Summary of the content on the page No. 1
Household Appliances
Over-the-Range Microwave
Installation Instructions
For Models: HMV9302, HMV9305, HMV9306, HMV9307
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING
IMPORTANT: Save these instructions for the local electrical inspector’s use.
INSTALLER: Please leave these Installation Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Summary of the content on the page No. 2
YOUR SAFETY FIRST BEFORE YOU START • Proper installation is the installer's responsibility! – Read the entire manual before you begin. The Model number label is located on the oven front. See Figure 1. Mounting plate is located on back side of microwave oven. See Figure 2. BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS: Model Number Label Mounting plate ( Remove from oven to install. ) Back of oven Figure 1 Figure 2 WARNING FOR YOUR SAFETY: • You will need TWO people to install this oven.
Summary of the content on the page No. 3
Summary of the content on the page No. 4
YOUR SAFETY FIRST • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. – Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath. – ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud. – DO NOT mount the microwave oven to an island or peninsula cabinet. – BE SURE the upper cabinet and rear wall structures are able to support 150 lbs., p
Summary of the content on the page No. 5
Summary of the content on the page No. 6
PARTS, TOOLS, MATERIALS YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION: Carton or other heavy material for covering the counter top. Clear tape Stud finder or thin nail. (for taping the templates to the wall) Keyhole saw (for the power cord hole) Saber saw (for cutting vent holes for roof or wall venting) Electric drill Phillips screwdriver 3/8" and 3/4" wood drill bits 1/2" and 3/16" drill bits Pencil Plumb line Flat blade screwdriver Duct Tape Measuring tape (metal prefer
Summary of the content on the page No. 7
STEP 1: PREPARE THE ELECTRICAL CONNECTIONS WARNING AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 4 Detail. Upper NOTE: The outlet should be on a circuit dedicated to the Cabinet microwave oven 120V, 60Hz., AC only with a 15 or 20A fused electrical supply. IMPORTANT: If you do not have the proper wall outlet, you Grounded Outlet MUST have one installed by a qualified ( Insid
Summary of the content on the page No. 8
STEP 2: PREPARE THE VENTING SYSTEM NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 9, page 9. WARNING:FIRE HAZARD THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways: 1 Roof-venting If your oven is located on an outside wall near the roof, as in Figures 5 (3 /4" x 10" duct) and 8 (6" round duct.) Wall-venting If your oven is located on an outside wall on the first floor
Summary of the content on the page No. 9
STEP 2: PREPARE THE VENTING SYSYTEM STANDARD FITTINGS NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper’s sticking. DUCT LENGTH The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not exceed the equivalent of 140 feet. For best performance, do not use more than three 90 degree elbows. Below
Summary of the content on the page No. 10
STEP 3: PREPARE THE VENTING BLOWER Your microwave oven is shipped with the blower assembled for roof venting. You need to adjust the blower if you want wall-venting or room-vented (recirculating) installation. WARNING ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT. • DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in electrical shock. REMOVE THE MOUNTING PLATE: 1. Remove any shipping materials and parts from inside A thick, protective t
Summary of the content on the page No. 11
Summary of the content on the page No. 12
STEP 3: PREPARE THE VENTING BLOWER blower plate mounting screws exhaust ports blower unit exhaust ports Figure 17 blower unit mounting screws Figure 18 ROOM-VENTED (Recirculating) INSTALLATION: 1. Remove one blower unit mounting screw and one blower plate screw. Remove the blower plate from blower unit cabinet. See Figure 19. 2. Carefully lift the blower unit out of the microwave oven. blower plate mounting screws 3. Rotate blower unit 90˚ so the exhaust ports face the front of the cabinet. See
Summary of the content on the page No. 13
STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION MEASURE AND TACK / TAPE UP THE TEMPLATES 1. Using a plumb line and (metal) measuring tape, find and mark the vertical center line on the back wall, as in Figure 22. 2. Find and mark one or two points where the studs are on the wall (Studs are normally 16 inches apart) and then measure and mark the stud locations. If you cannot find any wall stud, consult a local building contractor. CAUTION DO NOT ATTEMPT TO INSTALL THE MICROWAVE OVEN I
Summary of the content on the page No. 14
STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION DRILLING THE HOLES IN THE WALL AND UPPER CABINET: WARNING BE VERY CAREFUL WHEN DRILLING HOLES INTO THE WALL. Electrical wires could be concealed behind the wall covering and if the drill hits them you could get an electric shock. 1. Find the points on the mounting plate labeled A, B, C, and D. Drill a 3/16" diameter hole at any of these points that are in front of a wall stud. Drill a 3/4" diameter hole at any of these points that are o
Summary of the content on the page No. 15
STEP 5: INSTALL THE MOUNTING PLATE TO THE WALL CONNECTING THE OVEN TO A WALL STUD: 3/16" Hole on Studs 3/4" Hole on Drywall Only NOTE: The oven must be connected to at least one wall stud. Minimum 66" From the Floor 1. Draw a vertical line on the wall at the center of the 30″ For Wall- Vented Only wide space. Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are against the bottom of the cabinet. Line up the notch and cente
Summary of the content on the page No. 16
STEP 5: INSTALL THE MOUNTING PLATE TO THE WALL TO PREPARE THE REAR WALL CUTOUT OPENING AND EXHAUST ADAPTOR/MOUNTING PLATE FOR WALL-VENTED: 1. Place the mounting plate against the rear wall as described in step 5 item 1 (page 15). 2. Using a pencil, put dots through slots F and G, and through holes H and I. Remove the mounting plate and draw lines extending through the points. This will give the location and size of the box cutout for the rear wall Figure 28 duct. See Figure 28. • Attach the ex
Summary of the content on the page No. 17
Summary of the content on the page No. 18
STEP 6: ATTACH THE OVEN TO THE WALL 5. Roof vented installation: See Figure 32 Install ductwork through the vent opening in the upper damper cabinet. Complete the venting system through the roof according to the method needed. See “PREPARE THE VENTING SYSTEM,” step 2 on the page 8. Use caulking to seal exterior roof opening around the exhaust cap. See Figure 6 on page 8. Figure 32 6. Use power supply cord clamp to bundle the power supply cord. Install the power supply cord clamp, using a screw
Summary of the content on the page No. 19
Installation Notes
Summary of the content on the page No. 20
Printed in Korea P/No.: 3828W5U0310
