Summary of the content on the page No. 1
IMPORTANT MANUAL Do Not Throw Away
02478
OWNER'S MANUAL
WARNING:
Read this Owner's Manu al and follow all
MODEL:
Warnings and Safety Instructions. Fail ure
to do so can re sult in serious in ju ry.
PD22H42STC
LAWN TRACTOR
ALWAYS WEAR EYE PROTECTION DURING OPERATION
192727 4.28.04 MH
Printed in U.S.A.
Summary of the content on the page No. 2
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS . FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. DO NOT: I. GENERAL OPERATION Do not turn on slopes unless necessary, and then, Read, understand, and follow all instructions in the manual and on the machine before starting. turn slowly and gradually downhill, if possible. Only al
Summary of the content on the page No. 3
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS . FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. WARNING: In order to prevent ac- ci den tal starting when setting up, Never carry passengers or children even with the blades off. trans
Summary of the content on the page No. 4
CONGRATULATIONS on your purchase of a new tractor. PRODUCT SPECIFICATIONS It has been designed, engineered and manu fac tured to give GASOLINE CAPACITY 4.0 GALLONS you the best possible dependability and performance. AND TYPE: UNLEADED REGULAR Should you experience any problem you cannot easily rem- OIL TYPE (API-SG-SL): SAE 30 (above 32°F) edy, please contact your nearest authorized service center/ SAE 5W-30 (below 32°F) department. We have competent, w
Summary of the content on the page No. 5
UNASSEMBLED PARTS Seat Steering Wheel Steering Wheel Insert (1) Washer 17/32 x 1-3/16 x 12 Gauge (1) Knob Gauge Wheels Steering Extension Shaft Steering Sleeve (4) Clevis Pins (4) Wheels (4) Washers 3/8 x 3/4 x 14 Ga. Steering Adapter (4) Adjusting Bar (1) Large Flat Washer (4) Retainer Springs (4) Shoulder Bolt (double loop) (4) Locknut 3/8-16 (1) Oil Drain Tube (1) Locknut 1/2-20 Slope Sheet (1) Hex Bolt 1/4-28 x 1-1/4 (1) Locknut 1/4-28 (2) Keys 5
Summary of the content on the page No. 6
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY INSERT A socket wrench set will make assembly easier. Stan dard wrench sizes are listed. Utility knife Pliers 1/2 HEX NUT (1) 3/4" wrenches Tire pressure
Summary of the content on the page No. 7
ASSEMBLY TO DRIVE TRACT OR OFF SKID (See Op- INSTALL SEAT (See Fig. 3) er a tion section for location and function of Adjust seat before tightening adjustment knob. con trols) Remove adjustment knob and fl at washer securing W ARNING: Before start ing, read, un der stand and fol low seat to cardboard packing and set aside for assembly all in struc tions in the Op era tion section of this manu al. Be of seat to tractor. sure tractor is in a well-ventilated area. Be sure the area in
Summary of the content on the page No. 8
ASSEMBLY INSTALL MULCHER PLATE (See Figs. 4B) CHECK BRAKE SYSTEM Install two latch hooks to mulcher plate using screw, After you learn how to operate your tractor, check to see that washer, lock washer, and weld nut as shown. the brake is properly adjusted. See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual. NOTE: Pre-assemble weld nut to latch hook by in sert ing weld nut from the top with hook pointing down. ✓CHE CKLIST Tighten hardware securely. BEFOR
Summary of the content on the page No. 9
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. FAST IGNITION REVERSE NEUTRAL HIGH LOW SLOW CHOKE P LIGHTSON ENGINEON ENGINESTART PARKINGBRAKE ENGINEOFF PARKINGBRAKE PARKINGBRAKE LOCKED UNLOCKED FUEL OILPRESSURE BATTERY REVERSE FORWARD OVERTEMP MOWERHEIGHT MOWERLIFT LIGHT 15 15 ATTACHMENT ATTACHMENT SLOPEHAZARDS CLUTCHENGAGED CLUTCHDISENGAGED DANGER,KEEPHANDS KEEPAREACLEAR ANDFEETAWAY (SEESAFETYRULESSECTION) DA
Summary of the content on the page No. 10
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. IGNITION LIGHT AT TACHMENT SWITCH SWITCH CLUTCH LEVER AMMETER POSITION CHOKE CONTROL LIFT LEVER PLUNGER THROTTLE CONTROL ATTACHMENT LIFT LEVER CLUTCH/BRAKE PEDAL HEIGHT ADJUSTMENT KNOB PARKING BRAKE MOTION FREE WHEEL CONTRO
Summary of the content on the page No. 11
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per forming an y adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or stan dard safety glasses. IMPORTANT:LEAVING THE IGNITION SWITCH IN ANY HOW TO USE YOUR TRACTOR POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY TO BE DIS CHARGED, (DEAD). TO SET PARKING
Summary of the content on the page No. 12
OPERATION "ENGAGED" PO SI TION TO ADJUST GAUGE WHEELS (See Fig. 7) Gauge wheels are properly adjusted when they are slightly ATTACHMENT LIFT LEVER off the ground when mower is at the desired cutting height AT TACHMENT HIGH PO SI TION in operating position. Gauge wheels then keep the deck CLUTCH LEVER in proper position to help prevent scalping in most terrain "DIS EN GAGED" conditions. PO SI TION LOW NOTE:Adjust gauge wheels with tractor on a fl at level POSITION surface. Adjust mower
Summary of the content on the page No. 13
OPERATION Sit on seat in operating position, depress clutch/brake TOWING CARTS AND OTHER ATTA CH - pedal and set parking brake. MENTS Place motion control lever in neutral (N) position. Tow only the attachments that are recommended by and Move attachment clutch to “DISENGAGED” position. comply with specifi cations of the manufacturer of your trac- Move throttle control to fast position tor. Use common sense when towing. Too heavy of a load, Pull choke control out for a
Summary of the content on the page No. 14
OPERATION When mowing large areas, start by turning to the right so PURGE TRANSMISSION that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the CAUTION: Never engage or disengage opposite direction making left hand turns until fi nished freewheel lever while the engine is run- (See Fig. 10). ning. To ensure proper operation and performance, it is rec om - mend ed that the transmission be purged before operating tractor for the fi rst
Summary of the content on the page No. 15
OPERATION MULCHING MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN MAX 1/3 AFTER EACH USE. The spe cial mulch ing blade will recut the grass clip- pings man y times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biode- grade quick ly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will
Summary of the content on the page No. 16
MAINTENANCE MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE DATES Check Brake Operation Check Tire Pressure Check Operator Presence and Interlock Systems T R Check for Loose Fasteners 5 A Sharpen/Replace Mower Blades 3 C Lubrication Chart T Check Battery Level 4 0 Clean Battery and Terminals R Check Transaxle Cooling Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (without oil filter) 1,2 E Clean Air Filter N 2 G Clean Air
Summary of the content on the page No. 17
01202 MAINTENANCE TRACTOR MANDREL TRAILING ASSEMBLY EDGE UP Always observe safety rules when performing any main- BLADE te nance. CEN TER HOLE BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Ad just ments FLAT WASHER section of this manual). LOCK WASHER STAR TIRES Maintain proper air pressure in all tires (See “PROD UCT SPECIFICATIONS” section of this man
Summary of the content on the page No. 18
MAINTENANCE NOTE: The original equipment battery on your tractor is NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid necessary. possible engine damage from running low on oil. TO CLEAN BATTERY AND
Summary of the content on the page No. 19
MAINTENANCE CLEAN AIR SCREEN CLEANING Clean engine, battery, seat, fi nish, etc. of all foreign Air screen must be kept free of dirt and chaff to prevent matter. engine dam age from overheating. Clean with a wire brush or compressed air to re move dirt and stubborn dried gum Keep fi nished surfaces and wheels free of all gasoline, fi bers. oil, etc. Protect painted surfaces with automotive type wax. CLEAN AIR INTAKE/COOLING AREAS We do not recommend using a garden hose or pres
Summary of the content on the page No. 20
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS Depress clutch/brake pedal fully and set parking brake. Place motion control lever in neutral (N) position. Place attachment clutch in “DISENGAGED” position. Turn ignition key to “STOP” and remove key. Make sure the blades and all moving parts have completely stopped. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. IMPOR
