Summary of the content on the page No. 1
User Guide
©2007, Shure Incorporated
Printed in U.S.A.
27C3156 (Rev. 4)
Summary of the content on the page No. 2
SHURE INCORPORATED KSM141 DUAL POLAR PATTERN CONDENSER MICROPHONE ® Thank you for selecting the KSM141. Over 75 years of audio experience has contributed to making the KSM141 one of the finest microphones available. If you have any questions not answered in this booklet, please contact Shure Applications Engineering at 847-600-8440, Monday through Friday, from 8:00 am to 4:30 pm, CST. In Europe, call 49-7131-72140. Our web address is www.shure.com. 1
Summary of the content on the page No. 3
Rotating Polar Pattern Switch 0/15/25 dB Attenuation Switch Low Frequency Response Switch FIGURE 1. KSM141 CONDENSER MICROPHONE GENERAL DESCRIPTION ® The Shure KSM141 is an end-addressed condenser microphone with mechanically switching dual polar patterns (cardioid and omnidirectional). Designed for studio use, yet rugged enough for live applications, the KSM141 can withstand extremely high sound pressure levels (SPL). Its low self-noise and extended frequency response make it ideal for reco
Summary of the content on the page No. 4
PERFORMANCE CHARACTERISTICS • Extended frequency response. • Low self-noise. • Exceptional reproduction of low-frequency sounds. • Can withstand high sound pressure levels (SPL). • High output level. • No crossover distortion. • Uniform polar response. • Superior common mode rejection and suppression of RFI (radio frequency interference). MODEL VARIATIONS KSM141/SL KSM141/SL ST PAIR One KSM141 Condenser Microphone Two KSM141 Condenser Microphones One A141C Carrying Case One A141SPC Carrying Cas
Summary of the content on the page No. 5
USING THE KSM141 Mounting the Microphone To secure the KSM141 to a floor stand or boom, thread the mount onto the microphone stand and insert the microphone into the microphone clip. Power Requirements This microphone requires phantom power and performs best with a 48 Vdc supply (IEC-268-15/DIN 45 596). It can operate on voltages as low as 11 Vdc, but headroom and sensitivity will be decreased slightly. NOTE: Most modern mixers provide phantom power. Cable Connections Use a cable with XLR co
Summary of the content on the page No. 6
Setting Low-Frequency Response A three-position switch on the KSM141 lets you adjust the low frequency response of the microphone. The low frequency filters can be used to reduce wind noise, room noise, or proximity effect. Refer to Figure 2. Flat response. This setting +5 provides the most natural sound 0 reproduction in most applicatons. Low-frequency cutoff. This setting provides an 18 dB-per-octave –10 cutoff at 80 Hz. It helps eliminate floor rumble and low-frequency noise produced
Summary of the content on the page No. 7
SPECIFICATIONS Cartridge Type Permanently Biased Condenser Frequency Response 20-20,000 Hz (see Figures 3 and 5) Directional Polar Pattern Cardioid/Omnidirectional (see Figures 4 and 6) Output Impedance 150 Ω (actual) Attenuation Switch 0 dB,15 dB, or 25 dB attenuation Low Frequency Response Switch Flat; -6 db/octave below 115 Hz; -18 dB/octave below 80 Hz Phantom Power 48 Vdc± 4 Vdc (IEC-268-15/DIN 45 596), positive pins 2 and 3 Current Drain 4.65 mA typical at 48 Vdc Common Mode Rejection ≥
Summary of the content on the page No. 8
CARDIOID RESPONSE GRAPHS 15 cm 60 cm FIGURE 3. CARDIOID FREQUENCY RESPONSE 250 Hz 2500 Hz 500 Hz 6400 Hz 1000 Hz 10000 Hz FIGURE 4. CARDIOIDE POLAR PATTERNS 7
Summary of the content on the page No. 9
OMNIDIRECTIONAL RESPONSE GRAPHS 60 cm FIGURE 5. OMNIDIRECTIONAL FREQUENCY RESPONSE 250 2500 500 6400 1K 10K FIGURE 6. OMNIDIRECTIONAL POLAR PATTERNS 20 mm 146 mm FIGURE 7. DIMENSIONS 8
Summary of the content on the page No. 10
CERTIFICATION Eligible to bear CE Marking; Conforms to European EMC directive 89/336/EEC. Meets applicable tests and performance criteria found in European Professional Audio Products EMC Standard EN 55103 (1996); Part 1 (Emissions) and Part 2 (Immunity). The KSM141 is intended for use in environments E1 (residential) and E2 (Light Industrial) as defined in European standard EN 55103. EMC conformance is based on the use of shielded interconnecting cable. FURNISHED ACCESSORIES Case . . . . .
Summary of the content on the page No. 11
Trademark Notices: The circular S logo, the stylized Shure logo, and the word“Shure” are registered trademarks of Shure Incorporated in the United States.“SHOCKSTOPPER” is a trademark of Shure Incorporated in the United States.“Mylar” is a registered trademark of E.I. duPont de Nemours and Company in the United States. These marks may be registered in other jurisdictions. Patent notice: U.S. Patent Des 478068. SHURE Incorporated http://www.shure.com United States, Canada, Latin America, Ca
