Summary of the content on the page No. 1
OPERATOR’S MANUAL
MODEL GC-STT-CS
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMA-
TION FOR YOUR SCAG ACCESSORY. READ-
ING THIS MANUAL WILL PROVIDE YOU
WITH MAINTENANCE AND ADJUSTMENT
PROCEDURES TO KEEP YOUR ACCESSORY
PERFORMING TO MAXIMUM EFFICIENCY.
THE SPECIFIC MODELS THAT THIS BOOK
COVERS ARE CONTAINED ON THE INSIDE
COVER. BEFORE OPERATING YOUR MA-
CHINE, PLEASE READ ALL THE INFORMA-
TION ENCLOSED.
PART NUMBER 03140
Summary of the content on the page No. 2
WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning. * Keep hands, feet and clothing away from power-driven parts. * Read this manual completely as well as the Operator's Manual that came with your
Summary of the content on the page No. 3
2.1 SAFETY AND OPERATING 1.1 INTRODUCTION INSTRUCTIONS This manual has been prepared to provide the -NOTE- information you need to correctly assemble, operate, To avoid personal injury, it is imperative that all and maintain this grass catcher. Read it carefully and safety instructions be observed. keep it for future reference. 1. Read this operator's manual and the The replacement of any part on this product by other operator's manual that is supplied with the than the manufacturer's auth
Summary of the content on the page No. 4
5. To clean the hopper debris screen; 3. When dumping the hopper into a disposal area: A. Disengage the deck drive and allow all WARNING WARNING moving parts to come to a complete stop. DO NOT DUMP CLIPPINGS IN A DISPOSAL AREA THAT IS BURNING B. Apply parking brake and shut off the engine. A. Disengage the deck drive, apply the parking C. Stand on the left side of the hopper brake and allow all moving parts to come to assembly. a complete stop. D. Unhook the debris screen latches and B. Pul
Summary of the content on the page No. 5
3.1 ASSEMBLY INSTRUCTIONS FOR 52" 3. When installing this grass catcher on a machine CUTTER DECKS with a serial number below 8619999, you will need to remove the discharge baffle from the bottom of the cutter deck. See Figure 3-2. -NOTE- Replace the discharge baffle with the new baffle Use the illustrated parts list as a part provided with this grass catcher. Secure using number reference when following the the following hardware: assembly instructions. (1) 04001-12 Hex Head Bolt 5/16-18 x
Summary of the content on the page No. 6
LIFT LINK BELL CRANK SPACER NUT BOLT, 3/8-16 x 1-1/4" BOLT, 3/8-16 x 1-1/2" WASHER SPACER NUT CUTTER DECK REAR OF CUTTER DECK FRONT OF DISCHARGE CHUTE OPENING CUTTER DECK VIEW FROM RIGHT SIDE Figure 2-52"GC-STT install art OF CUTTER DECK FIGURE 3-3 BLOWER ELASTIC ASSEMBLY STOP NUTS HAIR PIN LOCK MOUNTING WASHERS POST PIN P R O P E R Y L CATCH S E C R E V I PLATE HEX HEAD E N N G E I BOLT W T H I O L I ELASTIC A N D STOP NUTS CARRIAGE F U E L . AND LOCK BOLTS WASHERS HEX HEAD
Summary of the content on the page No. 7
6. Install the blower mounting bracket to the deck 13. Install the plastic belt cover and secure with the using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- plastic wing nuts. See Page 20 of the Illustrated 71), 1/2" spring lockwashers (p/n 04030-06), and Parts List for proper installation. 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 3-3, Page 3. Do not fully tighten the 14. Install the hopper mounting brackets (p/n 451512 hardware at this time. & p/n 451595) to the outside of the frame o
Summary of the content on the page No. 8
18. Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine. Secure the weight bar to the machine using (2) bar clamps, (4) 3/8-16 x 1-1/2" bolts and (4) 3/8-16 elastic stop nuts. See Figure 3-6. 19. Install the weight assemblies to the weight support bar and secure them to the bar using the 1/2"x 6-1/4" pin and lanyard. See Figure 3-6 WEIGHT (5x) LANYARD ELASTIC STOP PIN NUT BAR
Summary of the content on the page No. 9
3. When installing this grass catcher on a machine 4.1 ASSEMBLY INSTRUCTIONS FOR 61" with a serial number below 8619999, you will CUTTER DECKS need to remove the discharge baffle from the bottom of the cutter deck. See Figure 3-2. -NOTE- Replace the discharge baffle with the new baffle Use the illustrated parts list as a part provided with this grass catcher. Secure using number reference when following the the following hardware: assembly instructions. (1) 04001-12 Hex Head Bolt 5/16-18
Summary of the content on the page No. 10
REAR OF CUTTER DECK FRONT OF DISCHARGE CHUTE OPENING CUTTER DECK VIEW FROM RIGHT SIDE OF CUTTER DECK Figure 2-61"GC-STT install art FIGURE 4-3 BLOWER ELASTIC ASSEMBLY STOP NUTS HAIR PIN MOUNTING LOCK POST WASHERS PIN ELASTIC STOP NUTS P R O P E R Y L AND LOCK CATCH WASHERS S E C R E V I PLATE E N N G E I W T H I O L I A N D CARRIAGE F U E L . BOLTS HEX HEAD BOLTS RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) GC-STT install art 3 FIGURE 4-4
Summary of the content on the page No. 11
6. Install the blower mounting bracket to the deck 12. Install the hopper mounting brackets (p/n 451512 using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- & p/n 451595) to the outside of the frame on the 71), 1/2" spring lockwashers (p/n 04030-06), and rear of the machine using 3/8-16 x 1" hex head 1/2-13 elastic stop nuts (p/n 04021-07). See bolts (p/n 04001-19) and 3/8-16 elastic stop nuts Figure 4-3, Page 8. Do not fully tighten the (p/n 04021-09). See Figure 5-6, Page 15. hardware at this tim
Summary of the content on the page No. 12
16. Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine. Secure the weight bar to the machine using (2) bar clamps, (4) 3/8-16 x 1-1/2" bolts and (4) 3/8-16 elastic stop nuts. See Figure 4-6. 17. Install the weight assemblies to the weight support bar and secure them to the bar using the 1/2"x 6-1/4" pin and lanyard. See Figure 4-6. WEIGHT (5x) LANYARD ELASTIC STOP PIN NUT BAR
Summary of the content on the page No. 13
3. When installing this grass catcher on a machine 5.1 ASSEMBLY INSTRUCTIONS FOR 72" with a serial number below 8619999, you will CUTTER DECKS need to remove the discharge baffle from the bottom of the cutter deck. See Figure 5-2. -NOTE- Replace the discharge baffle with the new baffle Use the illustrated parts list as a part provided with this grass catcher. Secure using number reference when following the the following hardware: assembly instructions. 1. Remove all packaging materials.
Summary of the content on the page No. 14
BLOWER ELASTIC ASSEMBLY STOP NUTS HAIR PIN MOUNTING LOCK POST WASHERS ELASTIC PIN STOP NUTS AND LOCK WASHERS CATCH PLATE CARRIAGE BOLTS HEX HEAD BOLTS RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) GC-STT install art 3 FIGURE 5-3 P R O P E R Y L S E C R E V I E N N G E I W T H I O L I A N D F U E L . 12
Summary of the content on the page No. 15
6. Install the blower mounting bracket to the deck 12. Install the plastic belt cover and secure with the using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- plastic wing nuts. See Page 20 of the Illustrated 71), 1/2" spring lockwashers (p/n 04030-06), and Parts List for proper installation. 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 5-3, Page 12. Do not fully tighten the 13. Install the hopper mounting brackets (p/n 451512 hardware at this time. & p/n 451595) to the outside of the frame
Summary of the content on the page No. 16
17. Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine. Secure the weight bar to the machine using (2) bar clamps, (4) 3/8-16 x 1-1/2" bolts and (4) 3/8-16 elastic stop nuts. See Figure 4-6. 18. Install the weight assemblies to the weight support bar and secure them to the bar using the 1/2"x 6-1/4" pin and lanyard. See Figure 5-5 WEIGHT (5x) LANYARD ELASTIC STOP PIN NUT BAR CL
Summary of the content on the page No. 17
Item # Part # Description 1 04001-19 Bolt, Hex Head 3/8-16 x 1" 2 04021-09 Nut, Elastic Stop 3/8-16 3 04066-03 Quick Pin 4 423670 Spacer, Hitch 5 451512 Hitch Bracket Weldment 451595 Hitch Bracket Weldment, Floating Hopper Assembly 5 1 2 3 Liquid Cooled 2 Only 1 4 1 Note: 2 Illustration is for reference only. Some parts have been Frame 3 removed for visual purposes and may vary depending 5 on model. FIGURE 5-6 15
Summary of the content on the page No. 18
6.1 GRASS CATCHER REMOVAL INSTRUCTIONS 1. Prepare the work area making sure that it is a REMOVE clean, safe environment. 2. Remove the rubber strap holding the adapter to the blower assembly. See Figure 5-1. 3. Remove the belt from the spindle pulley. 4. Remove the pin holding the blower assembly to the mounting bracket on the cutter deck and REMOVE remove the blower assembly. See Figure 5-1. ADAPTER FIGURE 5-2 6. With the help of an assistant, remove the hopper BLOWER MOUNTING ASSEMBL
Summary of the content on the page No. 19
Notes 17
Summary of the content on the page No. 20
WARNING INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL DANGER ROTATING BLADES AND BLOWER Stop engine before cleaning or removing DO NOT OPERATE MOWER UNLESS GRASS CATCHER OR DISCHARGE GUARD IS INSTALLED GC-STT BLOWER HOUSING ASSEMBLY 9 48 10 11 12 13 2 4 8 1 9 5 3 11 7 6 10 10 14 44 47 27 14 12 11 15 43 16 42 14 15 26 17 41 39 40 18 34 27 19 17 20 28 21 41 25 38 22 3 35 27 23 36 24 46 29 14 24 14 30 33 32 37 31 31 45 34 47 36 390STT0200A 45 35 49 18
