Summary of the content on the page No. 1
Table of Contents
Powered Rakes
PR2572 & PR2596
10592
314-132M
Operator’s Manual
Read the Operator’s manual entirely. When
you see this symbol, the subsequent
!
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
© Copyright 2006 Printed 6/06/06
Cover photo may show optional equipment
not supplied with standard unit.
Summary of the content on the page No. 2
Land Pride Table of Contents Table of Contents Important Safety Information . . . . . . . . . . .1 Section 4: Optional Equipment . . . . . . . .16 Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1 Section 5: Maintenance & Lubrication . .17 Look For The Safety Alert Symbol . . . . . . . . . . . . . 1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Storage . . . . . . . . . . . . .
Summary of the content on the page No. 3
REMOVE Land Pride Table of Contents Important Safety Information Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Safety at All Times Look For The Safety Alert Symbol Thoroughly read and understand The SAFETY ALERT SYMBOL indicates there is a the instructions given in this potential hazard to personal safety involved and extra manual before operation. Refer to safety precaution must be taken. When you see this t
Summary of the content on the page No. 4
Land Pride Table of Contents Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Use the following maximum Use Safety Transport speed - tow load weight ratios as Lights and Devices Machinery Safely a guideline: 20 mph when weight is less Slow moving tractors, self- Comply with state and local laws. propelled equipment, and towed than or equal to the weight of Maximum transport speed for tractor. implements ca
Summary of the content on the page No. 5
Land Pride Table of Contents Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Wear Prepare for Emergencies Protective Equipment Be prepared if a fire starts. Protective clothing and equipment Keep a first aid kit and fire should be worn. extinguisher handy. Wear clothing and equipment Keep emergency numbers for appropriate for the job. Avoid doctor, ambulance, hospital and loose fitting clothing. fire departm
Summary of the content on the page No. 6
Land Pride Table of Contents Important Safety Information specified by Land Pride. When ordering new components Safety Labels make sure the correct safety labels are included in the Your Powered Rake comes equipped with all safety request. labels in place. They were designed to help you safely 4. Refer to this section for proper label placement. operate your implement. Read and follow their To install new labels: directions. a. Clean the area the label is to be placed. 1. Keep all safety labels
Summary of the content on the page No. 7
Land Pride Table of Contents Important Safety Information KEEP AWAY 818-254C Danger: Rotating Roller Hazard 15810 (Both Sides) 15813 818-255C Warning: General Safety 15810 818-540C Danger: Guard Missing 6/06/06 PR2572 & PR2596 Powered Rakes 314-132M 5
Summary of the content on the page No. 8
Land Pride Table of Contents Important Safety Information 818-540C 15811 Danger: Guard Missing ROTATING DRIVELINE 818-552C KEEP AWAY! 15811 Danger: Rotating Driveline 838-094C Warning: Hydraulic Pressure 10592 PR2572 & PR2596 Powered Rakes 314-132M 6/06/06 6
Summary of the content on the page No. 9
Land Pride Table of Contents Introduction Introduction Land Pride welcomes you to the growing family of new Serial Number Plate product owners. For prompt service always use the serial number and model number when ordering parts from your Land Pride This implement has been designed with care and built by dealer. Be sure to include your serial and model numbers skilled workers using quality materials. Proper assembly, in correspondence also. Refer to Figure 1 for the location maintenance, and saf
Summary of the content on the page No. 10
Land Pride Table of Contents Section 1: Assembly & Set-up Section 1: Assembly & Set-up 4. Remove the friction clutch (#7) that is assembled to Tractor Requirements the front of the front frame drive shaft (#8). (It is This powered rake is designed with a 3-Point category I assembled here for shipping only.) Assemble the hitch. Horse power rating of tractor should not exceed 50 friction clutch to the rear of the front frame drive shaft PTO horse power on all PR2572 & PR2596 Powered and gearbox as
Summary of the content on the page No. 11
Land Pride Table of Contents Section 1: Assembly & Set-up 4. Attach two of the rear tine mounts (#10) to the top Tines and Tine Frame Assembly tine lift arm (#4) and secure with 1” flatwashers (#5) and cotter pins (#6). NOTE: If your powered rake is not equipped with the optional tine package then skip this assembly 5. Attach the other two rear tine mounts (#10) to the tine procedure. frame (#2) with 1/2” lockwashers (#8) and 1/2” nuts (#9). Refer to Figure 1-3: 6. Install the tine frame assembl
Summary of the content on the page No. 12
Land Pride Table of Contents Section 1: Assembly & Set-up 10666 Lift Arm Location and Hose Routing Figure 1-4 10666 Tine Locations and Alignment Figure 1-5 PR2572 & PR2596 Powered Rakes 314-132M 6/06/06 10
Summary of the content on the page No. 13
Land Pride Table of Contents Section 1: Assembly & Set-up Shearing Hardware Assembly Angling Assembly Refer to Figure 1-6: Refer to Figure 1-8: Install shearing hardware bag (#1) as shown. Install the Install the manual angling turnbuckle (#1) or the optional three extra pins (#2) into the three pin storage holes on hydraulic cylinder (#2) as shown. the frame and secure with the cotter pins (#3). 15829 15827 Angling Assembly Figure 1-8 Shearing Hardware Assembly Figure 1-6 Tractor Hookup Tine Li
Summary of the content on the page No. 14
Land Pride Table of Contents Section 1: Assembly & Set-up Prior to initial operation and after long periods of Driveline Installation inactivity, the Friction Clutch should be “run-in”. Refer to 1. Slide the driveline over the splined shaft at the front of the powered rake and secure with the locking 1. Tighten all 4 nuts uniformly until the spring load is low device of driveline. enough that the clutch slips freely with the PTO engaged. IMPORTANT: The inner shield half hooks to the 2. Turn nuts
Summary of the content on the page No. 15
Land Pride Table of Contents Section 2: Operating Procedures Section 2: Operating Procedures Transporting Operating Instructions 1. Operate with 540 rpm PTO tractor. IMPORTANT: ALWAYS disengage PTO before 2. DO NOT engage PTO at full throttle. raising the powered rake to transport position. 3. Raking should not be done in wet conditions as soil 3. When raising the powered rake to the transport will stick between the bars on the roller and reduce position, be sure that powershaft does not contact
Summary of the content on the page No. 16
Land Pride Table of Contents Section 3: Adjustments Section 3: Adjustments powered rake is too high in the front then the rear portion Setting Depth and Leveling of the roller will cut deeper than the front portion of the roller when angled. IMPORTANT: It is very important that the powered rake be level front to rear and left to right for proper Setting The Depth performance. The powered rake must be level left to right before setting Leveling Left-To-Right the depth. The operating depth is cont
Summary of the content on the page No. 17
Land Pride Table of Contents Section 3: Adjustments Material Control Blade Adjustment IMPORTANT: Overtightening of chain may cause Refer to Figure 3-2: premature wear of sprockets and chain. The material control blade can be adjusted three ways: 4. Visually check the amount of adjustment left in the idler. If the adjustment is almost gone then it is time 1. The gap between the bottom of the material control to replace the drive chain and or the sprockets. See blade and the top of the roller can
Summary of the content on the page No. 18
Land Pride Table of Contents Section 4: Optional Equipment Section 4: Optional Equipment TINE FRAME ASSY PR2572 . . . . . . . . 314-044K TINE FRAME ASSY PR2596 . . . . . . . . 314-045K 15844 HYDRAULIC TINE LIFT BUNDLE . . . . .314-040L MANUAL TINE LIFT BUNDLE . . . . . . . .314-041L MANUAL ANGLING BUNDLE . . . . . . . 314-128A HYDRAULIC ANGLING BUNDLE . . . . 314-129A 15845 HYDRAULIC DIVERTER KIT . . . . . . . . 314-072A 15846 PR2572 & PR2596 Powered Rakes 314-132M 6/06/06 16
Summary of the content on the page No. 19
Land Pride Table of Contents Section 5: Maintenance & Lubrication Section 5: Maintenance & Lubrication Maintenance Drive Chain Maintenance Proper servicing and adjustment is the key to the long life The operator should check periodically to make sure that of any implement. With careful and systematic the drive chain is tight. If adjustment is needed refer to inspection, you can avoid costly maintenance, time and “Drive Chain Adjustment” on page 14. repair. Sprocket and Chain Replacement After us
Summary of the content on the page No. 20
Land Pride Table of Contents Section 5: Maintenance & Lubrication Bottom and Top Seal Installation Friction Clutch PTO If the bottom and top seals (#7) Figure 5-1 on page 17 Refer to Figure 5-4: need replacing refer to Figure 5-2 and Figure 5-3. Powered Rake drive components are protected from shock loads by a two plate friction clutch located between the gearbox and the drive shaft. The clutch should slip during operation to protect the powered rake from excessive loads. Prior to initial operat
