Summary of the content on the page No. 1
SWEEPER
ASSEMBLIES
NH TS100-135A
Current as of 6/11/07
PARTS LISTING WITH
MOUNTING AND OPERATING
INSTRUCTIONS
Tiger Corporation
3301 N. Louise Ave.
Sioux Falls, SD 57107
1-800-843-6849
1-605-336-7900
www.tiger-mowers.com
06020012
PAGE - 1
Summary of the content on the page No. 2
FORWARD This manual contains information about the many features of the Tiger THS Sweeper operator safety instructions, maintenance, and operating techniques. This manual will also assist you in the proper break-in daily care, and troublleshooting of your new sweeper. We recommend that you read carefully the entire manual before operating the unit. Also, time spent in becoming fully acquainted with ites performance features, adjustments, and maintenance schedules will be repaid in a long and s
Summary of the content on the page No. 3
SAFETY PRECAUTIONS This symbol means: CAUTION ! Your safety is at rick ! – Any R.O.P.S. (roll over protective structure) should not be drilled, welded on, or altered in any manner. Any alteration may reduce your protection. – Do not bypass the tractor neutral safety swith. Jumping or bypassing can cause tractor runaway. – Do not allow any persons on the equipment except the operator. – Loose clothing that can catch in moving parts should be avoided. – Use the hand holds and step-plate
Summary of the content on the page No. 4
This symbol means: CAUTION ! Your safety is at rick ! – Reduce speed when turning, taking curves, rough ground, or hillsides to reduce chance of rollover. – Always keep tractor in gear when traveling downhill to prevent runaway. – When driving on a road, day or night, use lighting and markings required by local laws. – Lower equipment when not in use. – Whenever stopping or leaving the unit you should: stop tractor and equipment, lower equipment, be sure all motion stops, and remove
Summary of the content on the page No. 5
OPERATION Be sure the ball valves on the mower hydraulic tank are OPEN before starting the tractor. Serious damage to the hydraulic system can occur if the valves are not OPEN. For brush operation: open the high pressure valve located near the pressure port of the pump and close the high pressure valve located near the electrical solenoid. This procedure shuts off the oil flow to the mower. For mower operation: close the high pressure valve located near the pressure port of the pump and ope
Summary of the content on the page No. 6
It is very possible to cut brush life by 50% if the frame is not level. Running an unlevel brush is jast like throwingmoney out the window. The small amount of time spent leveling a brush before sweeping is paed back many times over in longer brush life. As a general rule brush level should be checked every day before operating. Uneven brush wear can also be caused by discharging material to the same side of the brush all the time. Flipping the brush core end - for - end a couple of times dur
Summary of the content on the page No. 7
TIGER SWEEPER MODELS THS - 72CC & THS - 96C IMPORTANT INSTRUCTIONS 1. Do not store sweeper polypropylene brushes in direct sunlight! Direct sunlight will cause the bristles to deteriorate, causing the bristles to become brittle. If the broom is to be stored for any length of time, store it in the shade, inside, or cover the brush with a tarp to protect it from the sun. 2. Do not stor the sweeper power broom with the weight on the bristles! Storing the sweeper power broom
Summary of the content on the page No. 8
MOUNTING INSTRUCTIONS Please rea and understand the instructions and schematics completely before beginning assembly. Parts and drawings may vary slightly due to the variety of tractor makes and models. The mounting kit you receive should be correct for your application. If questions arise please contact your local dealer or Tiger Service as needed. Lay out all loose parts on a clean surface for easy identification. Part numbers and descriptions can be found in this manual and other informatio
Summary of the content on the page No. 9
11. The spring - chain assemblies are used to help support the weight of the brush head assembly when in the sweeping position. Hook on spring to each of the outside holes in the top plate of the brushhead upright. The chains are con nected to the outside slots in the chain holder on the spring - chain assembly. The spring - chain assemblies will require adjustment after installation is complete. 12. Connect a 1/4” hydraulic hose from the lift cylinder to
Summary of the content on the page No. 10
LEVELING INSTRUCTIONS The sweeper must be leveled t maintain even brush wear and to produce efficient sweeping action. If the broom is not leveled at first and periodically after that, then it will put stress on certain parts causing excessive wear. The broom is easily leveled if these steps are followed. 1. Drive the assembled broom onto a level paved area. Swing the brush head assembly to the straight position. Lower the brush into the sweeping position with the weitght of the b
Summary of the content on the page No. 11
LEVELING INSTRUCTIONS CONTINUED Make a note of the measurements. Swing the brush head assembly to the left and take the same measurements. If the measurements are not equal, refer to previous leveling steps and illustrations for adjustments. 5. After leveling, tighten the brush head mounting bolts E, F and G PAGE - 11
Summary of the content on the page No. 12
SUPPORT YOKE ADJUSTMENT NOTE: This section applies only to units with serial number 75146 and above. Units with serial number below 75146 do not have adjustable support yokes. Before operating the sweeper the brush head frame support yokes should be checked and if necessary adjusted as follows: 1. Loosen the two 5/8” carriage bolts in each of the support yokes as shown in the figure below. 2. Swing the brush head assembly fully to the right. 3. Snug the right support yoke around the b
Summary of the content on the page No. 13
BRUSH REPLACEMENT 1. Disconnect the two hydraulic hoses at both motors. IMPORTANT: Tape over the ends of the hydraulic hoses and the hydraulic motor ports to prevent contamination of the hydraulic system. 2. Remove the four bolts holding the hood in place. Lift the hood off the brush and set aside. 3. Remove the two carriage bolts in the motor housing at both ends of the brush head assembly. 4. Slide the brush assembly out of the brush head frame. 5. Place a coupl
Summary of the content on the page No. 14
MOTOR AND HUB REPLACEMENT 1. Disconnect the two hydraulic hoses at both motors. IMPORTANT: Tape over the ends of the hydraulic hoses and the hydraulic motor ports to prevent contamination of the hydraulic system. 2. Remove the four bolts holding the hood in place. Lift the hood off the brush and set aside. 3. Remove the two carriage bolts in the motor housing at both ends of the brush head assembly. 4. Slide the brush assembly out of the brush head frame. 5. Remove th
Summary of the content on the page No. 15
PAGE - 15
Summary of the content on the page No. 16
TRACTOR MOUNT - MAIN FRAME PAGE - 16
Summary of the content on the page No. 17
TRACTOR MOUNT - MAIN FRAME ITEM PART NO. QTY. DESCRIPTION 1 34857 1 MTG,THS 2 06410443 1 MNT,LH,SWPR,CNH,TSA 2 06410442 1 MNT,RH,SWPR,CNH,TSA 4 06430049 4 SPACER,2.00x1.00x3.34 5 41644 1 PLATE,ATTACHING 6 21735 4 CAPSCREW,1/2 x 2 1/2,NC 7 24879 4 CAPSCREW , 20MM x 65MM(2.5 PITCH) 8 21843 4 CAPSCREW 3/4” x 6” NC 9 33880 4 FLATWASHER, 3/4”,GR 8, SAE 10 06400165 4 SPACER,COOLER,FRONT PAGE - 17
Summary of the content on the page No. 18
PAGE - 18
Summary of the content on the page No. 19
PAGE - 19
Summary of the content on the page No. 20
PAGE - 20
