Summary of the content on the page No. 1
MOW’N MACHINE
SWEEPER
FSW6000F
FSW6000T
Tested. Proven. Unbeatable.
MAN0118
Rev. 12/1/2006
OPERATOR'S MANUAL
Summary of the content on the page No. 2
TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration included with the Operator’s Manual. The customer must sign the registration which certifies that all Dealer Check List items have been complete
Summary of the content on the page No. 3
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSIDE FRONT COVER GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear ! sturdy, rough-soled work shoes and protective LEA EL INSTRUCTIVO! equipment for eyes, hair, hands, hearing, and head. Si no lee Ingles, pida ayuda a Make sure attachment is properly secured, alguien que si lo lea para que le adjusted, and in good operating condition. traduzca las medidas de seguridad. Make sure the driveline spring-act
Summary of the content on the page No. 5
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Look down and to the rear and make sure area Do not modify or alter or permit anyone else to is clear before operating in reverse. modify or alter the equipment or any of its compo- nents in any way. Do not operate or transport on steep slopes. Always wear relatively tight and belted clothing Do not stop, start, or change directions sud- to avoid entanglement in moving parts. Wear denly on slopes. sturdy, rough-soled work shoes
Summary of the content on the page No. 6
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! DANGER MODEL NO. SERIAL NO. SHIELD MISSING Woods Equipment Company Oregon, Illinois, U.S.A. 4 - PN 18869 BE CAREFUL! 1 - SERIAL NUMPER PLATE Use a clean, damp cloth to clean safety decals. Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them t
Summary of the content on the page No. 7
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 5 - PN 72803 2 - PN 18864 CAUTION DANGER PINCH POINT AVOID INJURY FROM FRAME PIVOT AND STOPS DKEEPHANDSANDFEETAWAY. ROTATING DRIVELINE 50-0075-1 CONTACT CAN CAUSE DEATH KEEP AWAY! 3 - PN 33347 DO NOT OPERATE WITHOUT - All driveline guards, tractor and equipment shields in place Drivelines securely attached at both e
Summary of the content on the page No. 8
OPERATION REAR TRACTOR WEIGHT Safety is a primary concern in the design and REQUIREMENTS manufacture of our products. Unfortunately, our The sweeper attachment requires additional rear trac- efforts to provide safe equipment can be wiped tor weight as shown in the counterweight chart below. out by an operator’s single careless act. Contact your WOODS dealer for counterweights and In addition to the design and configuration of mount kit appropriate for your specific tractor. equipment, hazard co
Summary of the content on the page No. 9
Operate tractor engine at half throttle when de-thatch- Avoid sudden starts and stops when traveling up and ing grass or sweeping dirt. down hill. Never sweep or back up steep hills. When de-thatching grass, stop tractor, disengage PTO, Move very slowly when turning or operating on slopes turn off key and check for grass wrap around PTO shaft to reduce the possibility of unit tipping or loss of control. and universal shaft every 30 minutes of operation. PRE-OPERATION CHECK LIST Use the gauge whe
Summary of the content on the page No. 10
SERVICE In addition to these lubrication points, lightly oil all roller chains periodically. A CAUTION Check the oil level in gearboxes periodically. Maintain oil level to the bottom of fill plug hole. Use SAE 90W oil. Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear CHAIN ADJUSTMENT sturdy, rough-soled work shoes and protective Check periodically for proper chain tension between equipment for eyes, hair, hands, hearing, and head; gearboxes. If cha
Summary of the content on the page No. 11
ASSEMBLY broom head to mount (1) using bolts provided with DEALER SET-UP INSTRUCTIONS broom head. Assembly of this sweeper is the responsibility of the Attach height adjustment lever (2), and lever guide (18) WOODS dealer. It should be delivered to the owner as shown. Pivot bolt (35) and nut (37) must be snug but completely assembled, lubricated, and adjusted for still allow the lever to rotate. normal cutting conditions. Secure one end of chain (17) to lug on adjustment FIXED ANGLE MOUNT KIT IN
Summary of the content on the page No. 12
20 8--1/4 5 10 TRIM INPUT SHAFT 8 24 DRILL .343 (11/32) DIA 21 HOLES IN SWEEPSTER SHIELD 9 7 23 22 6 24 4 2 22 CD4647A 11 3 1 21. 5/16" NC Flanged hex lock nut 1. Broom mount 7. 2-1/2" Clamp 22. 1/2 NC x 2-1/2 Hex head cap screw 2. 12V Actuator 8. Extension spring 23. 1/2 NC x 3 Hex head cap screw 3. Universal half sheet 9. Upper actuator mount 24. 1/2 NC Hex locknut 4. Universal half sleeve 10. Caster wheel assembly right 5. Power shaft shield 11. Caster wheel assembly left 6. Shield mount stra
Summary of the content on the page No. 13
nector (A) to ease installation. Disconnect the wiring ATTACHING SWEEPER TO TRACTOR harness from the tractor at this point when removing (Figure 4) the broom from the tractor. Rear section of wiring har- Replace existing step on 2-way angle mount of tractor ness may remain on tractor at all times. with shorter step supplied with sweeper. Remove cotter Secure relay and connector to tractor frame using plas- pin on end of step rod and slide out. Install shorter step tic wire ties through holes nea
Summary of the content on the page No. 14
7 PURPLE IGNITION MALE SPADE CONNECTOR 5 MALE SPADE CONNECTOR FEMALE SPADE 7.5 AMP FUSE CONNECTOR BLACK 5WAYFEMALE CONNECTOR TO RELAY. MOUNT RELAY TO SEAT 2 HINGE CENTER MOUNTING BOLT. 4 SWITCH GREEN RED BOX (+) 2 15 AMP FUSE BATTERY 3 GREEN (--) PURPLE WHEN REMOVING 2 WAY MALE CONNECTOR SWEEPSTER FROM WHITE 2 WAY FEMALE TRACTOR, DISCONNECT BLACK CONNECTOR WIRING HARNESS AT THIS POINT 2 WAY FEMALE CONNECTOR PURPLE A TO ACTUATOR MOTOR GREEN WHITE CD4661--var BLACK 2 WAY FEMALE CONNECTOR TO ACTUAT
Summary of the content on the page No. 15
DEALER CHECK LISTS PRE-DELIVERY CHECK LIST DELIVERY CHECK LIST (Dealer Responsibility) (Dealer Responsibility) ___ Inspect the Mow'n Machine and attachments ___ Point out safety features of cutter. Explain the thoroughly after assembly to be certain it is set up importance and meaning of all safety decals and properly before delivering it to the customer. the potential hazards when not followed. ___ The following check lists are a reminder of points ___ Explain to the customer that sweeper attac
Summary of the content on the page No. 16
2-WAY ANGLE SWEEPER ASSEMBLY 57 25 28 32 CD4646A 32 31 58 30 14 51 62 23 29 26 24 27 22 61 3 15 12 13 50 21 52 6 18 17 60 53 8 45 54 20 8 55 9 37 34 4 5 36 48 7 2 56 46 9 63 8 37 4 1 9 47 38 11 33 48 13 38 10 38 3 15 39 8 44 59 9 30 43 10 35 41 17 32 18 40 41 42 16 64 -- DECAL SET MAN0118 (Rev. 12/1/2006) 14 Parts
Summary of the content on the page No. 17
2-WAY ANGLE SWEEPER ASSEMBLY REF PART DESCRIPTION REF PART DESCRIPTION 34 35197 Spring, complete .89 x .12 x 1.0 - 73967 Sweepster® mounting kit 35 72403 Pin, bent .5 x 1.96 - 71965 Sweepster® broom head 36 1972 * Grease fitting 1 72737 Broom main mount 37 70086 3/8 Spacer 2 72118 Broom mount pivot 38 70004 3/4 Spacer 3 72119 12V Actuator 39 72761 Gauge wheel fork 4 70767 Gearbox 40 31745 Semi-pneumatic wheel 5 72120 Sprocket 50B20 41 31345 .75 x 1.38 Bearing 6 72121 Sprocket 50B11 42 29368 1/2
Summary of the content on the page No. 18
FIXED ANGLE SWEEPER MOUNT KIT ASSEMBLY 6--1/2 41 -- DECAL SET TRIM INPUT SHAFT 31 17 16 3 15 4 36 32 19 10 2 30 33 40 7 6 CD4649A 18 39 34 5 35 20 14 37 38 13 ® SEE SWEEPSTER MANUAL 10 ® 8 1 FOR SWEEPSTER PARTS. 11 REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 19 70931 1 Shield mount bracket - 73959 - Fixed angle mount kit (includes 1-40) 20 4115* 2 3/16 x 1-1/8 Spring pin - 71965 - Sweepster® bruck head 60" 30 3597* 1 1/8 x 1 Cotter pin 1 72778 1 Fixed angle sweeper mount 31 71206* 4 .25-20
Summary of the content on the page No. 19
2-WAY ANGLE SWEEPER WIRE DIAGRAM 7 PURPLE IGNITION MALE SPADE CONNECTOR 5 MALE SPADE CONNECTOR FEMALE SPADE 7.5 AMP FUSE CONNECTOR BLACK 5WAYFEMALE CONNECTOR TO RELAY. MOUNT RELAY TO SEAT 2 HINGE CENTER MOUNTING BOLT. 4 SWITCH GREEN RED BOX (+) 2 15 AMP FUSE BATTERY 3 GREEN (--) PURPLE WHEN REMOVING 2 WAY MALE CONNECTOR SWEEPSTER FROM WHITE 2 WAY FEMALE TRACTOR, DISCONNECT BLACK CONNECTOR WIRING HARNESS AT THIS POINT 2 WAY FEMALE CONNECTOR PURPLE A TO ACTUATOR MOTOR GREEN WHITE CD4661--var BLACK
Summary of the content on the page No. 20
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware define
