Summary of the content on the page No. 1
Operators manual Models:
968999268 / LZ5225TKAA
968999269 / LZ6123LTKOA
968999270 / LZ6125TKAA
968999271 / LZ6127TKOA
968999272 / LZ7227TKOA
Please read these instructions carefully and make
sure you understand them before using the machine.
MANUAL NO. 539110972 REV. IR (09/08/04)
Summary of the content on the page No. 2
©2004 Husqvarna. All rights reserved. Beatrice, NE. Printed in U.S.A. 2
Summary of the content on the page No. 3
CONTENTS INTRODUCTION .................................. 4-5 OPERATING INSTRUCTIONS ............ 19 SYMBOLS & DECALS ......................... 6 Starting and operation ................. 19 SAFETY INSTRUCTIONS.................... 7 Controls ...................................... 19-20 General use and safety rules ...... 7-8 MAINTENANCE .................................... 21 Driving on slopes ........................ 9 Engine oil .................................... 21 Children safety............
Summary of the content on the page No. 4
INTRODUCTION Introduction Congratulations Thank you for purchasing a Husqvana ride-on mower. This machine is built for the greatest efficiency and rapid mowing of large areas. Convenient controls and a hydrostatic transmission regulated by steering levers also contribute to the machine’s performance. This manual is a valuable document. Following the instructions (use, service, maintenance, etc.) can considerably increase the life-span of your machine and even increase its resale value. If you se
Summary of the content on the page No. 5
INTRODUCTION Good Service Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer, see the certificate in the Service Journal in this operator’s manual. When you need spare parts or support in service questions, warranty issues, etc., please consult the follo
Summary of the content on the page No. 6
SYMBOLS AND DECALS Symbols and Decals These symbols are found on the machine and in the operator’s manual. Study them carefully so that you know what they mean. WARNING! Xxxxxxxxxx xxx xxxxx xxxxxxxx. Xxxxxx xxxxx xxxxxxxxx xxxxx xxxxx xxx x xxxxx. Used in this publication to notify the reader of a risk of personal injury, particularly if the reader should neglect to follow instructions given in the manual. IMPORTANT INFORMATION Xxxxxxx xxxx xxxxxxxx xxx xxx xxxx xxxxxx xx. Used in this pub
Summary of the content on the page No. 7
SAFETY INSTRUCTIONS Safety Instructions These instructions are for your safety. Read them carefully. WARNING! This symbol means that important safety instructions need to be emphasized. It concerns your safety. General Use • Read all instructions in this operator’s manual and on the machine before starting it. Ensure that you understand them and then abide by them. • Learn how to use the machine and its con- trols safely and learn how to stop quickly. Also learn to recognize the safety decals. •
Summary of the content on the page No. 8
SAFETY INSTRUCTIONS • Be careful when rounding fixed objects, so that the blades do not hit them. Never drive over WARNING! foreign objects. Engine exhaust and certain vehicle components contain or emit chemi- • Only use the machine in daylight or in other cals considered to cause cancer, well-lit conditions. Keep the machine a safe distance from holes or other irregularities in birth defects, or other reproductive the ground. Pay attention to other possible system damage. The engine ex- risks.
Summary of the content on the page No. 9
SAFETY INSTRUCTIONS Driving on Slopes Driving on slopes is one of the operations where the risk is greatest that the driver will lose control or the machine will tip over, which can result in serious injury or death. All slopes require extra caution. If you cannot reverse up a slope or if feel unsure, do not mow the slope. Do as follows: • Remove obstacles such as stones, tree branches, etc. • Mow up and down, not side-to-side. • Never drive the rider on terrain that slopes more than 10°. 6003-0
Summary of the content on the page No. 10
SAFETY INSTRUCTIONS Children: • Serious accidents may occur if you fail to be on guard for children in the vicinity of the ma- chine. Children are often attracted to the ma- chine and mowing work. Never assume that children will stay put where you last saw them. • Keep children away from the mowing area and under close supervision by another adult. • Keep an eye out and shut off the machine if children enter the work area. • Before and during a reversing maneuver, look backward and downward for
Summary of the content on the page No. 11
SAFETY INSTRUCTIONS • Allow the engine to cool before refueling. Do not smoke. Do not fill fuel in the vicinity of sparks or open flames. WARNING! The engine, the exhaust system, • If leaks arise in the fuel system, the engine must not be started until the problem has been and the hydraulic system’s compo- resolved. nents become very warm during operation. • Store the machine and fuel in such a way that Risk for burns if touched. there is no risk of leaking fuel or fuel vapor leading to damages.
Summary of the content on the page No. 12
SAFETY INSTRUCTIONS • Never use the machine indoors or in spaces lacking proper ventilation. The exhaust fumes contain carbon monoxide, and odorless, poi- sonous, and lethal gas. • Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting. • Never make adjustments with the engine run- ning. • The machine is tested and approved only with the equipment originally provided or recom- mended by the manufacturer. • The blades are sharp and can cause cu
Summary of the content on the page No. 13
SAFETY INSTRUCTIONS Roll Over Protection System WARNING! This structure’s capability may be imparired by structural damage if overturned, or al- teration occurs. If any of these conditions take place, the total structure MUST be re- placed. DO NOT use ROPS as a lifting, attaching or anchoring point. DO NOT exceed Max GVW: 2822; ROPS mass 42 lbs./19 kg. Read machine operator’s manual before each use. Securely fasten your seat belt if the unit has a ROPS. Where possible, avoid operating the unit n
Summary of the content on the page No. 14
PRESENTATION Presentation Thank you for buying a HUSQVARNA! Before Lawnmowers and all power equipment, can be operating your new mower, read, understand and potentially dangerous if used improperly. Safety follow the safety instructions and other directions requires good judgement, careful use in accor- in this manual. dance with these instructions and common sense. ROPS MOTION CONTROL LEVERS DECK LIFT LEVER KEY SWITCH FUEL CAP THROTTLE PARKING FOOT BRAKE PLATE BLADE ENGAGEMENT HOUR SWITCH METER
Summary of the content on the page No. 15
SETUP AND ADJUSTMENTS WARNING! No settings or adjustments are to be made unless: Engine is stopped, key has been removed, park brake is on and bat- 4. Torque all 1/2” hardware to 80 ft./lbs. (110 N•m). tery cable removed from battery. 5. Install and tighten knobs against the side post. Setup Uncrate machine. LATCH PIN TOP LOOP ROPS Assembly (Roll Over Protection System) KNOB ROPS Assembly Components 1 - Top Loop 1/2C X 3 1/4 CAPSCREW 1 - Left Side Post 1/2C CENTERLOCK 1 - Right Side Post NUT 1 -
Summary of the content on the page No. 16
SETUP AND ADJUSTMENTS Control Arms Remove top bolt in control arm and loosen bot- tom bolt, rotate the control levers to the upright position. Align the levers so they are even in the neutral position. Reinstall hardware and tighten. Control Motion FIG - 1 Arm Control Lever Seat Install 1. Remove seat assembly from the crate. 2. Remove the four 5/16C nyloc nuts or 5/16C studed knobs from the bottom of the seat. Retain for use later. 3. Align the seat bottom with the holes in the seat frame. Plac
Summary of the content on the page No. 17
SETUP AND ADJUSTMENTS Loosen the nuts directly behind each ball joint on Mower Deck Leveling both rods that connect the pump arm to the mo- Position machine on a flat surface. Preferably level concrete. tion control assemblies. FIG - 5 Check the tire pressure in all four tires. Inflation Start the engine. The park brake must be engaged should be 15 psi. and the motion control levers in the neutral slots to start the engine. Run the engine approximately Place 2x4’s on edge under the cutting deck
Summary of the content on the page No. 18
SETUP AND ADJUSTMENTS Park Brake Adjustment When the park brake is on, the spring should If the 1/4” gap is not adjusted follow these step: measure 2 3/4” to2 7/8” and have a 1/4”-3/8” gap 1. Place the park brake in the off position. between the brake yoke and the washer on the 2. Loosen the 3/8F nut holding the yoke and re- lower brake rod. move the clevis pin. 3. Turn the yoke clockwise to increase the gap. If the spring needs adjusting follow these steps: 4. Reinstall the yoke to the brake le
Summary of the content on the page No. 19
OPERATING INSTRUCTIONS Operating instructions Roll Bar and Seat Belt By moving the levers an equal amount forward or Operate the unit with the roll bar in the raised and back the machine will move in a straight line in locked position and use seat belt. There is no rollover protection when the roll bar is down. If it is that direction. FIG - 7 necessary to lower roll bar do not wear the seat belt. Raise the roll bar as soon as clearance per- Movement of either lever forward will cause the mits.
Summary of the content on the page No. 20
OPERATING INSTRUCTIONS Key Switch Key switch is located on the console. Used to start the machine. NOTE: Do not run the starter for more than 5 seconds at a time. If the engine will Choke Throttle not start, wait about 10 seconds before trying again. FIG - 8 Key Switch Hour Meter Blade The hour meter displays the total operating time Engagement and reminds of service intervals. The meter will indicate “CHG OIL” for engine oil and “SVC” for general service at preset intervals. The hour meter will
