Summary of the content on the page No. 1
Installation
41
Up Down On/Off SuperFrost Alarm
64
On/Off Light Zone Up Down
0
Instructions
For wine cooler with
NoFrost freezer compartment and
Side-By-Side Units
with IceMaker
Instructions
de montage
Armoire de mise en température des
vins avec congélateur NoFrost et les
appareils côte à côte
2-6
4-8
avec IceMaker
6-12
4
2-6
Instrucciones
4-8
6-12
3
de instalación
2-6
4-8
Armario de acondicionamiento de
6 -12
2
vinos con congelador NoFrost y
unidades lado a lado
2-6
4-8
6-12
con IceMak
Summary of the content on the page No. 2
IMPORTANT PLEASE READ AND FOLLOW THESE INSTRUCTIONS These instructions contain Warning and Caution statements. This information is important for safe and efficient installation. Always read and follow all Warning and Caution statements! WARNING ! States a hazard that may cause serious injury or death if precautions are not followed. CAUTION ! Signals a situation where minor injury of product damage may occur if you do not follow instructions. IMPORTANT This highlights information that is
Summary of the content on the page No. 3
IMPORTANT TO THE INSTALLER It is very important that the guidelines and instructions are followed in the manual to ensure proper installation and operation of the unit. The Installation Guidelines section contains important information for making sure the installation is correct. Read and understand all the information in Installation Guidelines, and in this manual before the unit is installed. A delight in freshness WF1051 / EWTNes 2956 1
Summary of the content on the page No. 4
TABLE OF CONTENTS Contents Page Installation Guidelines ................................................................................. 3 Area Requirements ............................................................................... 3 Electrical Requirement .......................................................................... 3 Customer’s Responsibility .................................................................... 3 Blocking For Safety .......................................
Summary of the content on the page No. 5
INSTALLATION GUIDELINES Area Requirements WARNING ! Verify the following: ELECTROCUTION HAZARD Floors can support refrigerator’s weight plus Electrical Grounding Required. This approximately 1200 pounds (544 kg) of food appliance is equipped with a three-prong weight. (grounding) polarized plug for your protection against possible shock hazards. Finished kitchen floor height has to be level. DO NOT remove the round grounding Appliance must be shimmed to the floor level if prong
Summary of the content on the page No. 6
PLANNING INFORMATION Cabinet Opening Dimensions - Figure 1 Allow units to open a minimum of 90° to prevent problems removing drawers. With the door opening 90°, you may have to move drawers slightly to clear the door interior. Refer to the minimum door clearances in the Pre- Installation Specifications chart. Allow for a minimum 3-3/4" (95 mm) filler, for corner installations, so the door can open to 90°. If you’re using raised panels, consider using a wider filler. IMPORTANT Refer to
Summary of the content on the page No. 7
PLANNING INFORMATION WF1051 - Figure 2 Figure 2 A delight in freshness WF1051 / EWTNes 2956 5
Summary of the content on the page No. 8
PLANNING INFORMATION Side-By-Side WF1051 and RB1400 - Figure 3 Figure 3 A delight in freshness WF1051 / EWTNes 2956 6
Summary of the content on the page No. 9
PLANNING INFORMATION The factory setting for the door to swing open is 130°. Use this illustration to ensure other cabinets or counters do not interfere with the door opening. 130° A delight in freshness WF1051 / EWTNes 2956 7
Summary of the content on the page No. 10
PLANNING INFORMATION The optional setting for the door to swing open is 90°. Use this illustration to ensure other cabinets or counters do not interfere with the door opening. 90° A delight in freshness WF1051 / EWTNes 2956 8
Summary of the content on the page No. 11
REVERSING DOOR HINGES The door hinges can be changed from one side to the other if required. 5 1. Figure 4: Top: Unscrew the 2 5. hinge pin (2) and remove the 14 screw (5). 1. 2. Swivel out the door at the X top, ensuring that you do not Y lose the stop (7) and bushing 2. 8 (8); lift off the door and place 2. 7 it on the floor. Unscrew the handle from the upper door A and pull out the cover caps (A). Then screw 3. the handle on the opposite side of the 9 upper door and place the plugs
Summary of the content on the page No. 12
REVERSING DOOR HINGES 6. Figure 5: Unscrew the lower hinge (13). 8. Unscrew the center hinge (10) and cover (11), - Remove the washer, stops and bushing (14, 7, 8). pull them off to the side and after turning them - Remove screw (Q). through 180°, slide them on again on the - Transfer hinge pin (2) to the opposite side. opposite side and secure them. - Transfer screw (Q) to the opposite side. - Turn the stop (7) through 180° and position 9. Place the lower door on the hinge pin (2) at t
Summary of the content on the page No. 13
REVERSING DOOR HINGES 10. Figure 6: Lift up cover (3) on handle side, push 12. Transfer hinge pin and screw to the respective outward; lift up cover (1) on hinge side and pull opposite side of the hinge (4), but do not insert off. them in the hole or fasten them now. 11. Unscrew mounting plate (21): first mounting 13. On the upper door, install the door fittings as screw (20), then inner retaining screw (25). shown in Figure 6. Insert the plugs (X) as - Unscrew hinge (4): first remove the m
Summary of the content on the page No. 14
REVERSING DOOR HINGES Door Opening Angle - Figures 7, 8 The appliance is delivered with a door opening angle of 130°. If the angle is to be decreased to 90°, proceed as follows: Insert attached screw (6) in the upper hinge as shown in Figure 7. Insert eccentric (Z) in the lower hinge as shown in Figure 8. Fix the eccentric with screw (V). The eccentric pin must point away from the hinge pin. 6 Fig.D1-2 BGENes Figure 7 Q Z V Fig.D1-2 BGENes Figure 8 A delight in freshness WF1051 / EWTNe
Summary of the content on the page No. 15
INSTALLATION Only install the winecooler/freezer in a stable 1. 2 1 kitchen cabinet that has been properly aligned. - Mount and fix the handles, depending on your model and choice. Unpacking Unpack the installation kit and check with the pro- 3 vided parts list if all parts are included. 2. The part numbers given in the parts list are identical 4 to the numbers in the respective fi gures. 6 4 For installation you will need the following tools: 5 5 3. 6 4 5 Included: 8 - Star Key Torx® 15 - St
Summary of the content on the page No. 16
INSTALLATION - Figure 17: Connect the appliance to the 1. Carefully slide the appliance into the cabinet main power supply. until the ventilation grille touches the surrounding - If the appliance is equipped with an kitchen cabinet. IceMaker, establish the connection for the water supply. See “IceMaker, Water 2. Align the appliance until it is parallel with the sur- Connection”. rounding kitchen cabinet. Use the open- end wrench 10 mm (3) to adjust the feet at the front. 1. 2. 1 2 2 3
Summary of the content on the page No. 17
1 1/2” (38mm) INSTALLATION The following ventilation cross-section and 2 At least 31 square inches (200cm ) distances must be observed: - There must be a ventilation space of at least 31 square inches (200 cm²) per appliance in the cabinet plinth and under the cabinet top panel. - The depth of the ventilation duct at the rear of the cabinet must be at least 1- 1. 1/2" (38 mm). Alternatively: 1. For built-in appliances without ventilation grilles and only with an 2 installation fram
Summary of the content on the page No. 18
min 3" BLOCKING FOR SAFETY IMPORTANT Figure 21: Secure the appliance in place so it does The anti-tip brackets can be installed in either not tip forward when the fully stocked door is direction or closer together. Always position opened. the anti-tip brackets as wide apart as possible, 1. Measure the distance from the floor to the but make sure they are anchored to two studs. upper edge of the unit. 5. Using the adjustable roller base, raise the unit 2. Locate and mark two wall studs (1
Summary of the content on the page No. 19
ICEMAKER Water Connection - Figure 22 Please read the first three points of the safety instructions and warnings before connecting the appliance to the main water supply. The water pressure must be between 21.8- 87.0 psi (1.5-6 bar). Use a 1/4" OD copper line to connect the water supply to the solenoid valve. Allow extra length to the water supply line to provide slack for easy removal and to prevent the line from kinking. This is not supplied with the appliance (Figure 22). A shut-o
Summary of the content on the page No. 20
ICEMAKER Connection to the Water Supply - Figures 23, 24 1. Install the shut-off valve, water filter and 3. Open the shut-off valve for the water supply automatic shut-off device as required. and check the entire water system for leaks. Before the appliance is used for the first time Note a licensed plumber should bleed air from the The solenoid valve is located at the rear of system. your unit. 4. Insert the electrical plug for the combined 2. Place a 1/4" OD copper tubing between the
