Summary of the content on the page No. 13
LUBRICATION & MAINTENANCE BREAK-IN K%
8 HOURS (DAILY) + % E : )&4L7C
D '
34C&
D 40 HOURS (WEEKLY) 0 #
C0
D 100 HOURS (BIWEEKLY) 3 L7C3
D COMMENTS PROCEDURE
Summary of the content on the page No. 14
TROUBLESHOOTING CUTTING CONDITIONS CAUSE CURE CONDITION Stringers - Occasional Low engine RPM Run engine at full 3600 RPM Blades of Uncut Grass Ground speed too fast Slow speed to adjust for conditions Wet grass Cut grass after it has dried out Dull blades, incorrect sharpening Sharpen blades Deck plugged, grass accumulation Clean underside of deck Width of Deck Belts slipping Adjust belt tensions SGB020 Streaking - Strips of Dull, worn blades Sharpen blades Uncut Grass in Cutting Path Incorrect
Summary of the content on the page No. 15
TROUBLESHOOTING CUTTING CONDITIONS CAUSE CURE CONDITION Uneven Cut on Flat Lift worn off of blade Replace blade Ground - Wavy High-Low Blade upside down Mount with cutting edge toward Appearance, ground Scalloped Cut, or Rough Contour Deck plugged, grass accumulation Clean underside of deck Too much blade angle (deck pitch) Adjust pitch and level Deck mounted improperly See your authorized SCAG dealer Bent spindle area See your authorized SCAG dealer Dull blade Sharpen blade Width of Deck SGB020
Summary of the content on the page No. 16
TROUBLESHOOTING CUTTING CONDITIONS CAUSE CURE CONDITION Scalping - Blades Low tire pressures Check and adjust pressures Hitting Dirt or Cutting Very Close to Ground speed too fast Slow speed to adjust for conditions the Ground Cutting too low May need to reduce ground speed, raise cutting height, change direction of cut, and/or change pitch and level Rough terrain May need to reduce ground speed, raise cutting height, and/or change direction of cut Ground speed too fast Slow speed to adjust for
Summary of the content on the page No. 17
TECHNICAL SPECIFICATIONS MODELS SWU36A-15KA, SWU48A-17KA, SWU52A-17KA ENGINE General Type: Heavy duty industrial/commercial Brand / Model: Kawasaki FH451V, Kawasaki FH500V Horsepower: Kawasaki FH451V = 15HP maximum @ 3600 RPM Kawasaki FH500V = 17HP maximum @ 3600RPM Type: Kawasaki = 15HP 4 cycle gas, air cooled, V twin cylinder, vertical shaft engine Kawasaki = 17HP 4 cycle gas, air cooled, V twin cylinder, vertical shaft engine Displacement: Kawasaki FH451V = 426 cc; Kawasaki FH500V = 494 cc Cy
Summary of the content on the page No. 18
TECHNICAL SPECIFICATIONS (CON'T) CUTTER DECK Type: Out-front floating design with anti-scalp rollers. Construction: 10-gauge steel reinforced with 7-gauge (3/16") Support plate. 7-gauge (3/16") deck skirt with easy clean-out design. True Cutting Width: 36.0 inches (90.2cm), 48.0 inches (122.0cm) Blade Engagement: Electric blade engagement clutch with control panel switch Cutting Height Adjustment: Manual adjustment 1" to 4-1/2" in 1/2" increments Cutter Blades: .197 Thick Marbane 36" = Two (2) 1
Summary of the content on the page No. 19
NOTES 15
Summary of the content on the page No. 20
36" CUTTER DECK 45 44 44 48 45 53 63 49 48 50 62 49 50 59 42 51 46 58 43 52 60 47 32 50 57 51 53 61 56 41 42 34 54 To"A" 41 55 50 47 40 "A" 36 13 39 13 34 37 39 64 38 1 33 2 20 3 4 21 35 22 23 5 24 7 13 32 31 8 12 6 5 14 11 25 26 9 16 10 15 9 27 19 19A 22 17 28 18 29 30 2001-SWU-CD36 16
Summary of the content on the page No. 1
OPERATOR’S MANUAL
MODEL SWU
PART NUMBER 03085
Summary of the content on the page No. 2
WARNING:
Summary of the content on the page No. 3
TABLE OF CONTENTS SUBJECT PAGE Introduction.................................................................................................. 1 General Safety Instructions ......................................................................... 1 Signal Words ............................................................................................... 1 Symbols....................................................................................................... 2-3 Before Operating .........
Summary of the content on the page No. 4
TABLE OF CONTENTS (CONTINUED) SUBJECT PAGE Illustrated Parts List Notes ................................................................................................ 15 SWMU - 36" Cutter Deck .................................................................. 16-17 SWMU - 48" & 52" Cutter Deck ........................................................ 18-19 Deck Frame - 36" .............................................................................. 20-21 Deck Frame - 48" & 52"................
Summary of the content on the page No. 5
INTRODUCTION SIGNAL WORDS .
/
*
# 0
Summary of the content on the page No. 6
48071S
WARNING FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS 481109 SEE OPERATOR'S MANUAL 2
Summary of the content on the page No. 7
! " # $
#& $!' "
! 481039S
!% *$# # (
) 3
Summary of the content on the page No. 8
BEFORE OPERATING WHILE OPERATING 5 =
1) 5 0
)
7 "
"
7 "
1
& 8 '
Summary of the content on the page No. 9
5> ,
0
H
) 1
0 # '
#
E
) '0 7
) '0 G I
,
C B
+ )
B
D '
Summary of the content on the page No. 10
H #
MOWER OPERATION
5 '
59
7
E
)
J + )
55
J ;
)
=
Summary of the content on the page No. 11
-NOTE- TRANSMISSION DRIVE BELT
!"
!
0*,
"
"#
"
0 " $ " 0
" !
Summary of the content on the page No. 12
X 6/ 8 " 0
"
" /+ " "
"
"
, "
/ 4/ ($
&
"
" "/ SWU99AG Figure 2. "Adjust-A-Grip" "
+, !+!- . #
" / & $
"
0
#
