Summary of the content on the page No. 1
MODEL T10050
RIGHT ANGLE
IRON BENDER
INSTRUCTIONS
Damage to your eyes, face, and hands could
result from using this item without proper
protective gear, such as safety glasses or a
face shield, and gloves.
Figure 1. Model T10050.
Inventory (Figure 2)
A. Bender (not shown) .................................... 1
B. Bender Handle ........................................... 1
C. Work Stop Rod ........................................... 1
D. Hex Bolts M10-1.5 x 40 (Handle) ............... 2
B
C
E
Summary of the content on the page No. 2
Identification Work Stop Clamp Cam Shaft Clamp die Bending plate Bending Work Stop Rod plate Knob Handle angle Stop Figure 3.. identification. Illustration Legend (Figure 4) Throughout these instructions, diagrams are used to illustrate how the components of the machine are used during the various steps of operation. Familiarize yourself with the following illustration, its relationship to the machine, and the sym- bols used in it before proceeding through these instructions. F
Summary of the content on the page No. 3
3.. Thread the work stop knob into the work stop, Assembly then slide the work stop onto the work stop rod (Figure 7). The Model T10050 requires only minimal assem- bly before use. Work Stop To assemble the machine: 1.. Connect the bender handle to the machine with the M10-1.5 x 40 hex bolts and 10mm flat washers (Figure 5). Hex Bolt Work Stop Rod x2 Knob Figure 7.. Work stop. Flat Washer Handle Figure 5.. Attaching handle. 2.. insert the stop rod with the M12-1.75 hex nut into the base.
Summary of the content on the page No. 4
Mounting Operations once you have confirmed that your machine is Creating Bends assembled and functioning properly, mount it to a 1.. lift the clamp cam shaft to release the clamp workbench through the holes in the base. Be sure die. Rotate the clamp die as necessary to the workbench will remain stable when bending accommodate the thickness of your work- force is applied to the machine. if necessary, piece, then slide the clamp cam shaft back anchor the workbench to a wall or the floor
Summary of the content on the page No. 5
2.. place the workpiece into the clamp and adjust 4.. use the handle to bend the workpiece to the the workpiece position as needed. Rotate the desired angle (Figure 14). clamp cam shaft to clamp the workpiece (Figure 12). Figure 14.. Bending workpiece. Figure 12.. Clamping workpiece. 5.. loosen the bending plate and clamp cam shaft to release the workpiece (Figure 15). —if the clamp die does not move far enough to fully clamp the workpiece, repeat Steps 1 & 2. 3.. adjust the bending plate
Summary of the content on the page No. 6
2.. Bend the workpiece to the desired angle, Repetitive Bends then slide the angle stop against the bender base. Turn the angle stop to lock it in position (Figure 17). To ensure consistent and accurate bends when performing multiple, identical operations, use the work stop and angle stop. To use the work stop and angle stop: 1.. place the workpiece in the machine as need- ed, then slide the work stop against the end of the workpiece. Tighten the work stop knob (Figure 16). Figure 17..
Summary of the content on the page No. 7
parts Breakdown & List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PT10050001 BODY 15 PT10050015 WORK STOP 2 PT10050002 CRANK 16 PT10050016 WORK STOP ROD 3 PT10050003 HANDLE 17 PSW03-1 KNOB M10-1.5 x 35 4 PT10050004 STATIONARY JAW 18 PT10050018 PLASTIC GRIP 5 PT10050005 BENDING PLATE 19 PB31M HEX BOLT M10-1.5 X 40 6 PT10050006 BENDING PLATE KNOB 19-1 PW04M FLAT WASHER 10MM 7 PT10050007 BENDING PLATE LEADSCREW 20 PSB14M CAP SCREW M8-1.25 X 20 8 PT10050008 CLAMP DIE
Summary of the content on the page No. 8
