Summary of the content on the page No. 1
721
OWNERS MANUAL
for
POST-MIX
DISPENSERS
MODELS:
9454
9456
Includes:
Installation
Operation
Use & Care
Servicing Instructions
Model 9456
3-Flavor
Dispenser
p/n 83188 Rev. C ECN- 12738 M721 040811 cps
Summary of the content on the page No. 2
WARRANTY STATEMENT All electrical equipment manufactured by BLOOMFIELD It also does not apply if the serial nameplate has been INDUSTRIES is warranted against defects in materials and removed or unauthorized service personnel perform service. workmanship for a period of one year from the date of original The prices charged by Bloomfield Industries for its products installation or eighteen (18) months from the date of shipment are based upon the limitations in this warranty. Seller
Summary of the content on the page No. 3
TABLE OF CONTENTS WARRANTY STATEMENT xi Thank You for purchasing this Bloomfield Industries appliance. SPECIFICATIONS 1 FEATURES & OPERATING CONTROLS 2 Proper installation, professional PRECAUTIONS & GENERAL INFORMATION 5 operation and consistent AGENCY LISTING INFORMATION 5 maintenance of this appliance will ensure that it gives you the very INSTALLATION INSTRUCTIONS
Summary of the content on the page No. 4
FEATURES AND OPERATING CONTROLS 2
Summary of the content on the page No. 5
FEATURES AND OPERATING CONTROLS (continued) ITEM DESCRIPTION COMMENTS 1 WATER TANK 2 WATER LEVEL PROBES SENSE HIGH AND LOW WATER LEVELS DISPENSER WATER SUPPLY 9456 SHOWN. FOR 9454, CENTER TUBE IS BLANKED 3 TUBES 4 WATER TANK FILL TUBE 5 VENT / OVERFLOW 6 HEATING ELEMENT 1500 WATT ELEMENT TO HEAT WATER IN TANK 7 DRAIN FITTING DRAIN WATER TANK 8 WATER TANK COVER SHOWN OPEN DOOR / ILLUMINATED SHOWN OPEN - DOOR ASSY FOR 9454 & 9456 DIFFER 9 DISPLAY 10 PRODUCT HOPPER HOP
Summary of the content on the page No. 6
FEATURES AND OPERATING CONTROLS (continued) INTERNAL COMPONENTS ITEM DESCRIPTION COMMENTS 30 WHIPPER MOTORS 31 AUGER MOTOR 9454 QTY=2, 9456 QTY= 3 32 VENT "TEE" 33 DISPENSE SOLENOIDS TEMPERATURE CONTROL CONTROLS HEATING ELEMENT 34 THERMOSTAT 35 HI-LIMIT THERMOSTAT OVER-TEMP PROTECTION 36 WATER FILL SOLENOID SUPPLIES WATER TANK 37 COLD WATER "TEE" COLD BEVERAGE, LEFT DISPENSER ONLY 38 TRANSFORMER FOR FRONT DOOR LIGHTING 39 VACUUM BLOWER & MOTOR 9454 HAS TWO TUBES ONLY 40 DRAIN
Summary of the content on the page No. 7
PRECAUTIONS AND GENERAL INFORMATION WARNING: ELECTRIC SHOCK HAZARD All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock. WARNING: INJURY HAZARD All installation procedures must be performed by qualified personnel with full knowledge of all applicable electrical and plumbing codes. Failure could
Summary of the content on the page No. 8
INSTALLATION READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION IMPORTANT: Unpack the unit. Inspect all components for completeness and To enable the installer to make condition. Ensure that all packing materials have been removed a quality installation and to from the unit. minimize installation time, the Read all instructions in this manual carefully before starting following suggestions and tests installation of this fryer. READ AND UNDERSTAND ALL should be
Summary of the content on the page No. 9
INSTALLATION (continued) NSF requires that the brewer be able to be moved for cleaning WARNING: underneath. A flex line or loops of copper tubing will satisfy this SHOCK HAZARD requirement. See Figure 2 below. Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death or serious injury. IMPORTANT: Supply power must match nameplate for voltage a
Summary of the content on the page No. 10
OPERATION OPERATING MODES CAUTION: BURN HAZARD TO DISPENSE WATER SUPPLY SELECTOR SWITCH LEFT / CENTER / RIGHT SWITCH POSITION POSITIONS Exposed surfaces of dispenser and any container may be HOT WATERLINE OR HEATER ON HOT / HOT / HOT to the touch, and can cause PORTABLE HOT / HOT serious burns. HEATER ON COLD / HOT / HOT WATERLINE ONLY COLD / HOT Dispensed liquid may be hot to the touch and may cause burns WATERLINE OR HEATER OFF COLD / COLD / COLD PORTA
Summary of the content on the page No. 11
OPERATION (continued) INITIAL SET-UP: PORTABLE DISPENSERS CAUTION: BURN HAZARD 1. Turn POWER switch OFF. Exposed surfaces of dispenser Turn WATERLINE / PORTABLE switch to PORTABLE and any container may be HOT Turn HEATER switch OFF. to the touch, and can cause Turn COLD/HOT / HOT/HOT switch to HOT/HOT serious burns. Turn DISPENSE / FLUSH switch to flush 2. Add water to tank. CAUTION: NOTE: To avoid an overflow when the water
Summary of the content on the page No. 12
OPERATION (continued) NOTE: Hoppers and FILL PRODUCT HOPPERS motors for various products 1. Hoppers and covers should be thoroughly washed and dried. are essentially identical. Examine hoppers for completeness and proper assembly prior to In a cold / hot dispensing placing them into service. mode, the cold product must be placed in the left 2. Fill the hopper with the desired product powder and install the dispenser only. Otherwise, hopper cov
Summary of the content on the page No. 13
CLEANING INSTRUCTIONS PROCEDURE: Daily Cleaning - Dispenser CAUTION: BURN HAZARD PRECAUTIONS: Avoid splashing hot water from tank Hot water in the tank can cause FREQUENCY: Daily severe burns. Allow machine to TOOLS: Mild Detergent, Clean Soft Cloth or Sponge cool before moving or servicing. DO NOT tip or move machine when water in tank is hot. 1. Open front door. Turn the DISPENSE / FLUSH switch to the FLUSH
Summary of the content on the page No. 14
CLEANING INSTRUCTIONS (continued) CAUTION: PROCEDURE: Weekly Cleaning & Sanitizing BURN HAZARD PRECAUTIONS: Disconnect dispenser from electric power and Hot water in the tank can cause allow to cool. severe burns. Allow machine to Avoid splashing hot water from tank cool before moving or servicing. FREQUENCY: Weekly DO NOT tip or move machine when water in tank is hot. TOOLS: Small Flat
Summary of the content on the page No. 15
CLEANING INSTRUCTIONS (continued) PROCEDURE: Weekly Cleaning - Hoppers CAUTION: BURN HAZARD PRECAUTIONS: None Hot water in the tank can cause FREQUENCY: Weekly, or as necessary severe burns. Allow machine to TOOLS: Mild Detergent, Clean Soft Cloth or Sponge cool before moving or servicing. DO NOT tip or move machine when water in tank is hot. 1. When refilling hopper, inspect auger spring, star wheel and
Summary of the content on the page No. 16
TROUBLESHOOTING SUGGESTIONS CAUTION: SHOCK HAZARD Opening access panels may expose uninsulated electrical components. Disconnect dispenser from electrical power before removing any panel. Do not attempt to repair or replace components without first unplugging the power cord. Use caution when adjusting water flow rates or testing voltages with power applied to the unit. Electrical shock can cause injury or death. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION DISPENSER WILL NOT WORK Line
Summary of the content on the page No. 17
TROUBLESHOOTING SUGGESTIONS (continued) PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION WATER DRIPS OR FLOWS OUT Foreign particles inside dispense valve Remove valve coil, gently lift off valve SPOUT WITH POWER OFF dome and diaphragm, clean diaphragm Torn diaphragm in dispenser valve Replace diaphragm Defective dispense valve Replace dispense valve Inlet valve not completely closing Clean inlet valve/diaphragm DISPENSES WATER, BUT NOT Hopper empty Refill hopper with product PRODUCT Hopper
Summary of the content on the page No. 18
SERVICING INSTRUCTIONS HOT WATER ADJUSTMENT CAUTION: SHOCK HAZARD The desired taste of product being served is obtained by adjusting the water flow screw . Opening access panels may NOTE: When making the adjustment the selector switch must be expose uninsulated electrical in the HOT/HOT position. components. Disconnect dispenser from Each blender system has its own hot water dispense valve for electrical power before located behind the blender assembly
Summary of the content on the page No. 19
SERVICING INSTRUCTIONS COLD WATER ADJUSTMENT CAUTION: SHOCK HAZARD The dispenser can dispense both hot and cold beverage only when connected to a water line with the water supply valve Opening access panels may open. Cold product is available from the left dispenser only, and expose uninsulated electrical only when the COLD/HOT, HOT/ HOT selector switch is set in components. COLD/HOT position. Disconnect dispenser from 1. Unplug power cord. electrical power before
Summary of the content on the page No. 20
SERVICING INSTRUCTIONS (continued) REPLACE PRODUCT DELIVERY AUGER Before attempting major changes, such as installing a different rate product delivery auger, consult your product supplier for recommendations as to the required ratio product weight per volume of water. See the chart below for auger spring delivery rates. GRAMS p/n PRODUCT DELIVERY OUNCE OF WATER AUGER SPRING S6729 2.4 to 4.0 LESS PRODUCT AUGER SPRING S8501 4.1 to 4.6 STANDARD DELIVERY AUGER SPRING S3271
