Summary of the content on the page No. 1
To The Owner • Carton Contents • Assembly • Parts Lists • Warranty
OPERATOR’S MANUAL
Twin Rear Bagger Kit
For Lawn Tractors
Model 190-180 & 190-182
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
FORM NO. 769-03178
PRINTED IN U.S.A. MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 4/3/2007
Summary of the content on the page No. 2
This Operator’s Manual is an important part of your new grass collector. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. TABLE OF CONTENTS 1. Rider Identification ........................................... Page 3 6. Attach Discharge Chute ..................................Page 10 2. Carton Contents .............................................. Page 4 7. Parts List .........................................................
Summary of the content on the page No. 3
™ FastAttach Twin Bag Model Plate Grass Collector The Model 190-180 and 190-182 Twin Bag Grass Collec- 1 tor is a grass collection system designed for use on all MTD 38”, 42” and 46” lawn tractors. Rider Model The instructions in this manual are divided into sections. Carefully read all sections pertaining to your model of Identification rider, and study the illustrations to ensure proper installa- tion and usage of this attachment. Read and observe all WARNING, NOTES and IMPORTANT statem
Summary of the content on the page No. 4
CONTENTS OF CARTON Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown in Fig. 2-1. 2 One Chute Tube One Support Tube One Discharge Chute Assembly One Grass Catcher Cover Assembly Carton Two Grass Bag Assemblies One Mounting Bracket Grass Catcher Support Brackets *Blades (Included in 46” Bagger Kits) Contents Discharge Chute If you are missing Assembly any parts, please Grass Catcher Cover Chute Tu
Summary of the content on the page No. 5
CONTENTS OF HARDWARE PACK This grass collector kit is shipped with a hardware pack enclosed. This hardware pack may contain extra parts for installation on a different rider from which you have. Please check your hardware pack against the 2 illustration below. Carton For decks with grass catcher pin not pre-installed (2) (1) Contents A1 B1* (1) (2) (1) E1 A2 B2* (1) (2) (8) E2 C1 D1 If you are missing any parts, please do not contact the retailer where you (2) (2) C2 purchased this uni
Summary of the content on the page No. 6
Attaching The Bracket Assembly Model Series 600 3 IMPORTANT: Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the Attaching tractor engine and set the parking brake. Bracket 1. For convenience, pivot the seat forward and leave it in that position until the grass collector is fully Assembly mounted and assembled. Model Series 600 2. Position the hooked ends of the bracket assembly over the shoulder bolts (1). Swing in the bottom of the bracket assem
Summary of the content on the page No. 7
Assembling Support Brackets Model Series 00 3 1. Locate the eight self-tapping screws supplied in your hardware pack (D1 from Fig. 2-2). Attach the right Attaching hand grass catcher support bracket using four of the supplied screws in position as shown in Fig. 3-3. Support Place the left hand grass catcher support bracket in position and secure with the other four screws. Bracket & NOTE: For easier installation, first align and start all four screws in each bracket before tighten
Summary of the content on the page No. 8
Attaching Grass Bags & Grass Bag Cover Inside Hole 1. Place the support tube in position on the rear of unit 4 by sliding the support tube down through the holes in the left side of the bracket assembly. Use the inside hole on the bracket assembly regardless of what size Attaching deck your tractor is equipped with. Refer to Fig. 4-1. Grass Bags 2. Attach the grass bags by hooking them onto the grass bag bracket using the slots in the grass bag and the & Grass Bag tabs on the grass bag
Summary of the content on the page No. 9
Attaching The Blades Smaller Blade Part No. 742-0645 NOTE: If your tractor is equipped with a 46” cutting deck, three 2-in-1 cutting blades are included with this kit. For improved bagging performance, install these blades on your tractor using the following instructions. Remove the blades from your tractor’s cutting deck as Attaching follows: 1. Remove the cutting deck from beneath the tractor, The Blades Larger Blades (refer to Deck Removal in the MAINTENANCE Part No. 742-0644 46-Inch
Summary of the content on the page No. 10
Attaching Discharge Chute 1. On some older models, a clip is already installed on 6 the cutting deck next to the discharge chute opening in position A, B, or C, as seen in Fig. 6-1. If this is Attaching the case, the clip must be removed and a grass catcher pin installed. Discharge 2. Pin Installation: A grass catcher pin (E1 in Fig. 2-2) and nut (E2 in Fig. 2-2) have been supplied in the Chute hardware pack. First remove the clip (if present), All Model Series as seen in Fig. 6-2A,
Summary of the content on the page No. 11
Attaching Discharge Chute All Model Series 6 1. Raise the deck to its highest position. Attaching 2. Raise the chute deflector on the deck and hold it while you position the discharge chute over the Discharge chute opening. 3. Place the top rear edge of the discharge chute over Chute the top rear edge of the chute opening. All Model Series 4. Push down on the discharge chute so that its front Retainer Strap bottom edge rolls around the bottom of the deck, then slide the chute forward t
Summary of the content on the page No. 12
3 45 47 41 44 39 46 42 12 40 21 37 13 17 28 48 16 43 9 38 1 15 5 27 For Deck 31 8 2 29 26 11 13 15 33 8 31 32 34 14 17 33 23 35 7 24 32 6 6 25 10 18 13 30 36 11 13 20 18 22 4 22 50 19 18 13 22 11 13 49 12
Summary of the content on the page No. 13
REF PART DESCRIPTION REF PART DESCRIPTION NO. NUMBER NO. NUMBER 1 16587D Support Bracket: Bagger 25 783-04968 Mounting Bracket, RH 2 16592 Support Tube Assembly 26 783-0601 Mounting Bracket Part List: 3 664-04017 Grass catcher Cover Assy. 27 783-0673B Mounting Bracket RH Rear Twin (includes Ref. 37 - 48) 28 783-0764B Mounting Bracket LH 4 710-0597 Screw 1/4-20 x 1” 29 783-0765 Bracket: Cross Support Bagger 5 710-0751 Hex Head Screw 1/4-20 x .62 30 764-0221 Catcher Bag Assembly 6 710-1260A
Summary of the content on the page No. 14
Al propietario • Contenido de la caja • Ensamblado • Listados de piezas • Garantía MANUAL DEL OPERADOR Kit de embolsado posterior doble Modelos 190-180 & 190-182 IMPORTANTE LEA CON ATENCIÓN LAS REGLAS DE SEGURIDAD E INSTRUCCIONES ANTES DE OPERAR LA UNIDAD IMPRESO EN ESTADOS MTD LLC. APARTADO POSTAL 361131 CLEVELAND, OHIO 44136-0019 UNIDOS DE AMÉRICA
Summary of the content on the page No. 15
Este Manual del Operador es una parte importante de su nuevo colector de césped. Le ayudará a montar, preparar y mantener la unidad para obtener los mejores resultados. Por favor, lea y com- prenda el contenido del manual. Búsqueda y registro del número de modelo ANTES DE COMENZAR A MONTAR SU NUEVO EQUIPO, por favor ubique la placa de modelo y copie la información de la misma en el Manual de Operador para referencia futura. La información contenida en la placa del modelo es muy importante en
Summary of the content on the page No. 16
Colector de césped Placa de modelo FastAttach™ con sistema de bolsa doble 1 Este Modelo 190-180 & 190-182 Coleccionista de Hierba de Bolso de Gemelo es un sistema de colección de Identificación hierba diseñado para el uso en todo MTD 38”, 42” & 46” tractores. del modelo Las instrucciones de este manual se dividen en sec- ciones. Lea con atención todas las secciones y estudie las ilustraciones para asegurar una adecuada instalación de podadora y uso de este aditamento. Lea y observe t
Summary of the content on the page No. 17
CONTENIDO DE CARTÓN Antes de la instalación que comienza, quite todas las partes del cartón para asegurarse que todo está presente. Los contenido de cartón son puestos en una lista abajo y mostrados en la Figura 2-1. Un Tubo de Tolva Un Tubo de Tolva 2 Una Asamblea de Tolva de Descarga Una Asamblea de Tolva de Descarga Dos Asambleas de Bolso de Hierba Dos Asambleas de Bolso de Hierba Contenido Escuadras de Soporte de Receptor de Hierba *Láminas (Incluido con equipos bagger para 46” Cubie
Summary of the content on the page No. 18
CONTENIDO DE PAQUETE DE HARDWARE Este equipo de coleccionista de hierba es transportado con un paquete de hardware encerrado. Este paquete de hardware puede contener extra partes para la instalación en un jinete diferente del cual usted 2 tiene. Por favor compruebe su paquete de hardware contra la ilustración abajo. Para cubiertas con alfiler de receptor Contenido de hierba no preinstalado (2) (1) A1 B1* de la caja (1) (2) (1) E1 A2 B2* (1) (2) (8) E2 C1 D1 Si le faltan piezas, por favor, n
Summary of the content on the page No. 19
Instalación Conjunto de soporte 3 Modelos series 600 IMPORTANTE: Antes del ensamblado, coloque el tractor sobre una superficie firme y nivelada, desen- Instalación ganche la toma de fuerza (PTO), detenga el motor del tractor y coloque el freno de estacionamiento. Conjunto de 1. Para mayor comodidad, gire el asiento hacia adelante soporte y déjelo en esa posición hasta que el colector de pasto esté totalmente colocado y ensamblado. Modelos Series 600 2. Coloque los extremos enganchados del
Summary of the content on the page No. 20
Ensamblado de los soportes 3 Modelo Serie 00 1. Localice los ocho tornillos de autogolpeado suminis- trados en su paquete de hardware (D1 del Higo 2-2). Instalación Ate la escuadra de soporte de receptor de hierba de mano derecha usando cuatro de los tornillos del soporte suministrados en la posición como mostrado en el Higo 3-3. Coloque la escuadra de soporte de receptor y del de hierba de mano izquierda en la posición y seguro con los otros cuatro tornillos. Figura 3-3 conjunto de
