Summary of the content on the page No. 1
Dual Receiver VHF Wireless Microphone System
Nady Wireless Systems are type accepted under FCC rules parts 90, 74 and 15. The
device complies with RSS-210 of Industry & Science Canada. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
NADY SYSTEMS, INC.
6701 Shellmound Street • Emeryville, CA 94608 USA
Tel: 510/652-2411 •
Summary of the content on the page No. 2
CONTENTS CONTENTS ...........................................................................................2 INTRODUCTION ....................................................................................3 USING THIS MANUAL ...........................................................................3 SYSTEM FEATURES ................................................................................4 ENCORE DUET RECEIVER .......................................................................5 W
Summary of the content on the page No. 3
INTRODUCTION Thank you for purchasing a Nady Encore DUET dual receiver wireless microphone ENCORE DUET RECEIVER system and congratulations on your choice. The Encore DUET is loaded with top professional operating features and is the best performance and price value available Reception Mode Dual receivers (Channel A and Channel B) in VHF dual receiver wireless systems. Controls Power ON/OFF, dual volume and mute controls (one each, Ch A/B) Connectors Dual balanced XLR and unbalance
Summary of the content on the page No. 4
SPECIFICATIONS SYSTEM FEATURES • Dual channel system for simultaneous operation of two transmitters ENCORE DUET OVERALL SYSTEM PERFORMANCE • Available on 2 selected frequencies in the VHF high band (171-216 MHz) for interference-free, long-range performance Frequency Response 25-20,000 Hz, +/-3dB • Proprietary companding circuitry for an industry-best 120dB Dynamic Range, Dynamic Range 120dB and the clearest, most natural sound available Total Harmonic Distortion < 0.3% • Operating Range:
Summary of the content on the page No. 5
ENCORE DUET RECEIVER 1. Rackmounting the Receiver There are 2 options available for rackmounting the Encore DUET receiver: singly or side-by-side with another Encore Series receiver. a. Single mounting: Remove the receiver SIDE MOUNT CLIP (1) from each side of 38 the receiver (as shown) and slide in the optional ERM-12 RACK EARS (9). b. Side-by-side double mounting: After removing the SIDE MOUNT CLIPS (1) from both Encore receivers, join the two receivers with the EJC-2 JOINING CLIP
Summary of the content on the page No. 6
5. Connecting the Audio Output 4. Microphone Operation The Encore DUET receiver provides both a fixed mic level BALANCED AUDIO OUT- a. Turn on the Link 2 by sliding the ON/STANDBY/OFF SWITCH (41) to the PUT XLR (14) for each channel and an adjustable line level A + B UNBALANCED STANDBY position (transmitter on, audio muted) or the ON position (transmitter AUDIO OUTPUT 1/4" JACK (13) which provides a mixed (summed) Ch A plus Ch B and audio both on). The LOW BATTERY INDICATOR LED (40) will give
Summary of the content on the page No. 7
THE LINK 2™ PLUG-IN TRANSMITTER 16 16 1. Transmitter Set-Up First, slide open the BATTERY COMPARTMENT DOOR (43) to expose compartment. Insert a fresh 9V ALKALINE BATTERY (45), observing polarity. Close the battery compartment door. 2. Handheld Microphone Installation • Step 1 - Rotate the transmitter's threaded LOCKING RING (37) clockwise toward the XLR CONNECTOR (36) until it stops. • Step 2 - Hold your mic in one hand and The Link 2 in the other. 7 • Step 3 - Plug your mic into the XLR
Summary of the content on the page No. 8
WHT HANDHELD MICROPHONE TRANSMITTER 32 35 1. Unscrew the BATTERY COMPARTMENT COVER (17) and remove, exposing the BATTERY HOLDER (18). Insert a fresh 9V ALKALINE BATTERY (19), observing the 34 correct polarity as marked, and screw the cover back on to the microphone. Make sure the cover is screwed on completely. A fresh alkaline battery can last up to 16 33 hours in use, but in order to ensure optimum performance, it is recommended that 32 you replace the battery after every 10 hours of use.
Summary of the content on the page No. 9
WGT INSTRUMENT BODYPACK TRANSMITTER 1. Snap open the BATTERY COMPARTMENT (30) and insert a fresh 9V BATTERY (31), observing the correct polarity. Close the compartment. The WGT is provided with a 3.5 mm LOCKING JACK (32) for connecting the INSTRUMENT CABLE (35). To secure the connection, turn the metal slip ring on the plug clockwise to thread it on to the jack. To unplug, reverse the process. Slip the transmitter into a pocket or clip on to your clothes or instrument strap. (Note: As
Summary of the content on the page No. 10
WLT LAVALIER/LAPEL OR HEADWORN MICROPHONE 24 BODYPACK TRANSMITTER 1. Snap open the BATTERY COMPARTMENT (22) and insert a fresh 9V BATTERY 29 (23), observing the correct polarity. Close the compartment. 28 27 2. The WLT is provided with a 3.5 mm LOCKING JACK (24) for connecting the microphone. Plug in either the LAVALIER/LAPEL (25) or the HEADWORN MICRO- PHONE (26), as supplied. To secure the connection, turn the metal slip ring on the 22 plug clockwise to thread it on to the jack. To unp
