Summary of the content on the page No. 1
Gravimetric Slide Gate Auger Batch Blender
Red-Lion Display
Models: BD, CSG, SGBD
Part Number: 882.02148.00
Bulletin Number: BLN1-600A
Effective: February 1, 2013
Write Down Your Serial and Software Revision Numbers Here For Future Reference:
_________________________ _________________________
_________________________ _________________________
_________________________ _________________________
We are committed to a contin
Summary of the content on the page No. 2
Shipping Info Unpacking and Inspection You should inspect your equipment for possible shipping damage. Thoroughly check the equipment for any damage that might have occurred in transit, such as broken or loose wiring and components, loose hardware and mounting screws, etc. In the Event of Shipping Damage According to the contract terms and conditions of the Carrier, the responsibility of the Shipper ends at the time and place of shipment. Notify the transportation company’s local agent i
Summary of the content on the page No. 3
Returns Do not return any damaged or incorrect items until you receive shipping instructions from the shipping department. Credit Returns Prior to the return of any material, authorization must be given by the manufacturer. A RMA number will be assigned for the equipment to be returned. Reason for requesting the return must be given. ALL returned material purchased from the manufacturer returned is subject to 15% ($75.00 minimum) restocking charge. ALL returns are to be shipped prepaid.
Summary of the content on the page No. 4
Table of Contents CHAPTER 1:
SAFETY ................................................................ 7
1-1
How to Use This Manual .............................................................................................. 7
Safety Symbols Used in this Manual ..................................................................... 7
1-2
Warnings and Precautions ......................................................................................... 10
1-3
Respons
Summary of the content on the page No. 5
Floor Mount (Central Blender) ............................................................................ 39
3-3
Electrical Connections ................................................................................................ 39
3-4
Pneumatic Connections .............................................................................................. 41
3-5
Initial Set-up ................................................................................................
Summary of the content on the page No. 6
Mixer Sub-Assembly ........................................................................................... 87
Hopper Sub-assembly ......................................................................................... 89
Hopper R.A.M. (Regrind Auger Metering) Sub-Assembly (Optional) .................. 90
Weigh Hopper Sub-assembly ............................................................................. 92
Slide Gate Sub-assembly .........................................
Summary of the content on the page No. 7
Chapter 1: Safety 1-1 How to Use This Manual Use this manual as a guide and reference for installing, operating, and maintaining your blender. The purpose is to assist you in applying efficient, proven techniques that enhance equipment productivity. This manual covers only light corrective maintenance. No other maintenance should be undertaken without first contacting a service engineer. The Functional Description section outlines models covered, standard features, and safety feature
Summary of the content on the page No. 8
Figure 1: Safety Tags and Warning Labels Hazard Alert Symbol Description/Explanation Preventative Maintenance Pinch point slide gate. Every month inspect the Hands can become shears/blades for any type of entangled or cut if they wear. For further information enter the danger zone of see the Maintenance Chapter gears or cutting shears. in this manual. High voltage inside Every six months inspect all enclosure. The electrical electrical connections for enclosure is supplied with sec
Summary of the content on the page No. 9
Mandatory Symbol Description/Explanation Read Operators Manual. This equipment must be operated and maintained by properly trained personnel. The information contained within this manual must be read and understood prior to operating this equipment. Lifting point. Heavy load can fall and cause serious injury or possible death. Lift equipment at designated points. Disconnect before opening. Before servicing or maintaining the machine be sure to disconnect the power and/or compre
Summary of the content on the page No. 10
1-2 Warnings and Precautions Our equipment is designed to provide safe and reliable operation when installed and operated within design specifications, following national and local safety codes. This may include, but is not limited to OSHA, NEC, CSA, SPI, and any other local, national and international regulations. To avoid possible personal injury or equipment damage when installing, operating, or maintaining this equipment, use good judgment and follow these safe practices: þ Read and
Summary of the content on the page No. 11
1-3 Responsibility These machines are constructed for maximum operator safety when used under standard operating conditions and when recommended instructions are followed in the maintenance and operation of the machine. All personnel engaged in the use of the machine should become familiar with its operation as described in this manual. Proper operation of the machine promotes safety for the operator and all workers in its vicinity. Becoming familiar with materials, inspection, speed lim
Summary of the content on the page No. 12
Learn and always use safe operation. Cooperate with co-workers to promote safe practices. Immediately report any potentially dangerous situation to your supervisor or appropriate person. REMEMBER: • NEVER place your hands or any part of your body in any dangerous location. • NEVER operate, service, or adjust the blender without appropriate training and first reading and understanding this manual. • NEVER try to pull material out of the blender with your hands while it is running! Before
Summary of the content on the page No. 13
Maintenance Responsibility Proper maintenance is essential to safety. If you are a maintenance worker, you must make safety a priority to effectively repair and maintain equipment. Before removing, adjusting, or replacing parts on a machine, remember to turn off all electric supplies and all accessory equipment at the machine, and disconnect and lockout electrical power. Attach warning tags to the disconnect switch. When you need to perform maintenance or repair work on a blender above flo
Summary of the content on the page No. 14
Chapter 2: Functional Description 2-1 Models Covered in This Manual This manual provides operation, installation, and maintenance instructions for the BD, CSG, and SGBD Series slide gate blenders of various blending rates and specifications. See below for a list of available models. • 150 lbs/hr Slide Gate Batch Blender with Allen-Bradley Controls • 500 lbs/hr Slide Gate Batch Blender with Allen-Bradley Controls • 900 lbs/hr Slide Gate Batch Blender with Allen-Bradley Controls • 2500 lb
Summary of the content on the page No. 15
Figure 2: Equipment Specifications Dimensions and Specifications 150 (*1) 500 900 2500 4000 6000 Maximum Blending Rate, lbs/hr (kgs/hr) (*4) 150 (68) 500 (227) 900 (410) 2500 (1135) 4000 (1815) 6000 (2725) Number of Materials to be Blended 2 to 4 2 to 6 2 to 8 Slide Gate Size - Majors, in. (mm) 2.0 (50) 2.0 (50) 2.5 (63) 4.0 (100) Slide Gate Size - Minors, in. (mm) 1.5 (38) 1.5 (38) 2.0 (50) 3.0 (75) Supply Hopper Capacity - Majors, cu.ft. (l.) (*2) 0.7 (20) 1.4 (40) 3.0 (85) 7.5 (212) Supply H
Summary of the content on the page No. 16
2-3 Typical Features and Components Mechanical Features • Exclusive diamond design slide gate metering assemblies meter a large range for free- flowing pellet materials • Adjustable slide gate stroke limiting restrictors provided for accurate metering of minor ingredients (not available on 150 models, or removable hopper components) • Removable stainless steel weigh hopper and mixing components • Powder coated mild steel material supply hoppers with machined polycarbonate clean- out doors
Summary of the content on the page No. 17
• 100 recipe storage book • Three (3) types of recipe entry procedures available: o “EZ Recipe” mode (up to 8-component) recipe entry. Color and additives are metered as a percentage of the virgin material. o Percentage mode recipe entry. Ingredients are metered as a percentage of the overall batch. o Parts mode recipe entry (i.e. 500:1) Ingredients are metered as a ratio to each other within the batch • Full control diagnostics • Serial printer and communications ports System Compo
Summary of the content on the page No. 18
Slide Gates Air operated slide gates are provided to meter the majority of pellet ingredients on Slide Gate blenders. • The metering range assumes 1/8” diameter free-flowing plastic pellets weighing approximately 35 lbs./cu. ft. This is meant to be an approximate sizing recommendation and can vary with different bulk density resins, pellet configuration, etc. A stroke limiter (included) can be installed on the metering gates to limit their travel. This device decreases the stroke of
Summary of the content on the page No. 19
Figure 6: Typical Slide Gate Assembly Each of the diamond gate air cylinders is actuated by a solenoid valve, which are controlled by the blender PLC. When the solenoid valve is energized, it opens the metering valve cylinder. When the solenoid valve is de-energized, it closes the metering valve cylinder. If the power is interrupted to the blender, the metering valves will return to the closed position, to prevent material from over-filling the weigh hopper/mix chamber. • If the blender
Summary of the content on the page No. 20
Figure 7: Typical Weigh Hopper Assembly The weigh hopper dump door holds the material until it is dumped into the mixing section. The cylinder is actuated by a solenoid in the valve stack on the side of the blender. In looking at the pneumatic circuit, you can see that the air regulator controls the flow of air to the valve stack. When the weigh hopper discharge cylinder solenoid valve is not electrically energized, it will provide air pressure to the air cylinder and hold the shaft
