Summary of the content on the page No. 1
700 Series Professional
UHF Wireless Systems
®
ATW-701 UniPak Transmitter System
ATW-701/G Guitar System
ATW-701/H Headworn Microphone System
ATW-701/H92 Headworn Microphone System
ATW-701/H92-TH Headworn Microphone System
ATW-701/L Lavalier Microphone System
ATW-702 Handheld Dynamic Microphone System
Installation and Operation
Summary of the content on the page No. 2
Professional UHF Wireless Systems Installation and Operation The ATW-R700 receiver features Diversity Reception. Logic This device complies with part 15 of the FCC Rules. circuitry monitors reception, selecting the superior signal from Operation is subject to the condition that this device does two antennas, providing better sound quality and reducing the not cause harmful interference. possibility of interference and dropouts. Soft-touch controls provide convenient access to selection of operat
Summary of the content on the page No. 3
Receiver Installation Antennas Location Extend the permanently attached UHF antennas. The antennas For best operation the receiver should be at least 3 ft. (1 m) are normally positioned in the shape of a “V” (both 45° from above the ground and at least 3 ft. away from a wall or metal vertical) for best reception. Diversity Indicators on the receiver surface to minimize reflections. The transmitter should be at front panel will indicate which antenna is active. least 3 ft. from the receiver, as s
Summary of the content on the page No. 4
Receiver Controls and Functions (Continued) Figure C-Rear Panel Controls and Functions 10. BALANCED AUDIO OUTPUT JACK: XLRM-type connector. A standard 2-conductor shielded cable can be used to connect the receiver output to a balanced microphone-level input on a mixer or integrated amplifier. 11. CORD HOOK: Loop the cord around the cord hook to keep the DC plug from pulling out accidentally. 9 10 11 12 8 12. POWER INPUT JACK: Connect the DC plug from the included in-line AC adapter. 1 8. UNBALAN
Summary of the content on the page No. 5
Transmitter Setup, Controls And Functions Mute Function Power/Mute/Battery Indicator After the battery is installed, press and hold the power button With the transmitter on, a slight touch of the Power/Mute until the battery indicator LED turns green (Fig. F & G). (It will button will toggle between muted and unmuted operation. turn red first; keep holding until it turns green). If the battery Red LED indicates muted operation. Green LED indicates indicator LED does not light up when the power b
Summary of the content on the page No. 6
System Operation (Continued) Setting Levels (Continued) 6. For MIC: While again speaking/singing into the microphone ATW-T702 HandheldTransmitter at typically loud levels, adjust the mixer's input trim control so the highest sound pressure level going into the CAUTION! The small trimmer controls are delicate; use only microphone causes no input overload in the mixer, and yet the supplied screwdriver. Do not force the trimmers beyond permits the mixer's channel and output level controls to their
Summary of the content on the page No. 7
700 Series UHF Operating Frequencies 700 Series Frequency Channel Plan Channel Frequency - MHz TV Channel Each transmitter/receiver system operates on a choice of eight switch-selected frequencies. Available frequencies are shown in 1 542.125 26 the chart. All frequencies may be combined for up to 8 2 545.750 3 551.500 27 simultaneous operating channels. 4 552.000 5 557.875 28 6 559.375 7 560.500 29 8 561.250 † Specifications ® UNIPAK TRANSMITTER OVERALL SYSTEM UHF Operating Frequency 542.125 MH
Summary of the content on the page No. 8
Ten Tips to Obtain the Best Results 1. Use only fresh alkaline batteries. Do not use “general 8. If the AF Level control of the receiver is set too high, it purpose” (carbon-zinc) batteries. may over-drive the input of the mixer or clip the output of the receiver, causing distortion. Conversely, if the receiver 2. Position the receiver so that it has the fewest possible output is set too low, the overall signal-to-noise ratio of obstructions between it and the normal location of the the system m
