Summary of the content on the page No. 1
swisherinc.com
OWNER’S
MANUAL
MODEL NO.
T11544
START SERIAL # L205-006001
ENDING SERIAL #: L205-031000
T11044
START SERIAL # L205-045001
ENDING SERIAL #: L205-031000
44” FINISH CUT
T10544BSPB
START SERIAL # L205-021001
ENDING SERIAL #: L205-031000
TRAILMOWER
T12544
START SERIAL # L205-024001
ENDING SERIAL #: L205-031000
T1144HSP
START SERIAL # L205-046001
ENDING SERIAL #: L205-031000
IMPORTANT
Assembly
Read and follow all Safety
Precautions and
Operation
Instructions before
operating th
Summary of the content on the page No. 2
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This warranty is subject to the following limitations and exclusions: 1) Engine Warranty all engines utilized on our products has a separate warrant
Summary of the content on the page No. 3
SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. Read this manual completely. This machine can amputate hands, feet, and throw objects. Failure to observe the following safety instructions could result in serious injury or death. • Read the manual. Learn to operate this machine safely. • Always disconnect the spark plug wire and pla
Summary of the content on the page No. 4
• Turn off the blades when not mowing. Before leaving the machine, turn off the blades and stop the engine. • Watch for traffic when operating near or crossing roadways. • Do not operate the mower if it has been dropped or damaged in any manner or if the mower vibrates excessively. Excessive vibration is an indication of damage. Repair mower as necessary. • Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear only solid shoes with good traction when mowin
Summary of the content on the page No. 5
SAFETY DECALS Replace decal immediately if damaged. Order by part number from Swisher Mower and Machine Co. Inc. OD33-Speed Decal TrailMower Serial # OD55-Triangle Danger Decal (All four deck corners) OD99127-44" Deck White Decal (Not Pictured) OD99127-44" Deck White Decal (Not Pictured) Engine Serial # OD15-Void Warranty Decal OD36-Deflector Decal OD11-No Step Decal OD99125-Medium Swisher Logo White Decal (Not Pictured) OD29-Danger Decal OD103-Single Point Height Adjust Decal OD45-Warning D
Summary of the content on the page No. 6
OPERATING YOUR TRAILMOWER The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before staring any cutting machine and while operating such a machine. The operation of any cutter produces sound waves that are damaging to the human ear. Ear protection is recommended. CAUTION! Tragic accidents can occur if the operator is not alert to the presence of
Summary of the content on the page No. 7
ENGAGING BLADES (without T-handle option, Standard) The TrailMower will not start if the blade lever is in the “ENGAGED” position. • Engage blades by rotating blade lever into the “ENGAGED” position. • Rotate blade lever in opposite direction to disengage blade. • The dual braking system is applied when the blades become disengaged. It is designed to bring the blades to quick stop (approximately 7 seconds). Each TrailMower brake system has been tested and calibrated. For safety, the consum
Summary of the content on the page No. 8
MOWER HEIGHT ADJUSTMENT • Make adjustments while TrailMower is not running. • There is approximately 1 ½” to 4 ½” of height adjustment. • Rotate height adjust crank handle(s) in a clockwise direction to lift the mower deck. A counter-clockwise direction is used to lower the mower deck. • For best results, see “SUGGESTED PRACTICE” section. Graduated scales are for reference only, not the actual cutter height. FRONT TO BACK ADJUSTMENT For best cutting results, the mowing deck should be raised t
Summary of the content on the page No. 9
SUGGESTED MOWING PRACTICES • Operate mower engine at full throttle to assure the best cutting performance and maximum material discharge. • Allow wet grass to dry. Wet grass will clump and collect under the mowing deck. • Mowing should be started with tow vehicle in low gear and increased only as safe mowing conditions permit. Mowing speed should not exceed 5 MPH. • The average lawn should be cut to approximately 2.5” during the cool season and to over 3” during the hot months. • For a heal
Summary of the content on the page No. 10
MOWER MAINTENANCE GENERAL RECOMMENDATIONS The warranty on this TrailMower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual. Some adjustments will need to be made periodically to maintain your unit properly. All adjustments in this manual should be checked at least once each season. BEFORE EACH USE • Check engine oil level on a level surface. (Check twice to insure a
Summary of the content on the page No. 11
BLADE CARE AND SERVICE For best results cutter blades must be kept sharp. The blades can be sharpened with a few strokes of a file or grinding wheel. Do not attempt to sharpen blades while they are on the cutter. Disconnect spark plug wire before servicing unit. Important: Replace blades that have been damaged or deeply nicked. Important: Check blade and spindle hardware on a regular basis to make sure nuts are tight. Only a qualified mechanic should make any adjustments, di
Summary of the content on the page No. 12
BALL LOCK PINS FRONT LEFT RIGHT Left offset shown REAR FIGURE ONE Slide plastic tube snug against toggle switch. FIGURE TWO (FIGURE FIVE FOR DETAILS) 12
Summary of the content on the page No. 13
T44 RECOIL START T44 12 VOLT START FIGURE THREE WIRING CONFIGURATIONS PARTS NOT SHOWN WIRING HARNESSES B&S ENGINE (Remote Start only) WH44CHB12V HONDA ENGINE WH1144H REMOTE OPTION WH44RCH PULL START W/ B&S ENGINE 10638 TOGGLE/GROUND WIRE ASSEMBLY 9090 BLADE ENGAGE CABLE 9074 12V B&S MANUAL BLADE ENGAGE 10235 12 VOLT MODELS BATTERY (12N12A) RECOMMENDED SOLD SEPARATELY SOLENOID 9043 BATTERY CABLE - POSITIVE BCSR BATTERY CABLE - NEGATIVE BCS EXTRAS VELC
Summary of the content on the page No. 14
1 SEE DETAILS 2 4 8 15 1 14 3 4A 16 5 6 5A 7 17 9 7A 10 18 13 13, 23 28 19 11 22 12 20 29 23 21 23 27 144 30 37 145 23 32 140, 141, 142 33 24 38 143 25 39 23 31 26 23A 34 35 36 FIGURE FOUR T-HANDLE OPTION SEE DETAIL SINGLE POINT HEIGHT ADJUST ITEM # DESCRIPTION PART # ITEM # DESCRIPTION PART # 1 BELT COVER 10599* 23 5/16 NUT NB170 2 MOTOR BASE 4517* 23A 5/16 BOLT NB596 3 1/4 BOLT NB114 24 3/8 NUT NB182 4 HEIGHT ADJUSTER 25 ANTI-SCALP ROLLER 3/8" AS001 KNOB H7K 26 3/8 BOLT NB575 5/16 PAL NUT NB2
Summary of the content on the page No. 15
FIGURE SIX 52 BLADE SET-UP 53 40 55 54 43 44 57 56 41 58 45 46 65A 55 42 60 61 48 47 49 50 59 51 64 63 62 FIGURE FIVE ITEM # DESCRIPTION PART # ENGINE SET-UP 52 3/4 NUT NB175 ITEM # DESCRIPTION PART # 53 UPPER BELLEVILLE AS155 40 ENGINE NOT AVAILABLE 54 BLADE PULLEY B4104 41 5/16 BOLT NB253 55 THIN WASHER NB179 42 5/16 NUT NB170 56 BLADE DRIVER 9018 43 TOGGLE BRACKET 4483Z BEARING B98 44 SAFETY TETHER 6736 4.25" SHAFT 9076 45 TOGGLE SWITCH 685SP BEARING HOUSING B99ECTK 46 UPPER ENG. SPACER BB105
Summary of the content on the page No. 16
65 79 73 67 81 74 78 71 72 76 69 68 80 SEE FIG. 86 70 NINE 66 87 89A 88 84 85 82 75 77 FIGURE SEVEN 75B 84 T-HANDLE OPTION 83 FIGURE EIGHT ITEM # DESCRIPTION PART # STANDARD ENGAGE 65 T-HANDLE LEVER 4463TK 66 COTTER PIN NB597 ITEM # DESCRIPTION PART # 67 1/4 NUT NB180 77 ENGAGE STANDOFF 4547TK 68 WASHER NB274 78 5/16 Spade Bolt NB260 69 ENGAGE LINK 4461TK 79 1/2 BOLT NB155 70 CABLE CLEVIS 9023MOD 80 ENGAGE LEVER 4548TK 71 5/16 NUT NB181 81 HANDLE KNOB B19BLACK 72 CLEVIS PIN NB518 82 1/4 NUT NB5
Summary of the content on the page No. 17
ITEM # DESCRIPTION PART # 89 106A 89 3/8 NUT NB280 90 92 90 WASHER NB272 91 91 IDLER PULLEY B527 94 92 WASHER NB556 96 93 5/16 SERR FLG BOLT NB253 94 IDLER SPRING 4422 95 95 5/16 NUT NB170 106 96 BRAKE LINK 4532 105 104 97 3/8 BOLT NB107 97 98 5/16 SPADE BOLT NB260 102 99 EYE BOLT V139EB 103 99 99A 5/16-18 NUT NB210Z 93 100 3/8 NUT NB182 96 101 IDLER BUSHING 6037 101 102 IDLER BRACKET 4530 98 100 103 1/4 NUT NB524 104 1/4 BOLT NB218 105 IDLER SPACER 6040 99A FIGURE NINE 106 3/8 BOLT NB618 Tensio
Summary of the content on the page No. 18
FIGURE ELEVEN BRAKE ARM CONFIGURATIONS Item # Description Part # 118 1/4-20 BOLT NB162 119 1/4-20 NUT NB524 120 BRAKE ARM 10589 121 1/4-20 NYLOCK NB180 122 BRAKE PAD 9039 123 10-24 BOLT NB710 124 10-24 KEP NUT NB172 125 EYE BOLT V139EB 128 1/4-20 NUT NB180 129 1/4-20 BOLT NB102 148 1/4-20 x 2 BOLT NB218 18
Summary of the content on the page No. 19
19
Summary of the content on the page No. 20
44” FINISH CUT TRAILMOWER OWNER’S MANUAL HOW TO ORDER REPAIR PARTS: Each TrailMower has its own serial number. Each engine has its own serial number. The serial number for the TrailMower MODEL NO. will be found on the right hand side of the drive belt housing. The serial number for the engine will be found on the top of the blower fan housing. All TrailMower parts listed herein may be ordered directly T11544 from Swisher Mower & Machine Co. Inc., your nearest Swisher dealer, or from our
