Time Display – See Below Mixer will not start Branch circuit protector is in open position - check fuse or disconnect switch. Mixer is overloaded. Wire cage is not in the closed position. Bowl is not in closed (mix) position or if Bowl in not in up position. Bowl is not in closed (mix) position. Agitator touches bowl Improper agitator clearance - see Maintenance for adjustment procedure. Agitator is not installed properly Sea
