Gilson MORTAR-PLASTER 1200MP user manual

User manual for the device Gilson MORTAR-PLASTER 1200MP

Device: Gilson MORTAR-PLASTER 1200MP
Category: Mixer
Manufacturer: Gilson
Size: 0.64 MB
Added : 11/2/2014
Number of pages: 30
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Gilson MORTAR-PLASTER 1200MP. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Gilson MORTAR-PLASTER 1200MP.

For your convenience

If looking through the Gilson MORTAR-PLASTER 1200MP user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Gilson MORTAR-PLASTER 1200MP on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Gilson MORTAR-PLASTER 1200MP to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Gilson MORTAR-PLASTER 1200MP User manual - Online PDF
Advertisement
« Page 1 of 30 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Gilson MORTAR-PLASTER 1200MP but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Gilson MORTAR-PLASTER 1200MP. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

GILSJ JN MIXERS
MORTAR-PLASTER MIXER
MODEL: 1200MP
OPERATOR’S GUIDE & PARTS MANUAL
GILSJ JN MIXERS
4343 Easton Road · St. Joseph, MO 64503
BY
816-233-4840 · 800-253-3676
Fax 816-233-4624 · 888-253-3676
E-Mail: cleform@ccp.com
Web Address: www.cleform.com

Summary of the content on the page No. 2

INTRODUCTION This operator’s manual has been prepared to provide the information you need to correctly operated and maintain your mixer. For maximum satisfaction, carefully read and follow the instructions in this manual. Should you need repair parts or service, refer to the parts breakdown on pages 14 through 27. Information regarding operation and maintenance of the factory-installed engine or motor can be found in a separate engine/motor owner’s manual supplied with the mixer. The manual p

Summary of the content on the page No. 3

TABLE OF CONTENTS 1. SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 2. ASSEMBLY AND PREOPERATIONAL CHECKS . . . . . . . 4 3. CONTROLS AND OPERATION Clutch Control Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Tow Pole Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4. MIXER TRANSPORT . . . . . . . . . . . . . . . . . . . . . . . . .

Summary of the content on the page No. 4

1 – SAFETY PRECAUTIONS THE FOLLOWING PRECAUTIONS ARE SUGGESTED TO HELP PREVENT ACCIDENTS. A CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS CAN BE AVOIDED BY OBSERVING CERTAIN PRECAUTIONS. READ AND PRACTICE THE FOLLOWING PRECAUTIONS BEFORE OPERATING THIS EQUIPMENT TO HELP PREVENT ACCIDENTS. EQUIPMENT SHOULD BE OPERATED ONLY BY THOSE WHO ARE RESPONSIBLE AND HAVE BEEN PROPERLY INSTRUCTED.  Read all operating and maintenance instruction before operating or servicing the mixer. Test run th

Summary of the content on the page No. 5

 Never charge or fill the unit prior to starting the mixing blades as an overload encountered in starting a loaded unit could damage the engine/motor or drive components.  Connect safety chains as instructed when towing the mixer. Connect only to correct hitch or coupler.  Keep warning, caution and safety instruction labels clean and in good condition. Replace missing, damaged or illegible labels. 2 – ASSEMBLY AND PRE-OPERATIONAL CHECKS The only assembly required on this mixer is the install

Summary of the content on the page No. 6

3 – CONTROLS AND OPERATIONS 1. The mixing paddles feature adjustable rubber wipers and steel backing plates. Paddles are factory preset for appropriate drum wrap clearance. If adjustment is required, proceed as follows: A. Loosen the wiper attaching hardware and move the wiper outward to maintain contact with the drum but without folding over when in operation. B. After adjustment, turn the mixer arms one full turn manually to check clearance and eliminate the possibility of wiper back plates c

Summary of the content on the page No. 7

TOW POLE ASSEMBLY The tow pole assembly is located on the front of the mixer and is used for transport only. For transport, pull the tow pole assembly out, line up the hold and insert the L-shaped pin through holes. When operating the mixer, pull the L-shaped pin out of the hole and push tow pole assembly all the way in. Line up the holes and insert the L-shaped pin through the holes. SAFTEY CHAINS 1. Cross chains under the tow pole when connecting the safety hooks to the tow pole. SEE FIGURE 2

Summary of the content on the page No. 8

4 – MIXER TRANSPORT 1. Secure drum by engaging drum lock. 2. Secure all moveable parts, including the rear housing. 3. Secure tow pole coupler to vehicle and attach safety chains and hooks. (See FIGURE 2, Safety Chains). A. Pintle type couplers require the appropriate tow vehicle coupler retainer. B. Match ball coupler size exactly with hitch ball. 5 – OPERATING THE MIXER STARTING THE MIXER Start the mixer engine/motor. Refer to the engine/motor manual for proper starting procedures. When the

Summary of the content on the page No. 9

LOADING THE MIXER When the mixing blades are rotating, pour the required amount of water into the drum, then add cement, sand and lime. The desired mixing speed is 33 RPM. DISCHARGING THE MIXER Allow the entire mixture to mix for one (1) full minute. DO NOT STOP MIXER FROM ROTATING. Hold the tilt handle and disengage the drum lock. Dump mortar to the side by pulling the tilt lever downward. After the mixture is dumped, return the drum to the operating position and engage drum lock. CLEANING

Summary of the content on the page No. 10

TROUBLE SHOOTING GUIDE FOR MP MIXERS. ENGINE WON’T START: 1. Check for sufficient fuel. 2. Check oil level (some engines have an oil alert, preventing the engine from starting when oil level is low) 3. Was engine choked when starting? 4. Is engine flooded? 5. Check spark plug. (Clean and check gap). 6. If engine still won’t start, take to service center. BELT DRIVEN MODELS: 1. Check condition of belts, replace if necessary. 2. Check for oil or grease on belts as well as for loose belts. 3. Adjus

Summary of the content on the page No. 11

6 – OPERATING GUIDELINES MASONRY CONSTRUCTION GUIDELINES The strength and durability of brick masonry depends upon the quality of the brick, the quality of the mortar and the workmanship in laying. The strength also depends upon adequate bond and the shape of the masonry unit. Brick quality – Characteristics are hardness and density. Brick for masonry which is exposed to weather or where strength is desired should have a crushing strength of not less than 2500 PSI. Laying and bonding – Brick s

Summary of the content on the page No. 12

7 – LUBRICATION DRUM SEAL HOUSINGS Drum seals are provided on each end of the drum where the mixing shaft passes through to the bearings. It is important to pump grease into the housings through use to retain seal efficiency. Use enough grease to flush out old grease and carry away any grit. Use lithium based grade 2 multi-purpose grease. SEE FIGURE 3 MIXING SHAFT BEARINGS The mixing shaft bearings are permanently factory sealed and lubricated, and should not require further service. WHEEL B

Summary of the content on the page No. 13

DRUM SHAFT BEARING HANGERS Drum yoke bearing hangers are located on each side of the drum, and are equipped with grease fittings. These bearings should be lubricated once each week with lithium based grade 2 multi-purpose grease. ENGINE/MOTOR Refer to the engine/motor operating instructions for all maintenance and lubrication instructions and requirements. JACK SHAFT BEARINGS Pillow block style bearing are used on the drive train counter-shaft. See Drum Seal Housing, Lubrication Guidelines for

Summary of the content on the page No. 14

ENGINE/MOTOR DRIVE SEE FIGURE 4. 1. Align pulleys correctly 2. Tighten locking collars in the direction of rotation and tighten setscrews. 3. Adjust tension on the engine belt as follows: A. Place clutch lever in the engaged (drive) position. B. Move the engine/motor to tighten the belt until the engine plate is slightly above the horizontal position (about 1-2 degrees). Tighten engine/motor securely. 4. Adjust belt fingers so they do not touch the belt when the drive is engaged, but must allow

Summary of the content on the page No. 15

14

Summary of the content on the page No. 16

Concrete Mixer Parts List REF NO. PART NO. DESCRIPTION QTY DRUM & DRIVE 1 232444 Bearing Hanger 2 2 1031 Grease Fitting 4 3 232478 Gear (Gasoline Powered Models) 1 245498 Gear (Electric Powered Models) 1 4 245466 Drum Shell Assembly 1 5 245459 Grill Assembly 1 6 232459 Bearing Support Assembly 2 7 5126 Drum Tilt Lever 1 8 232465 Drum Seal 2 9 5095 Seal Housing 2 10 5097 Seal Retainer 2 11 232573 Shaft Seal 2 12 232462 Bearing, Drum Shaft (comes w/232463) 2 13 245477 Drum Shaft 1 14 232463 Locki

Summary of the content on the page No. 17

16

Summary of the content on the page No. 18

Concrete Mixer Parts List MIXING BLADES REF NO. PART NO. DESCRIPTION QTY 1 245460 Mixing Arm Assembly, Engine End 2 2 245463 Mixing Arm Assembly, Tow End 2 3 245461 Mixing Arm Cap 4 4 5585 Drum Wrap Wiper 4 5 5643 Wrap Wiper Backing Plate 4 6 5088 End Wiper Backing Plate 2 7 5089 Drum End Wiper 2 8 *71195 Capscrew, Hex HD 5/8-11 x 2 Gr 5 10 9 *70249 Capscrew, Hex HD 3/8-16 x 1 1/2 Gr 5 16 10 *70567 Nut, Hex 5/8-11 10 11 *70553 Nut, Hex 3/8-16 20 12 *70657 Washer, 5/8 Spring Lock 10 13 *70649 Wa

Summary of the content on the page No. 19

18

Summary of the content on the page No. 20

Concrete Mixer Parts List ENGINE HOUSING AND AXLE REF NO. PART NO. DESCRIPTION QTY 1 245471 Engine Housing Assembly w/decals 1 2 245470 Housing Base Assembly 1 3 32082 Reflector 2 4 232623 T-Handle Latch 2 5 5402 Handle, Engine Housing 1 6 220521 Rivet, Handle 4 7 223590 Rubber Bumper 4 8 232614 Housing Base Front Plate 1 9 213297 Screw, Thread Forming 5/16-18 x 1/2 6 10 *29065 Screw, Sheet Metal #10-24 x 3/8 4 11 232489 Axle Assembly 1 12 38565 Hub Assembly (includes:) 2 13 1046 Bearing Cup


Alternative user manuals
# User manual Category Download
1 Gilson MORTAR-PLASTER 600MP User manual Mixer 0
2 Gilson 51/2CU.FT. 59015C User manual Mixer 2
3 Gilson 600CM User manual Mixer 0
4 Edelbrock 15621 User manual Mixer 0
5 Sony Atrac3/MP3 CD Walkman D-NE300 User manual Mixer 51
6 AMF Stationary Bowl(SBM) User manual Mixer 3
7 AMF Offset Tilt Bowl(OTBM) User manual Mixer 7
8 AMF Glen 340 User manual Mixer 39
9 AMF None User manual Mixer 1
10 AMF TILT Bowl(TBM) User manual Mixer 4
11 AMF U2 User manual Mixer 3
12 Analog Devices AD8342 User manual Mixer 0
13 Avanti ProductsCK3016 User manual Mixer 0
14 Black & Decker GM200 User manual Mixer 19
15 Black & Decker M200P User manual Mixer 3