Summary of the content on the page No. 1
INSTALLATION AND OPERATION INSTRUCTIONS
DIRECT DRAW DISPENSER - SELF-CONTAINED MODELS
MODEL NOS.
DS Series
IMPORTANT INFORMATION Table of Contents
Fill out the enclosed warranty card and mail to the
PREPARING THE CABINET FOR USE
Perlick Corporation to register the warranty. If the
Specifications.........................................................2
card is not returned, the warranty period will begin
List of Included Parts.............................................3
from the date the equip
Summary of the content on the page No. 2
Installation and Operating Instructions Sizes and Specifications, Direct Draw Dispensers - Self-Contained DOOR FINISH MODEL NUMBERS BLACK DS60B DS72B DS84B STAINLESS STEEL DS60S DS72S DS84S SPECIFICATIONS KEG CAPACITY 2 Keg 3 Keg 4 Keg NUMBER OF DOORS 2 2 3 CABINET Length Ins. (mm) 60” (1524) 72” (1829) 84” (2134) 3 3 3 DIMENSIONS Depth Ins. (mm) 24 /4” (629) 24 /4” (629) 24 /4” (629) 1 1 1 Height Ins. (mm) 34 /2” (876) 34 /2” (876) 34 /2” (876) NO. OF DISPENSING HEADS 1 1 2 NO. FAUCETS 2 2 2 1
Summary of the content on the page No. 3
Preparing the Cabinet for Use – Direct Draw Dispensers Self-Contained Apply RTV around the base of the dispensing Parts List head to seal it to the top. Align the dispensing Faucet Standard. head over the holes on the cabinet top and use Faucet Head Assembly. screws provided to secure standard to cabinet 3 Black Connector Hose ⁄16” x 3’. top. Wipe off excess RTV to complete the seal. 5 ⁄16” Air Hose. Attach faucet to standard using spanner Spanner Wrench. wrench to tighten cou
Summary of the content on the page No. 4
Installation and Tapping – Direct Draw Dispensers Self-Contained Connecting the Keg Coupler Tapping a Single Valve Keg (Sankey): (when Supplied by Perlick) Place one brown leather washer into black beer line connector hose on hex nut side. Screw connector to stainless steel beverage line on Step 1 faucet standard. Tighten with a wrench, but do Single Valve Keg Coupler not over tighten. Make sure lever handle on the keg coupler is in the UP (untapped) position. Place one brown leather
Summary of the content on the page No. 5
Installation and Tapping – Direct Draw Dispensers Self-Contained Connecting the Regulator to the Replacing CO2 Gas Cylinder CO2 Cylinder Turn CO2 hand valve clockwise until seated and Remove blue plug from regulator fitting. close shut-off valve on regulator. (Note: Do not remove the carbonic washer). Unscrew regulator from cylinder fitting. Screw regulator onto gas cylinder valve. Tighten Replace carbonic washer (Part No. 157F2P), with wrench until vertically straight. Be sure that
Summary of the content on the page No. 6
Draft Beer Information – Direct Draw Dispensers Self-Contained Temperature One of the most common causes of dispensing At temperatures lower than 30° F., beer will freeze. When beer freezes, the alcohol in the beer may problems is improper temperature. Draft beer separate and cause the beer to be cloudy with an should be stored at a temperature between 32° and 38°. At warmer temperatures, beer will foam. “off” taste. Refrigeration and Temperature Control Adjusting the temperature The Direct Dra
Summary of the content on the page No. 7
Cleaning the Beer System – Direct Draw Dispensers Self-Contained The entire beer system, to include the faucet, flexible Beer Stone: beer line and tapping devices must be cleaned at All beer contains calcium which is present from regular intervals. We recommend flushing the entire the grains used in the brewing process. it is an system with fresh water immediately after a keg has important natural material in draft systems in been emptied. Once each month the system should that as it oxidi
Summary of the content on the page No. 8
Pouring a Perfect Glass of Beer – Direct Draw Dispensers ➠ STEP 1 Start with a clean glass. Place the glass at a 45° angle, one inch below faucet. Do not let the glass touch the faucet. Open the faucet all the way. STEP 2 ➠ After the glass has reached half full, gradually bring the glass to the upright position ➠ STEP 3 Let the remaining beer run straight down the middle of the glass. This ensures proper release of CO2 by 3 producing a ⁄4” to 1” foam head. STEP 4 ➠ Close the faucet quickly an
Summary of the content on the page No. 9
Trouble Shooting – Direct Draw Dispensers Self-Contained Beer Service Problems Cloudy Beer: Beer in glass appears hazy, not clear. Wild Beer: CAUSES: Dispensed beer has either too much foam or Dirty glass. is all foam. Dirty faucet or beer line. CAUSES: Frozen or nearly frozen beer. Beer has been dispensed improperly. Old beer. Solution: See pouring instructions Beer that has not been refrigerated for a on page 8. long period of time. Regulator pressure is set too high. War
Summary of the content on the page No. 10
Replacement Parts – Direct Draw Dispensers Self-Contained MODEL NOS. DS60B DS72B DS84B DS60S DS72S DS84S Condensing Units Condensing unit 115 volt, 60 hz. C22647 C22646 C22646 Condensing unit 515301063 515301062 515301062 Compressor 513200314 513200003 513200003 Fan motor assembly 215315009 215315009 215315009 Condenser coil 15352019 15352019 15352019 Terminal board 219101538 219101538 219101538 Overload protector MRT20AGK5590 MRT22AGK5590 MRT22AGK5590 Relay 21351619 21351619 21351619 Capacitor
Summary of the content on the page No. 11
Replacement Parts – Direct Draw Dispensers Self-Contained For Single Valve Keg Coupler (Series D) 14 4 Item Part 3 No. No. Description 1 .............32499................Probe assembly 1 2 ............F40184...............Probe body 2 3...........31080-2P.............Ball 4............43641-1 ..............Ball retainer 5...........31087-2P.............Probe washer 15 6 .............31089................“O” Ring - 3-per assembly 13 6 7 .............43061................Body 8...........23682-2
Summary of the content on the page No. 12
Wiring Diagram – Direct Draw Dispensers Self-Contained CAPPED DS Series 2, 3 and 4 Keg Coolers NOT USED EVAPORATOR FAN EVAPORATOR FAN BLACK WHITE THERMOSTAT BLACK POWER CONNECTION CONDENSING UNIT BLACK WHITE GREEN JUNCTION BOX 8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069 Toll Free 800-558-5592 • E-Mail: Perlick@Perlick.com • www.Perlick.com Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications
